2014 NISSAN TEANA warning

DAS
NORMAL OPERATING CONDITIONDAS-141
< SYMPTOM DIAGNOSIS > [LDW]
C
D E
F
G H
I
J
K L
M B
N P
A
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000009464793
PRECAUTIONS FOR LANE DEPARTURE WARNING (LDW)
• LDW system is only a warning devic e to inform the driver of a potential unintended lane departure. It will not
steer the vehicle or prevent loss of c ontrol. It is the driver’s responsibility to stay alert, drive safely, keep the
vehicle in the traveling lane, and be in control of the vehicle at all times.
• LDW system will not operate at s peeds below approximately 70 km/h (45 MPH) or if it cannot detect lane
markers.
• Excessive noise will interfere with the warning chime sound, and the chime may not be heard.
• LDW system may not function proper ly under the following conditions:
- On roads where there are multiple parallel lane marker s; lane markers that are faded or not painted clearly;
yellow painted lane markers; non-standard lane markers; or lane markers covered with water, dirt or snow,
etc.
- On roads where the discontinued lane markers are still detectable.
- On roads where there are sharp curves.
- On roads where there are sharply contrasting objects, such as shadows, snow, water, wheel ruts, seams or
lines remaining after road repairs. (The LDW syst em could detect these items as lane markers.)
- On roads where the traveling lane merges or separates.
- When the vehicle's traveling direction does not align with the lane marker.
- When traveling close to other vehicle in front of the vehicle, which obstructs the lane camera unit detection
range.
- When rain, snow or dirt adheres to the windshield in front of the lane camera unit.
- When a sudden change in brightness occurs. (For exampl e, when the vehicle enters or exits a tunnel or
under a bridge.)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-142
< REMOVAL AND INSTALLATION >[LDW]
WARNING SYSTEMS SWITCH
REMOVAL AND INSTALLATION
WARNING SYSTEMS SWITCH
Removal and InstallationINFOID:0000000009464796
REMOVAL
1. Remove the instrument lower panel LH. Refer to
IP-21, "Removal and Installation".
2. Remove screws ( ) that retain the upper switch carrier (1) to the instrument lower panel LH (2).
3. Release upper tab (B) and lower tab (C) using a suitable tool (A), then remove the warning system switch (4) from the upper
switch carrier.
(1) Trunk opener switch
(2) VDC switch
(3) Heated steering wheel switch
INSTALLATION
Installation is in the reverse order of removal.
ALOIA0143ZZ
ALOIA0144ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-146
< PRECAUTION >[BSW]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951647
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009464801
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Precautions For Harness RepairINFOID:0000000009464802
ITS communication uses a twisted pair line. Be careful when repairing it.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
PRECAUTIONSDAS-147
< PRECAUTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
• Solder the repaired area and wrap tape around the soldered area. NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
• Bypass connection is never allowed at the repaired area. NOTE:
Bypass connection may cause ITS communication error. The
spliced wire becomes separated and t he characteristics of twisted
line are lost.
Precaution for BSW System ServiceINFOID:0000000009464803
WARNING:
Be cautious of traffic conditions and ot her vehicles when performing a road test.
CAUTION:
• Do not use the BSW system when driving with free rollers or on a chassis dynamometer.
• Do not perform BSW ACTIVE TESTS while driving.
• Do not disassemble or alter the rear view camera.
• Do not use the rear view camera when removed from the vehicle.
• Do not disable the BSW system without the consent of the customer.
OBSERVE THE FOLLOWING ITEMS IN ORDER TO KEEP THE BSW SYSTEM OPERATING
PROPERLY:
Rear view Camera Maintenance
The rear view camera for the BSW system is located in the truck lid. To keep the BSW system operating prop-
erly and prevent a malfunction, be sure to observe the following:
• Always keep the camera lens area clean.
• Do not attach bumper stickers (including transparent ma terials) or install an accessory near the rear view-
camera.
• Do not strike or damage the areas around the rear view camera.
• Do not touch the camera lens (except for cleaning) or remove the rear view camera.
SKIB8766E
SKIB8767E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-150
< SYSTEM DESCRIPTION >[BSW]
COMPONENT PARTS
Component Description
INFOID:0000000009464806
1. Combination meter 2. Vehicle information display 3. BCM (view with combination meter re- moved)
4. Blind spot warning indicator RH 5. Blind spot warning indicator LH 6. TCM
7. ECM 8. Warning systems switch 9. Warning systems ON indicator
10. Rear view camera washer control unit 11. Rear view camera air pump motor 12. Rear view camera
13. AV control unit (center display) (with navi- gation system and bose audio system)
Audio unit (center display) (with display
audio system and bose audio system) 14. ITS control unit
(view with center console removed) 15. Steering angle sensor
(view with steeri ng wheel removed)
16. Washer fluid level switch (view with front fascia removed)
Component Description
ITS control unit • Being connected with rear view camera via ITS communication, receives vehicle detection signal
and transmits Blind Spot Warning indicator signal and Blind Spot Warning indicator dimmer sig-
nal to the rear view camera
• Being connected with lane camera unit via ITS communication, receives detected lane condition
signal
• Receives steering angle sensor signal from steering angle sensor via CAN communication
• Judges a Blind Spot Warning indicator ON/OFF state and an approach state to the lane marker,
based on each signal.
• Activates the warning buzzer and warning systems ON indicator
• Transmits Blind Spot Warning ON indicator signal to combination meter via CAN communication
Blind Spot Warning indicator LH/
RH Receives Blind Spot Warning indicator operation signal from rear view camera and turns OFF, turns
ON or blinks
Warning systems switch Inputs the switch signal to ITS control unit
Warning systems ON indicator
(On the warning systems switch) Indicates BSW system status
Rear view camera • Detects the lane marker by the built-in camera
• Transmits detected lane condition signal to ITS control unit
ABS actuator and electric unit
(control unit) • Transmits vehicle speed signal to ITS control unit via CAN communication
• Transmits yaw rate signal/side G sensor signal to ITS control unit via CAN communication
Buzzer (combination meter) Receives buzzer signal from ITS control unit and sounds buzzer.
Combination meter • Turns the Blind Spot Warning indicator ON/OFF according to the signals from the ITS control unit
via CAN communication
• Receives Blind Spot Warning ON indicator signal via CAN communication.
Steering angle sensor Transmits steering angle sensor signal to ITS control unit via CAN communication
BCM • Transmits turn signal indicator to ITS control unit via CAN communication
• Transmits dimmer signal to ITS control unit via CAN communication
ECM Transmits engine speed signal to ITS control unit via CAN communication
TCM Transmits the output shaft speed signal, input speed signal, current gear position signal and shift
position signal to ITS control unit via CAN communication
AV c o n t r o l u n i t
(with navigation system and bose
audio system) Receives the various systems and camera signals via CAN communication and routes them to the
center display
Audio unit
(with display audio system and
bose audio system) Receives the various systems and camera signals and routes them to the center display
Center display Displays the various system screen signals according to the priority level received via CAN com-
munication
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
SYSTEM
DAS-153
< SYSTEM DESCRIPTION >[BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
FUNCTION DESCRIPTION
• The BSW system can help alert the driver of ot her vehicles in adjacent lanes when changing lanes.
• The BSW system uses rear view camera near the rear bumper to detect vehicles in an adjacent lane.
• The rear view camera can detect vehicles on either si de of vehicle within the detection zone shown as illus-
trated.
• This detection zone starts from the back of the v ehicle and extends approximately 3.0 m (10 ft) behind the
rear bumper, and approximately 13.0 m (10 ft) sideways.
• The BSW system operates above approximately 32 km/h (20 MPH).
• If the rear view camera detects vehicles in the detec tion zone, the Blind Spot Warning indicator illuminates.
• If the driver then activates the turn signal, a buzzer will sound twice and the Blind Spot Warning indicator will blink.
NOTE:
A buzzer sounds if the rear view camera has already detected vehicles when the driver activates the turn
signal. If a vehicle comes into the detection zone after t he driver activates the turn signal, then only the Blind
Spot Warning indicator blinks and no buzzer sounds.
BSW SYSTEM OPERATION DESCRIPTION
• Control unit enables BSW system.
• The control unit turns on the BSW system w hen the warning systems switch is turned ON.
• Rear view camera detects a vehicle in the adjacent l ane, and transmits the vehicle detection signal to control
unit.
• Control unit starts the control as follows, based on a vehicle detection signal, turn signal and dimmer signal transmitted from BCM via CAN communication:
- Blind Spot Warning indicator signal and Blind Spot Warning indicator dimmer signal transmission to rear view camera.
- Buzzer signal transmission to warning buzzer.
• Rear view camera transmits an indicator operation signal to the Blind Spot Warning indicator according to
Blind Spot Warning indicator signal and Blind Spot Warning indicator dimmer signal.
Operation Condition of BSW System
JSOIA0257GB
JSOIA0258GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-154
< SYSTEM DESCRIPTION >[BSW]
SYSTEM
control unit performs the control when the following conditions are satisfied:
• When the warning systems switch is turned ON
*.
• When the vehicle drives at 32 km/h (20 MPH) or more in the forward direction.
NOTE:
*: When the BSW system setting on the v ehicle information display screen is ON.
• After the operating conditions of warning are satisf ied, the warning continues until the vehicle speed is
reduced below approximately 29 km/h (18 MPH)
• The BSW system may not function properly, depending on the situation.
BULB CHECK ACTION AND FAIL-SAFE INDICATION
*: Blinking cycle when there is a rear view camera blockage condition or lane camera unit high tempera-
ture condition
NOTE:
Time shown in the figure is approximate.
Fail-safe (ITS Control Unit)INFOID:0000000009464808
If a malfunction occurs in each system, ITS control uni t cancels each control, and turns ON the warning lamp
or indicator lamp.
Vehicle condition/Driver ′s operation Blind Spot Warning/
Blind Spot Intervention indicator Warning systems
ON indicator Indication on the combination meter
When DTC is detected OFF ON OFF
→ Orange
Temporary disabled status OFF ON BSW light (white) will blink
When rear view camera needs cleaning OFF ON Unavailable: Clean Rear Camera
When the warning systems switch is
pressed
(When the settings of LDW system and
BSW system on the vehicle information
screen are “OFF”) OFF Blink —
ALOIA0172GB
JSOIA0358GB
System Warning lamp/Indicator lamp Description
Blind Spot Warning (BSW) Blind Spot Warning lamp Cancel
Lane Departure Warning (LDW) Lane Departure Warning indicator Cancel
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
OPERATIONDAS-155
< SYSTEM DESCRIPTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
OPERATION
Switch Name and FunctionINFOID:0000000009464809
System Display and WarningINFOID:0000000009464810
INDICATOR AND WARNING LAMP
DISPLAY AND WARNING OPERATION
ALOIA0109ZZ
No. Name Function 1 Warning systems switch Turns BSW system ON/OFF
(When the setting of BSW system on the vehicle information display setting screen
is ON)
ALOIA0180ZZ
No. Name Description
1 Warning systems ON indicator Indicates that the LDW system and/or BSW system is ON
2 Blind Spot Warning lamp (orange) • Turns ON when Blind Spot Warning system is malfunctioning
• Blinks during the following conditions:
- DTC is detected or system is temporarily disabled.
- When rear view camera blockage is detected.
Vehicle condition/ Driver's operation Action
Warning
systems ON indicator Vehicle speed
(Approx.)
[km/h (MPH)] Turn signal
condition Status of ve-
hicle detec- tion within detection
area Indication on the
Blind Spot Warning indicator Buzzer
OFF — — — OFF OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM