2014 MITSUBISHI OUTLANDER SPORT key

Security alarm system*
Locking and unlocking 4-25
4
(The buzzer sounds intermittently and thesecurity indicator (A) blinks.)
The system preparation time extends from thepoint at which all of the doors and the tailgateare locked by pressing of the LOCK switchon the remote control switch or the keylessoperation function to the point at which thesystem armed mode goes into effect.During this time, it is possible to temporarilyopen a door or the tailgate without using thekeyless entry system or the keyless operationfunction and without causing the alarm tosound (for example, when you forget some-thing inside the vehicle or realize that a win-dow is open).(The buzzer stops and the security indicatorcontinues to blink with the indicator’sreduced lit-up duration time.)Once the system preparation mode has ended,the system armed mode starts.
zIf the turn-signal lamps do not blink after thelocking and unlocking operation using thekeyless entry system or
the keyless operation
function, the security alarm system may bemalfunctioning.Have the vehicle inspected at aMITSUBISHI MOTORS Authorised ServicePoint.If the confirmation function (blinking of theturn-signal lamps by
locking and unlocking
the doors and the tailgate) is deactivated, theturn-signal lamps do not blink after the lock-ing and unloc
king operation.
For information on the confirmation func-tion, refer to “Keyless entry system” onpages 4-3 and “To opera
te using the keyless
operation function”
on page 4-9.
zThe security alarm system could be activatedin the following situations.•Using a car washer•Taking the vehicle on a ferry•Parking in an automated car park•Leaving someone or a pet in the vehicle•Leaving a window or the sunroof open• Leaving an unstable object such as a stuffedtoy or accessory in the vehicle• Suffering a continuous impact or vibrationby hail, thunder, etc.NOTE
• Air flows by the Remote Climate Control.According to the situations, please deacti-vate the vehicle inclination detection func-tion and the interior intrusion detectionfunction.Refer to “To deactivate the vehicle inclina-tion detection function and the interiorintrusion detection f
unction” on page 4-27.
zThe sensitivity of the interior intrusiondetection function can be adjusted. For fur-ther details, please contact a MITSUBISHIMOTORS Authorised Service Point.
The security alarm has four modes:

System preparation mode (approx. 20 seconds)

NOTE
System armed mode

BK0203201EN.book 25 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*4-26 Locking and unlocking
4
If an unlawful opening of any of the doors,tailgate or bonnet is detected during the sys-tem armed mode, the alarm will be activatedto warn people around the vehicle of anabnormal condition.Inside alarm (approx. 10 seconds):
The buzzer sounds, warning those insidethe vehicle of an abnormal condition.(except for vehicles equipped with theinterior alarm sensor)
Outside alarm (approx. 30 seconds):
The turn-signal lamps blink and the horn(the siren for vehicles equipped with theinterior alarm sensor) sounds, warningpeople around the vehicle of an abnormalcondition.
Refer to “Alarm activation” on page 4-28.
It is possible to cancel the system activationduring the system preparation mode or thesystem armed mode.In addition, it is possible to cancel the alarmonce it has been activated.Refer to “Cancelling the system” on page4-28, “Cancelling the alarm” on page 4-29.
E00301701988
Follow the procedure be
low to set the system
to the system armed mode.1. Put the operation mode in OFF.2. Exit the vehicle and close all of the doors,tailgate and bonnet.
3. Press the LOCK switch (A) on the remotecontrol switch of the keyless operationkey, the driver’s or front passenger’s doorlock/unlock switch (B), or the tailgateLOCK switch (C) in order to lock all thedoors and the tailgate.
Alarm activation

NOTE
zThe alarm will resume if unlawful actionsare taken again, even if the alarm hasstopped.
System cancellation

NOTE
zWhen lending the vehicle to another personor allowing the vehicle to be driven by some-one who is unfamiliar with the security alarmsystem, be sure to give the person a properexplanation of the se
curity alarm system.
If a person who is unfamiliar with the secu-rity alarm system accidentally unlocked thevehicle, causing the alarm to sound, thealarm would be a nuisance to people nearby.
Setting the system

Driver’s and front passenger’s door lock/unlock switches
*
BK0203201EN.book 26 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*
Locking and unlocking 4-27
4
By locking the vehicle using the keylessentry system or the keyless operationfunction, the system preparation mode isactivated.The buzzer makes an intermittent beepingsound and the security indicator (D) in thecentre panel flashes for confirmation.
4. After approximately 20 seconds, thebuzzer stops, and when the blinking of thesecurity indicator starts to slow down, thesystem armed mode goes into effect.The security indicator continues to blinkduring the system armed mode.
E00312101416
The vehicle inclination detection function andthe interior intrusion detection function canbe deactivated when parking in automated carparks or leaving pets in the vehicle or leavingthe vehicle with the windows slightly open.1. Put the operation mode in OFF.2. Raise and hold the wiper and washerswitch to the “MIST” position for about 3seconds. The buzzer will sound once andthe function will be deactivated.
To a c t i v a t e t h e f u n c t i o n a g a i n , r a i s e a n d h o l dthe wiper and washer switch to the “MIST”position for about 3 seconds.The buzzer will sound twice and the functionwill be activated.
Ta i l g a t e L O C K s w i t c h
*
NOTE
zThe system preparation mode is not activatedwhen the doors and the tailgate have beenlocked using a method ot
her than the keyless
entry system or the keyless operation func-tion (namely a key, the inside lock knob orthe central door lock switch).zIf the bonnet is open, the security indicatorilluminates, and the system does not enterthe system preparation mode.When the bonnet is closed, the system entersthe system preparation mode, and after about20 seconds the system enters the systemarmed mode.NOTE
zThe security alarm system can be activatedwhen people are riding inside the vehicle orwhen the windows are open. To prevent acci-dental activation of the alarm, do not set thesystem to the system armed mode while peo-ple are riding in the vehicle.zAv o i d l e a v i n g v a l u a b l e i t e m s i n s i d e t h e v e h i -cle even when the secu
rity alarm system has
been set to the “active” mode.
To d e a c t i v a t e t h e v e h i c l e i n c l i n a -tion detection function and the interior intrusion detection func-tion

BK0203201EN.book 27 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Security alarm system*4-28 Locking and unlocking
4
E00301801859
The following methods can be used to cancelthe system when it is in the system prepara-tion mode or the system armed mode.zPressing the UNLOCK switch on theremote control switch.zPutting the operation mode in ON.zOpening any one of the doors or the tail-gate, when the system is in the systempreparation mode.
zHolding the keyless operation key andpressing the driver’s or front passenger’sdoor lock/unlock switch, or the tailgateopen switch to unlock the doors and thetailgate.
E00301902118
When the system is in the system armedmode, the alarm will be activated as followsif the vehicle is unlocked or if any of thedoors, tailgate or bonnet is opened using amethod other than the keyless entry system orthe keyless operation function.
NOTE
The function will be activated again if the fol-lowing operation is performed.zIf the doors and the tailgate are unlockedusing the keyless entry
system or the keyless
operation function.zIf the operation mode is put in on or ACC.
Cancelling the system

NOTE
zIf the bonnet is opened during the systempreparation mode, the system preparationmode is suspended.The system returns to the system preparationmode when the bonnet is closed.zIf the battery terminals are disconnectedwhile the system is in
the system preparation
mode, the memory will be erased.zIt is possible to regist
er up to 4 remote con-
trol switches.As long as they are registered, any of theremote control switches, other than the oneused to activate the system, can be used tocancel the system.If you want to register additional remotecontrol switches, please contact aMITSUBISHI MOTORS Authorised ServicePoint.zThe activation distance for keyless entry sys-tem is approximately 4 m.If it is not possible to lock or unlock thevehicle by pressing the switch at the correctdistance or the security alarm system cannotbe set or cancelled using the switch, the bat-tery may need to be replaced.Replace the battery at a MITSUBISHIMOTORS Authorised Service Point.
zIf the UNLOCK switch on the remote con-trol switch, or the driver’s or front passen-ger’s door lock/unlock switch is pressed andno door or the tailgate is opened within 30seconds, the doors and the tailgate will auto-matically relock. In this
case as well, the sys-
tem preparation mode will go into effect.zThe time between pressing of the UNLOCKswitch on the remote control switch, or thedriver’s or front passenger’s doorlock/unlock switch and automatic lockingcan be adjusted. Please consult aMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped with Mitsubishi Multi-Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
Alarm activation

NOTE
BK0203201EN.book 28 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Electric window control
Locking and unlocking 4-29
4
1. The inside alarm will be activated forapproximately 10 seconds. (except forvehicles equipped with the interior alarmsensor)2. The alarm will be activated for approxi-mately 30 seconds.The turn-signal lamps will flash, and thehorn (the siren for vehicles equipped withthe interior alarm sensor) will sound inter-mittently.3. The alarm will resume if unlawful actionsare taken again, even if the alarm hasstopped.
E00302001698
It is possible to halt the activation of an alarmusing the following methods:zPressing the LOCK or UNLOCK switchon the remote control switch.(After pressing of the LOCK switch, thevehicle will lock if all the doors and thetailgate are closed, after which the systempreparation mode will once again go intoeffect.)zPutting the operation mode in ON.zHolding the keyless operation key andlocking or unlocking the doors and thetailgate using the keyless operation func-tion.
E00302201632
The electric windows can only be operatedwith the operation mode in ON.
E00302301822
Each door window opens or closes while thecorresponding switch is operated.
NOTE
zIf the bonnet is opened during the systemarmed mode, the vehicl
e outside alarm oper-
ates immediately.
Cancelling the alarm

NOTE
zWhen the ignition switch is turned to the“ON” position or the operation mode is putin ON, the buzzer sounds 4 times. This oper-ation indicates that the alarm was activatedwhile the vehicle was parked.Please check the inside of the vehicle to con-firm that nothi
ng was stolen.
zEven if the battery is disconnected, the alarmactivation memory will not be erased.
Electric window control Electric window control switch 1- Driver’s door window2- Front passenger’s door window3- Rear left door window4- Rear right door window5- Lock switchDriver’s switchLHD
Driver’s switchRHD
BK0203201EN.book 29 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Electric window control4-30 Locking and unlocking
4
The driver’s switches can be used to operateall door windows. A window can be openedor closed by operating the correspondingswitch.Press the switch down to open the window,and pull up the switch to close it.If the switch for the driver’s window is fullypressed down/pulled up, the door windowautomatically opens/closes completely.If you want to stop the window movement,operate the switch lightly in the reverse direc-tion.
The passenger’s switches can be used to oper-ate the corresponding passenger’s door win-dows.Press the switch down for opening the win-dow, and pull up the switch for closing.
E00303101263
When this switch is operated, the passenger’sswitches cannot be used to open or close the
door windows and the driver’s switch cannotopen or close any door windows other thanthe driver’s door window.To u n l o c k , p r e s s i t o n c e a g a i n .
E00302401012
The door windows can be opened or closedfor 30 seconds after the engine is stopped.
WA R N I N GzBefore operating the electric window con-trol, make sure that nothing is capable ofbeing trapped (head, hand, finger, etc.).zNever leave the vehicle without removingthe key.zNever leave a child (or other person whomight not be capable of safe operation ofthe electric window control) in the vehiclealone.
Driver’s switches
Passenger’s switches
NOTE
zRepeated operation with the engine stoppedwill run down the battery. Operate the win-dow switches only while
the engine is run-
ning.zThe rear door windows only open halfway.
Lock switch
1- Lock2- UnlockWA R N I N GzA child may tamper with the switch at therisk of its hands or head being trapped inthe window. When driving with a child inthe vehicle, please press the window lockswitch to disable the passenger’s switches.
Timer function
BK0203201EN.book 30 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Sunroof*4-32 Locking and unlocking
4
When the switch (2) is pressed, the rear edgeof the sunroof rises for ventilation.The sunroof tilts down while the switch (3) ispressed.
E00303900349
The sunroof can be opened or closed for 30seconds after the ignition switch is turnedfrom the “ON” position to the “ACC” or“LOCK” position.However, once the driver’s door or the frontpassenger’s door is opened, the sunroof can-not be operated.
E00304100029
Slide the sunshade manually to open andclose it.
To t i l t u p

To t i l t d o w n

Timer function

WA R N I N GzBefore operating the sunroof, make surethat nothing is capa
ble of being trapped
(head, hand, finger, etc.).zDo not put head, hands or anything elseout of the sunroof opening while drivingthe vehicle.zNever leave the vehicle without removingthe key.
zNever leave a child (o
r other person who
might not be capable of safe operation ofthe sunroof switch) in the vehicle alone.NOTE
zThe sunroof stops just before reaching thefully open position.If the vehicle is driven with the sunroof inthis position, wind buffeting is lower thanwith the sunroof fully open.zWhen leaving the vehicle unattended, makesure you close the sunroof and remove theignition key.zDo not try to operate the sunroof if it is fro-zen closed (after snow fall or during extremecold).zDo not sit or place heavy luggage on the sun-roof or roof opening edge.zRelease the switch as
soon as the sunroof
reaches the fully open or fully closed posi-tion.zIf the sunroof does not operate when the sun-roof switch is operated, release the switchand check whether something is trapped bythe sunroof. If nothing is trapped, have thesunroof checked at an authorized MITSUBI-SHI MOTORS dealer.zDepending on the models of ski carriers orroof carriers, the sunroof may contact thecarrier when the sunroof is tilted up. Be care-ful when tilting up the sunroof if such a skicarrier or a roof carrier is installed.WA R N I N G
zBe sure to close the sunroof completelywhen washing the vehicle or when leavingthe vehicle.zBe careful not to put any wax on the weath-erstrip (black rubber) around the sunroofopening. If stained with wax, the weather-strip cannot maintain a weatherproof sealwith the sunroof.zAfter washing the vehicle or after it hasrained, wipe off any water that is on the sun-roof before operating it.zOperating the sunroof
repeatedly with the
engine stationary will run down the battery.Operate the sunroof while the engine is run-ning.
Sunshade

NOTE
BK0203201EN.book 32 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Seat belts
Seat and seat belts 5-13
5
3. Insert the latch plate (B) into the buckle(D).4. Pull the belt slightly to adjust slackness asdesired.1. Hold the latch plate and push the buttonon the buckle.
2. After the seat belt is retracted completely,insert the latch plate (B) into the upper slit(F), and then insert the small latch plate(A) into the lower slit (G).3. Store the seat belt buckle in the storagepocket.(Refer to next column.)
E00405301521
When the seat belt is not in use, store it asshown in the illustration.After passing the belt through the rear notch(A), insert the plate into the front notch (B).
To u n f a s t e n
NOTE
zAs the belt retracts au
tomatically, keep the
latch plate held while retracting so that thebelt stows slowly. Failure to do this coulddamage the vehicle.zTo r e l e a s e t h e b u c k l e ( C ) , p r e s s t h e b u t t o n(E) with a narrow-tipped object (latch plateor mechanical key etc.).
Rear seat belt storage Seat belt plate storage Outboard seating position
BK0203201EN.book 13 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分