2014 NISSAN TEANA ignition

TCM
TM-49
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000009464001
CONSULT DATA MONITOR STANDARD VALUE
• In CONSULT, electric shift timing or lock-up timing, i. e. operation timing of each solenoid valve, is displayed.
Therefore, if there is an obvious difference between t he shift timing estimated from a shift shock (or engine
speed variations) and that shown on the CONSULT, the mechanism parts (including the hydraulic circuit)
excluding the solenoids and sensors may be malfunctioning. In this case, check the mechanical parts follow-
ing the appropriate diagnosis procedure.
• Shift point (gear position) displayed on CONSULT slight ly differs from shift pattern described in Service Man-
ual. This is due to the following reasons.
- Actual shift pattern may vary slightly within specified tolerances.
- While shift pattern described in Service Manual indica tes start of each shift, CONSULT shows gear position
at end of shift.
- The solenoid display (ON/OFF) on CONSULT is changed at the start of gear shifting. In contrast, the gear
position display is changed at the time when gear shif ting calculated in the control unit is completed.
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item Condition Value/Status (Approx.)
VSP SENSOR While driving Almost same as the speedometer display.
ESTM VSP SIG While driving Almost same as the speedometer display.
INPUT SPEED SENSOR In driving (lock-up ON) Ap proximately matches the engine speed.
PRI SPEED SEN In driving (lock-up ON) Approximately matches the engine speed.
SEC REV SENSOR While driving VSP SENSOR × 40
ENG SPEED SIG Engine ru nning Almost same reading as tachometer
SEC PRESSURE SEN • After engine warm up
• Selector lever: “N” position
• At idle 1.2 – 1.3 V
PRI PRESSURE SEN • After engine warm up
• Selector lever: “N” position
• At idle 0.70 – 0.85 V
ATF TEMP SEN CVT fluid: Approx. 20
°C (68 °F) 2.01 – 2.05 V
CVT fluid: Approx. 50 °C (122 °F) 1.45 – 1.50 V
CVT fluid: Approx. 80 °C (176 °F) 0.90 – 0.94 V
G SENSOR Vehicle is level 0 V
VIGN SEN Ignition switch: ON 10 – 16 V
PVING VOLT Ignition switch: ON 10 – 16 V
VEHICLE SPEED While driving Almost sa me as the speedometer display.
INPUT REV In driving (lock-up ON) Almost same as the engine speed.
PRI SPEED In driving (lock-up ON) Approximately matches the engine speed.
SEC SPEED While driving VSP SENSOR × 40
ENG SPEED Engine running Almost same reading as tachometer
SLIP REV While driving Engine speed − Input speed
PULLEY GEAR RATIO In driving (forward) 2.70
− 0.38
In driving (reverse) 2.70
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-50
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F10D]
TCM
G SPEEDVehicle stopped 0.00 G
During acceleration The value changes to the positive side
along with acceleration.
During deceleration The value changes to the positive side
along with deceleration.
ACCEL POSI SEN 1 Accelerator pedal released 0.00 deg
Accelerator pedal fully depressed 80.00 deg
VENG TRQ While driving The value changes along with acceleration/
deceleration.
PRI TRQ While driving The value changes along with acceleration/
deceleration.
TRQ RTO While driving The value changes along with acceleration/
deceleration.
SEC PRESSURE • After engine warm up
• Selector lever: “N” position
•At idle 1.1 MPa
PRI PRESSURE • After engine warm up
• Selector lever: “N” position
•At idle 0.40 – 0.45 MPa
FLUID TEMP Ignition switch ON. Displays the CVT fluid temperature.
DSR REV While driving It varies along with the driving condition.
TGT PLLY GR RATIO In driving (forward) 2.70
− 0.38
In driving (reverse) 2.70
LU PRS • Engine started
• Vehicle is stopped. −
0.500 MPa
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 20 km/h (12 MPH) or more 0.450 MPa
LINE PRS • After engine warm up
• Selector lever: “N” position
•At idle 1.1 MPa
TRGT PRI PRESSURE • After engine warm up
• Selector lever: “N” position
•At idle 0.40 – 0.45 MPa
TRGT SELECT PRESSURE • After engine warm up
• Selector lever: “N” position
•At idle 0 MPa
• Selector lever: “D” position
•At idle 0.3 – 0.5 MPa
TRGT SEC PRESSURE • After engine warm up
• Selector lever: “N” position
•At idle 1.1 MPa
ISOLT1 • Engine started
• Vehicle is stopped. 0.000 A
• Selector lever: “D” position
• Accelerator pedal position: 1/8 or less
• Vehicle speed: 20 km/h (12 MPH) or more 0.500 A
ISOLT2 • After engine warm up
• Selector lever: “N” position
•At idle 0.800 – 0.850 A
Monitor item Condition Value/Status (Approx.)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-52
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F10D]
TCM
MMODE Always Off
TOW MODE SW Always Off
SHIFT IND SIGNAL When the selector lever is positioned in be-
tween each position. OFF
Selector lever: P position P
Selector lever: R position R
Selector lever: N position N
Selector lever: D position D
CVT LAMP Approx. 2 seconds after ignition switch ON On
Other than the above Off
SPORT MODE IND In overdrive off On
Other than the above Off
MANU MODE SIGNAL Always Off
DS RANGE SIGNAL Selector lever in DS position On
Other than the above Off
ECO MODE SIGNAL Always Off
VDC ON Always Off
TCS ON Always Off
ABS FAIL SIGNAL When ABS malfunction signal is received On
Other than the above Off
ABS ON ABS is activated On
Other than the above Off
RANGE Selector lever: P and N positions N/P
Selector lever: R position R
Selector lever: D position D
Selector lever: DS position S
Selector lever: D position (in O/D OFF) S
M GEAR POS Always 1
G SEN SLOPE Flat road 0%
Uphill gradient The value changes to the positive side
along with uphill gradient. (Maximum
40.45%)
Downhill gradient The value changes to the negative side
along with downhill gradient. (Minimum
40.45%)
G SEN CALIBRATION When G sensor calibration is completed DONE
When G sensor calibration is not completed YET
N IDLE STATUS Always Off
ENGBRKLVL When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is ON On
When the engine brake level of “ENGINE
BRAKE ADJ”. in “Work Support” is OFF Off
DRIVE MODE STATS While driving in D position AUTO
SNOW MODE Always Off
ECO MODE Always Off
NOTMAL MODE Always Off
SPORT MODE Always Off Monitor item Condition Value/Status (Approx.)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TCM
TM-53
< ECU DIAGNOSIS INFORMATION > [CVT: RE0F10D]
C
EF
G H
I
J
K L
M A
B
TM
N
O P*: These monitor items do not use.
TERMINAL LAYOUT
INPUT/OUTPUT SIGNAL STANDARD
AIR BLDING STATE Always COMP
ELECTRIC OP DUTY Always 0%
E-OP DUTY MON Always 0%
ELECTRIC OP RELAY Always Off
E-OP RELAY MON Always Off
CVT-B* — —
CVT-A* — — Monitor item Condition Value/Status (Approx.)
JSDIA2713ZZ
Te r m i n a l N o .
(Wire color) Description
Condition Value (Approx.)
+ − Signal Input/
Output
2
(SB) Ground DS position switch Input
Ignition
switch
ON Selector lever: “DS” posi-
tion 10
− 16 V
Other than the above 0 V
4
(LG) Ground D position switch Input Selector lever:
“D” position 10 − 16 V
Other than the above 0 V
5
(BR) Ground N position switch Input Selector lever:
“N” position 10 − 16 V
Other than the above 0 V
6
(L) Ground R position switch Input Selector lever:
“R” position 10 − 16 V
Other than the above 0 V
7
(V) Ground P position switch Input Selector lever:
“P” position 10 − 16 V
Other than the above 0 V
11
(Y) Ground Sensor ground Input Always 0 V
12
(V) Ground CVT fluid tempera-
ture sensor OutputIgnition
switch
ON CVT fluid: Approx. 20
°C
(68 °F) 2.01 – 2.05 V
CVT fluid: Approx. 50 °C
(122 °F) 1.45 – 1.50 V
CVT fluid: Approx. 80 °C
176 °F) 0.90 – 0.94 V
16
(Y) Ground
Secondary pres-
sure sensor Input
• Selector lever: “N” position
• At idle 1.67 – 1.69 V
17
(LG) Ground Primary pressure
sensor Input• Selector lever: “N” position
• At idle 0.90 – 0.92 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-54
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F10D]
TCM
23
(P) —CAN-L
Input/
Output ——
24
(BR) Ground Input speed sensor Input • Selector lever:
“DS” position
• Vehicle speed: 20 km/h (12 MPH) 880 Hz
26
(LG) Ground Sensor power sup-
ply OutputIgnition switch: ON 5.0 V
Ignition switch: OFF 0 V
30
(BR) Ground Line pressure sole-
noid valve Output• After engine warming up
• Selector lever: “N” position
• At idle
• After engine warming up
• Selector lever: “N” position
• Depress the acce lerator pedal fully
33
(L) —CAN-H
Input/
Output ——
34
(V) Ground Output speed sen-
sor Input• Selector lever:
“DS” position
• Vehicle speed: 20 km/h (12 MPH) 200 Hz
35
(BR) Ground
Primary speed sen-
sor Input
• Selector lever:
“DS” position
• Vehicle speed: 20 km/h (12 MPH) 700 Hz
Te r m i n a l N o .
(Wire color) Description
Condition Value (Approx.)
+ − Signal Input/
Output
JSDIA3769GB
JSDIA1897GB
JSDIA1898GB
JSDIA1904GB
JSDIA1905GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-56
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F10D]
TCM
Fail-safe
INFOID:0000000009464002
TCM has a fail-safe mode. The mode functions so that operation can be continued even if the signal circuit of
the main electronically contro lled input/output parts is damaged.
If the vehicle shows following behaviors including “poor acceleration”, a malfunction of the applicable system
is detected by TCM and the vehicle may be in a fail-sa fe mode. At this time, check the DTC code and perform
inspection and repair according to the malfunction diagnosis procedures.
Fail-safe function
46
(P) Ground
Battery power sup-
ply (backup) Input Always 10
− 16 V
47
(Y) Ground Ignition power sup-
ply InputIgnition switch: ON 10
− 16 V
Ignition switch: OFF 0 V
48
(Y) Ground Ignition power sup-
ply InputIgnition switch: ON 10
− 16 V
Ignition switch: OFF 0 V
Te r m i n a l N o .
(Wire color) Description
Condition Value (Approx.)
+ − Signal Input/
Output
DTC Vehicle behavior Conditions of vehicle
P062F • Not changed from normal driving —
P0705 • Shift position indicator on combination meter is not dis-
played
• Selector shock is large
•Start is slow
• Acceleration is slow
• Lock-up is not performed —
P0706 • Shift position indicator on combination meter is not dis-
played
• Selector shock is large
•Start is slow
• Acceleration is slow
• Lock-up is not performed —
P0711 •Start is slow
• Acceleration is slow Engine coolant temperature when engine start:
Te m p . ≥ 10 °C (50 °F)
• Selector shock is large
•Start is slow
• Acceleration is slow Engine coolant temperature when engine start:
− 35 °C ( −31 °F) ≤ Temp. < 10 °C (50 °F)
• Selector shock is large
•Start is slow
• Acceleration is slow Engine coolant temperature when engine star:
Te m p . < −35 °C ( −31 °F)
P0712 •Start is slow
• Acceleration is slow Engine coolant temperature when engine start:
Te m p . ≥ 10 °C (50 °F)
• Selector shock is large
•Start is slow
• Acceleration is slow Engine coolant temperature when engine start:
− 35 °C ( −31 °F) ≤ Temp. < 10 °C (50 °F)
• Selector shock is large
•Start is slow
• Acceleration is slow Engine coolant temperature when engine star:
Te m p . < −35 °C ( −31 °F)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-60
< ECU DIAGNOSIS INFORMATION >[CVT: RE0F10D]
TCM
DTC Index
INFOID:0000000009464005
NOTE:
• If multiple malfunction codes are detected at the same time, check each code according to the “DTC check
priority list”. Refer to TM-59, "DTC Inspection Priority Chart"
.
• The ignition counter is displayed in “FFD”. Refer to TM-43, "CONSULT Function"
.
2P0740 TORQUE CONVERTER
TM-120, "DTC Logic"
P0743 TORQUE CONVERTERTM-122, "DTC Logic"
P0778 PC SOLENOID BTM-130, "DTC Logic"
P0779 PC SOLENOID BTM-132, "DTC Logic"
P0962 PC SOLENOID ATM-145, "DTC Logic"
P0963 PC SOLENOID ATM-147, "DTC Logic"
P0966 PC SOLENOID BTM-151, "DTC Logic"
P0967 PC SOLENOID BTM-153, "DTC Logic"
P2814 SELECT SOLENOIDTM-160, "DTC Logic"
P2815 SELECT SOLENOIDTM-162, "DTC Logic"
3P062F EEPROM
TM-96, "DTC Logic"
P0705 T/M RANGE SENSOR ATM-97, "DTC Logic"
P0706 T/M RANGE SENSOR ATM-103, "DTC Logic"
P0711 FLUID TEMP SENSOR ATM-106, "DTC Logic"
P0712 FLUID TEMP SENSOR A TM-110, "DTC Logic"
P0713 FLUID TEMP SENSOR ATM-112, "DTC Logic"
P0715 INPUT SPEED SENSOR ATM-114, "DTC Logic"
P0717 INPUT SPEED SENSOR ATM-117, "DTC Logic"
P0841 FLUID PRESS SEN/SW ATM-134, "DTC Logic"
P0847 FLUID PRESS SEN/SW BTM-135, "DTC Logic"
P0848 FLUID PRESS SEN/SW BTM-137, "DTC Logic"
P084C FLUID PRESS SEN/SW HTM-139, "DTC Logic"
P084D FLUID PRESS SEN/SW HTM-141, "DTC Logic"
P0890 TCMTM-144, "DTC Logic"
P2765 INPUT SPEED SENSOR BTM-155, "DTC Logic"
4P0744 TORQUE CONVERTER
TM-124, "DTC Logic"
P0746 PC SOLENOID ATM-126, "DTC Logic"
P0776 PC SOLENOID BTM-128, "DTC Logic"
P0965 PC SOLENOID BTM-149, "DTC Logic"
P2813 SELECT SOLENOIDTM-158, "DTC Logic"
Priority DTC (Diagnostic Trouble Code) Reference
DTC*1, *2
Items
(CONSULT screen terms) Trip
MIL*3Reference
GST CONSULT
(TRANSMISSION)
P062F P062F EEPROM 1 ON TM-96
P0705 P0705 T/M RANGE SENSOR A 2 ONTM-97
P0706 P0706 T/M RANGE SENSOR A 2 ONTM-103
P0711 P0711 FLUID TEMP SENSOR A 2 ONTM-106
P0712 P0712 FLUID TEMP SENSOR A 2 ON TM-110
P0713 P0713 FLUID TEMP SENSOR A 2 ONTM-112
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-80
< BASIC INSPECTION >[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TCM
ADDITIONAL SERVICE WHEN REPLACING TCM
DescriptionINFOID:0000000009464010
Always perform the following items when the TCM is replaced.
SAVING AND WRITING OF TCM DATA• TCM performs accurate control by retrieving data (inher
ent characteristic value) of each solenoid. For this
reason, it is necessary to save data of current TCM in CONSULT before replacing the TCM. After this, the
saved data must be written in new TCM.
Work ProcedureINFOID:0000000009464011
CAUTION:
When replacing TCM together with transaxle assembly, perform “ADDITIONAL SERVICE WHEN
REPLACING TRANSAXLE ASSEMBLY”. Refer to TM-81, "Work Procedure"
.
1.SAVE THE TCM DATA
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions:
1. Turn ignition switch OFF and wait for 10 seconds.
2. Turn ignition switch ON.
3. Select “Work Support” in “TRANSMISSION”.
4. Select “READ IP CHARA - REPLACEMENT TCM”.
5. Import data according to the in structions on the CONSULT screen.
>> GO TO 2.
2.REPLACE THE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace the TCM. Refer to TM-183, "Removal and Installation"
.
>> GO TO 3.
3.WRITE THE TCM DATA
NOTE:
Write data saved in CONSULT into a new TCM according to the following instructions:
1. Turn ignition switch OFF and wait for 10 seconds.
2. Turn ignition switch ON.
3. Select “Work Support” in “TRANSMISSION”.
4. Select “WRITE IP CHARA - REPLACEMENT TCM”.
5. Write data saved in CONSULT in TCM according to the instructions on the CONSULT screen.
>> WORK END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM