2014 MITSUBISHI OUTLANDER SPORT service indicator

Indicator lamp, warning lamp, and information screen display list6-22 Instruments and controls
6
E00523901344
When there is information to be announced, such as lamp reminder, the buzzer sounds and the screen switches to the displays sho
wn below. Refer
to the appropriate page and take the necessary measures.When the cause of the warning display is eliminated, the warning display goes out automatically.Refer to “Warning display list” on page 6-22.Refer to “Navigation information display” on page 6-32.Refer to “Other interrupt displays” on page 6-33.
E00524001993
19- Information screen display list
m P. 6-22
Information screen display list
NOTE
zA warning may be displayed on the in
formation screen and the buzzer ma
y sound in the following rare cases.
This is caused by the system picking up inte
rference such as noise or strong electromagnetic waves, and is not a functional pro
blem.
•An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a rad
ar station.
•Abnormal voltage or a static electricity
discharge is generated by th
e operation of installed elect
rical equipment (including
after-market parts).
If the warning display appears many times,
we recommend you to consult a MITSUBISHI MOTORS Authorised Service Point.
Warning display li st
Screen
Cause
Solution (Reference)
zOne or more minor failure is occurring in the Plug-in Hybrid EV System.
zHave your vehicle inspected by a MIT-SUBISHI MOTORS Authorised Service Point.
BK0203201EN.book 22 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list
Instruments and controls 6-23
6
zOne or more failure is occurring in the Plug-in Hybrid EV System.
zImmediately park the vehicle in a safe place and contact a MITSUBISHI MOTORS Authorised Service Point.
zThe parking lock unit is in failure. The Plug-in Hybrid EV system cannot be kept in standstill condition without applying the parking brake.
zPark the vehicle at a safe, flat place and apply the parking brake. Contact a MIT-SUBISHI MOTORS Authorised Service Point.Refer to “Electrical parking switch” on page 7-16.
zYo u a r e a t t e m p t i n g t o s e t t h e o p e r a t i o n mode to “ON” when the charge connector is connected to the charge port.
zDisconnect the charge connector from the charge port before operating the power switch.
zCharging was interrupted due to system failure (electric leak detected).
zThere is an electric leak or the normal charge cable is faulty. Immediately stop using the cable and contact a MITSUBI-SHI MOTORS Authorised Service Point.
zCharging was interrupted due to poor con-nection of the charge cable or power fail-ure.
zConnect the charge cable correctly.Refer to “Normal charging” on page 3-8.zIf charging is interrupted due to a power failure, charging will be automatically resumed when the power is restored.
Screen
Cause
Solution (Reference)
BK0203201EN.book 23 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-24 Instruments and controls
6
zThe drive battery temperature is too cold.
zWhen the vehicle is under running, stop the vehicle at a safe place and contact a MIT-SUBISHI MOTORS Authorized Service Point.zWhen the vehicle is in parking, in the day-time, wait for the outside temperature to rise and re-start the Plug-in hybrid system if the outside temperature has been risen.Refer to “Cautions and actions to deal with intense cold” on page 2-9.
zYo u h a v e f o r g o t t e n t o t u r n o f f t h e l a m p s . R e f e r t o “ L a m p s ( h e a d l a m p s , f o g l a m p , e t c . )
auto-cutout function” on page 6-40.
zThere is a fault in the keyless operation system.
Refer to “Keyless operation system” on page 4-6.
Screen
Cause
Solution (Reference)
BK0203201EN.book 24 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Indicator lamp, warning lamp, and information screen display list6-26 Instruments and controls
6
zThe RBS (regenerative brake system) can-not be used.
zWe recommend you to consult a MITSUB-ISHI MOTORS Authorised Service Point.
zThere is a fault in the ABS.
zAv o i d s u d d e n b r a k i n g a n d h i g h - s p e e d d r i v -ing, stop the vehicle in a safe place, and take corrective measures. Refer to “ABS warning” on page 7-30.
zOne of the doors or the tailgate is not com-pletely closed.The open door is displayed.
zClose the door or tailgate.Refer to “Door ajar warning display screen” on page 6-9.
zThe bonnet is open.
zClose the bonnet.Refer to “Bonnet” on page 11-3.
zThere is a fault in the electronic immobi-lizer (Anti-theft starting system).
zPut the operation mode in OFF, and then start the Plug-in Hybrid EV System again.If the warning is not cancelled, please con-tact a MITSUBISHI MOTORS Authorised Service Point.
Screen
Cause
Solution (Reference)
BK0203201EN.book 26 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Information screen display
Instruments and controls 6-39
6
E00502702287
This warning lamp will illu-minate when there is a prob-lem with the charging systemfor the auxiliary battery.Normally, when the operation
mode of the power switch is put in ON, thiswarning lamp will illuminate. Then, when thePlug-in Hybrid EV System is started and theready indicator illuminates, the warning lampwill go out.
E00537300023
This warning lamp will illu-minate when there is a fault atthe Plug-in Hybrid EV Sys-tem.Refer to “Service precautions”
on page 11-2.Normally, this warning lamp illuminateswhen the operation mode of the power switchis put in ON, and goes off after a few seconds.
E00537200022
This warning lamp will illu-minate when there can notused at the regenerative brakewhile the Plug-in Hybrid EVSystem is operating.
The warning is also displayed on the multiinformation display.
Normally, this warning lamp illuminateswhen the operation mode of the power switchis put in ON, and goes off after the Plug-inHybrid EV System is activated.
E00524601117E00524701381
This warning is displayed if you drive withthe parking brake still applied. The warninglamp in the instrument cluster only illumi-nates when the parking brake is applied.
Auxiliary battery charge warn-ing lamp
CAUTIONzIf the warning lamp stays on after the readyindicator illuminates, there may be a prob-lem with the charging system for the auxil-iary battery.•Immediately park your vehicle in a safeplace and we recommend you to have itchecked.•Do not charge the auxiliary battery.
Plug-in Hybrid EV System warning lamp
CAUTIONzIf the lamp illuminates while the Plug-inHybrid EV System is
operating, immediately
park your vehicle in a safe place and we rec-ommend you to consult a MITSUBISHIMOTORS Authorised Service Point.
Regenerative brake warning lamp
CAUTIONzIf the lamp illuminates while the Plug-inHybrid EV System is
operating, we recom-
mend you to have the vehicle inspected by aMITSUBISHI MOTORS Authorised ServicePoint.
Information screen display Brake warning display
BK0203201EN.book 39 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Combination headlamps and dipper switch6-42 Instruments and controls
6
zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will turn off automaticallywhen the driver"s door is opened.zIf the operation mode of the power switchis put in OFF or ACC while the lampswitch is in the “ ” or “ ” position,the lamps will remain on for about 3 min-utes while the driver’s door is shut andwill then automatically turn off.
1. Turn the lamp switch in the “OFF” posi-tion while the operation mode of thepower switch is in OFF or ACC.2. Turn on the lamps with the switch in the“ ” or “ ” position again, then thelamps will remain on.3. When 1 minute has passed, the lamps willautomatically be turned off.
E00506101631
If the driver’s door is opened when the opera-tion mode of the power switch is put in ACCor OFF with the lamps illuminated, a buzzerwill sound to remind the driver to turn off thelamps.The buzzer will automatically stop if theauto-cutoff function is activated, the lampswitch is turned off, or the door is closed.
E00506201544
When the lamp switch is in the “ ” posi-tion, the beam changes from high to low (orlow to high) each time the lever is pulledfully (1). While the high beam is on, the highbeam indicator lamp in the instrument clusterwill also illuminate.
E00506300199
The high beams flash when the lever is pulledslightly (2), and will go off when it isreleased.When the high beam is on, the high beamindicator lamp in the instrument cluster willilluminate.
Lamps (headlamps, fog lamp, etc.) auto-cutout function
NOTE
zThe lamp auto-cutout function can also bedisabled.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
When you want to keep the lamps on:
NOTE
zIf you place the light switch in the “ ”position, the lamps will not be automaticallyturned off.
Lamp monitor buzzer
Dipper (High/Low beam change) Headlamp flasher
BK0203201EN.book 42 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Turn-signal lever
Instruments and controls 6-45
6
E00506502645
E00506602024
Use the hazard warning flasher switch whenthe vehicle has to be parked on the road forany emergency.The hazard warning flashers can always beoperated, regardless of the operation mode.Push the switch to turn on the hazard warningflashers, all turn signal lamps flash continu-ously. To turn them off, push the switchagain.
Tu r n - s i g n a l l e v e r 1- Turn-signals
When making a normal turn, use position(1). The lever will return automaticallywhen cornering is completed.
2- Lane-change signals
When moving the lever to (2) slightly tochange a lane, the turn-signal lamps andindicator lamp in the instrument clusterwill only flash while the lever is oper-ated.Also, when you move the lever to (2)slightly then release it, the turn-signallamps and indicator lamp in the instru-ment cluster will flash three times.
NOTE
zIf the lamp flashes unusually quickly, thebulb in a turn-signal lamp may have burnedout. We recommend you to have the vehicleinspected.zIt is possible to activate the following func-tions:•Flashing of the turn-signal lamps when thelever is operated with the operation mode isin ACC.•Deactivate the turn-signal lamp 3-flashfunction for lane changes•The time required to operate the lever forthe 3-flash function can be adjusted.For further information, we recommend youto consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.zIt is possible to change the tone of a sound-ing buzzer as the turn-signal lamps flash.Refer to “Changing the turn-signal sound”on page 6-20.
Hazard warning flasher switch
NOTE
zIf the switch is used for a long period whilethe ready indicator is not illuminated, theauxiliary battery coul
d go flat and the Plug-
in Hybrid EV System could be impossible tostart.
BK0203201EN.book 45 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

ECO mode switch6-46 Instruments and controls
6
E00531801049
ECO mode is an eco-driving support systemwhich automatically controls the Plug-inHybrid EV System and air conditioning sys-tem to improve fuel efficiency.Refer to “Automatic climate control air con-ditioner” on page 8-4.The ECO mode starts working by pressingthe ECO mode switch when operation modeof the power switch is in ON. Push the switchagain and the ECO mode will cancel.While the ECO mode is working, an ECOmode indicator will be turned on.
E00506700034E00508301741
The front fog lamps can be operated while theheadlamps or tail lamps are on. Turn the knobin the “ON” direction to turn on the front foglamps. An indicator lamp in the instrumentcluster will also come on. Turn the knob inthe “OFF” direction to turn off the front foglamps. The knob will automatically return toits original position when you release it.
zOn vehicles equipped with the emergencystop signal system, while the hazard warninglamps are blinking due to having manuallypushed the switch, the emergency stop signalsystem does not operate.Refer to “Emergency stop signal system” onpage 7-29.
ECO mode switch
NOTE
NOTE
zEven if the ECO mode is operating, you canselect normal operation of the air condi-tioner.For further informati
on, we recommend you
to consult a MITSUBISHI MOTORSAuthorised Service Point.On vehicles equipped
with Mitsubishi Multi-
communication System (MMCS), it is possi-ble to change the setting by means of screenoperations.Refer to the separate owner’s manual fordetails.
Fog lamp switch Front fog lamp switch LHD/RHD (Type 1)
BK0203201EN.book 46 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分