2012 Lancia Voyager Owner handbook (in English)

to enter the name or number and say
the name of the phonebook entry you
wish to send. The Uconnect™ Phone
will then send the corresponding
phone number associated with the
phonebook entry, as tones over the
phone.
NOTE:
 You may not hear all of the tonesdue to mobile phone network
configurations; this is normal.
 Some paging and voice mail sys- tems have system time out set-
tings that are too short and may
not allow the use of this feature.
Barge In — Overriding Prompts
The “Voice Command” button can be
used when you wish to skip part of a
prompt and issue your voice com-
mand immediately. For example, if a
prompt is asking “Would you like to
pair a phone, clear a…,” you could
press the
button and say, “Pair
a Phone” to select that option without
having to listen to the rest of the voice
prompt. Turning Confirmation Prompts
On/Off
Turning confirmation prompts off
will stop the system from confirming
your choices (e.g., the Uconnect™
Phone will not repeat a phone number
before you dial it).
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say:
“Setup Confirmations Prompts On”
“Setup Confirmations Prompts Off”
Phone And Network Status
Indicators
If available on the radio and/or on a
premium display such as the instru-
ment panel cluster, and supported by
your mobile phone, the Uconnect™
Phone will provide notification to in-
form you of your phone and network
status when you are attempting to
make a phone call using Uconnect™
Phone. The status is given for network
signal strength, phone battery
strength, etc. Dialing Using The Mobile Phone
Keypad
You can dial a phone number with
your mobile phone keypad and still
use the Uconnect™ Phone (while di-
aling via the mobile phone keypad,
the user must exercise caution and
take precautionary safety measures).
By dialing a number with your paired
Bluetooth® mobile phone, the audio
will be played through your
vehicle's
audio system. The Uconnect™ Phone
will work the same as if you dialed the
number using a Voice Command.
NOTE:
Certain brands of mobile phones
do not send the dial ring to the
Uconnect™ Phone to play it on the
vehicle audio system, so you will
not hear it. Under this situation,
after successfully dialing a num-
ber the user may feel that the call
did not go through even though the
call is in progress. Once your call is
answered, you will hear the audio.
Mute/Un-Mute (Mute Off)
When you mute the Uconnect™
Phone, you will still be able to hear
the conversation coming from the
91

other party, but the other party will
not be able to hear you. In order to
mute the Uconnect™ Phone:
 Press the
button.
 Following the beep, say “Mute”.
In order to un-mute the Uconnect™
Phone:
 Press thebutton.
 Following the beep, say “Mute off”.
ADVANCED PHONE
CONNECTIVITY
Transfer Call To And From
Mobile Phone
The Uconnect™ Phone allows ongo-
ing calls to be transferred from your
mobile phone to the Uconnect™
Phone without terminating the call.
To transfer an ongoing call from your
Uconnect™ Phone paired mobile
phone to the Uconnect™ Phone or
vice versa, press the
button and
say “Transfer Call”. Connect Or Disconnect Link
Between The Uconnect™ Phone
And Mobile Phone
Your mobile phone can be paired with
many different electronic devices, but
can only be actively "connected" with
one electronic device at a time.
If you would like to connect or discon-
nect the Bluetooth® connection, your
mobile phone, and the Uconnect™
phone system, follow the instructions
described in your mobile phone
User's
Manual.
List Paired Mobile Phone Names
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Setup Phone
Pairing”.
 When prompted, say “List Phones”.
 The Uconnect™ Phone will play the phone names of all paired mo-
bile phones in order from the high-
est to the lowest priority. To “se-
lect” or “delete” a paired phone
being announced, press the
button and say “Select” or “De- lete”. Also, see the next two sections
for an alternate way to “select” or
“delete” a paired phone.
Select Another Mobile Phone
This feature allows you to select and
start using another phone paired with
the Uconnect™ Phone.
 Press the
button to begin.
 After the “Ready” prompt and the following beep, say “Setup Select
Phone” and follow the prompts.
 You can also press the
button
at any time while the list is being
played, and then choose the phone
that you wish to select.
 The selected phone will be used for the next phone call. If the selected
phone is not available, the
Uconnect™ Phone will return to
using the highest priority phone
present in or near (approximately
within 9 m) the vehicle.
Delete Uconnect™ Phone Paired
Mobile Phones
 Press the
button to begin.
92

 After the “Ready” prompt and thefollowing beep, say “Setup Phone
Pairing”.
 At the next prompt, say “Delete” and follow the prompts.
 You can also press the
button
at any time while the list is being
played, and then choose the phone
you wish to delete.
THINGS YOU SHOULD
KNOW ABOUT YOUR
UCONNECT™ PHONE
Uconnect™ Phone Tutorial
To hear a brief tutorial of the
Uconnect™ Phone features, press the
button and say “Uconnect™ Tu-
torial”.
Voice Training
For users experiencing difficulty with
the Uconnect™ Phone recognizing
their voice commands or numbers,
the Uconnect™ Phone Voice Training
feature may be used. To enter this
training mode, follow one of the two
following procedures:
From outside the Uconnect™ Phone
mode (e.g., from radio mode)  Press and hold the
button for
five seconds until the session be-
gins, or,
 Press the
button and say the
“Voice Training, System Training,
or Start Voice Training” command.
You can either press the Uconnect™
Phone button to restore the factory
setting or repeat the words and
phrases when prompted by the
Uconnect™ Phone. For best results,
the Voice Training session should be
completed when the vehicle is parked
with the engine running, all windows
closed, and the blower fan switched
off.
This procedure may be repeated with
a new user. The system will adapt to
the last trained voice only.
Reset
 press thebutton.
 After the “Ready” prompt, and the following beep, say “Setup”, then
“Reset”.
This will delete all phone pairing,
phone book entries, and other settings in all language modes. The System
will prompt you before resetting to
factory settings.
Voice Command
 For best performance, adjust the
rearview mirror to provide at least
1 cm gap between the overhead
console (for versions/markets,
where provided) and the mirror.
 Always wait for the beep before speaking.
 Speak normally, without pausing, just as you would speak to a person
sitting a few meters away from you.
 Make sure that no one other than you is speaking during a voice pe-
riod.
 Performance is maximized under:  low-to-medium blower setting,
 low-to-medium vehicle speed,
 low road noise,
 smooth road surface,
 fully closed windows,
 dry weather conditions.
93

 Even though the system is designedfor users speaking in European
English, Dutch, French, German,
Italian, or Spanish accents, the sys-
tem may not always work for some.
 When navigating through an auto- mated system such as voice mail, or
when sending a page, at the end of
speaking the digit string, make sure
to say “Send”.
 Storing names in the phonebook when the vehicle is not in motion is
recommended.
 It is not recommended to store simi- lar sounding names in the
Uconnect™ Phonebook.
 Phonebook (Downloaded and Uconnect™ Phone Local) recogni-
tion rate is optimized when the en-
tries are not similar.
 Numbers must be spoken in single digits. “800” must be spoken
“eight-zero-zero” not “eight hun-
dred”.
 You can say “O” (letter “O”) for “0” (zero).  Even though international dialing
for most number combinations is
supported, some shortcut dialing
number combinations may not be
supported.
 In a convertible vehicle, system per- formance may be compromised
with the convertible top down.
Far End Audio Performance
 Audio quality is maximized under:  low-to-medium blower setting,
 low-to-medium vehicle speed,
 low road noise,
 smooth road surface,
 fully closed windows,
 dry weather conditions, and
 operation from the driver seat.
 Performance, such as audio clarity, echo, and loudness to a large degree
rely on the phone and network, and
not the Uconnect™ Phone.
 Echo at the phone far end can sometimes be reduced by lowering
the in-vehicle audio volume.  In a convertible vehicle, system per-
formance may be compromised
with the convertible top down.
Recent Calls
If your phone supports “Automatic
Phonebook Download”, Uconnect™
Phone can list your Outgoing, Incom-
ing and Missed Calls.
SMS
Uconnect™ Phone can read or send
new messages on your phone.
Read Messages:
If you receive a new text message
while your phone is connected to
Uconnect™ Phone, an announcement
will be made to notify you that you
have a new text message. If you wish
to hear the new message:
 Press the
button.
 After the “Ready” prompt and the following beep, say “SMS Read” or
“Read Messages”.
 Uconnect™ Phone will play the new text message for you.
After reading a message, you can “Re-
ply” or “Forward” the message using
Uconnect™ Phone.
94

Send Messages:
You can send messages using
Uconnect™ Phone. To send a new
message:
 Press the
button.
 After the “Ready” prompt and the following beep, say “SMS Send” or
“Send Messages”.
 You can either say the message you wish to send or say “List Mes-
sages.” There are 20 preset mes-
sages.
To send a message, press the
button while the system is listing the
message and say “Send.”
Uconnect™ Phone will prompt you to
say the name or number of the person
you wish to send the message to.
List of Preset Messages:
1. Yes
2. No
3. Where are you?
4. I need more direction. 5. L O L
6. Why
7. I love you
8. Call me
9. Call me later
10. Thanks
11. See You in 15 minutes
12. I am on my way
13. I’ll be late
14. Are you there yet?
15. Where are we meeting?
16. Can this wait?
17. Bye for now
18. When can we meet
19. Send number to call
20. Start without me
Turn SMS Incoming Announcement
ON/OFF
Turning the SMS Incoming An-
nouncement OFF will stop the system
from announcing the new incoming
messages.
 Press the
button.
 After the “Ready” prompt and the following beep, say “Setup, Incom-
ing Message Announcement”, you
will then be given a choice to
change it.
Bluetooth® Communication Link
Mobile phones have been found to
lose connection to the Uconnect™
Phone. When this happens, the con-
nection can generally be reestablished
by switching the phone off/on. Your
mobile phone is recommended to re-
main in Bluetooth® ON mode.
Power-Up
After switching the ignition key from
OFF to either ON or ACC position, or
after a language change, you must
wait at least 15 seconds prior to using
the system.
95

96

97

98