2012 Lancia Voyager wiring

NOTE:
After any Active Hood deployment,
the vehicle should be taken to an
authorized dealer immediately.CAUTION!
To prevent possible damage, do not
slam the rear of the hood to reset it.
Press the rear of the hood down until
it is approximately 5 mm above the
fender. This should secure both hood
hinge reset mechanisms.WARNING!
 Ignoring the Air Bag WarningLight in your instrument panel or
the “SERVICE ACTIVE HOOD”
message in the EVIC could mean
you won’t have the Active Hood to
enhance pedestrian protection. If
the light does not come on as a
bulb check when the ignition is
first turned on, stays on after you
start the vehicle, or if it comes on
as you drive, see your authorized
dealer.
(Continued)
WARNING!(Continued)
 Modifications to any part of the
Active Hood system could cause it
to fail when you need it. Do not
modify the components or wiring.
Do not modify the front bumper,
vehicle body structure, or add an
aftermarket front bumper or
cover.
 It is dangerous to try to repair any
part of the Active Hood system
yourself. Be sure to tell anyone
who works on your vehicle that it
has an Active Hood system.
 Do not attempt to modify any part
of your Active Hood system. The
Active Hood may deploy acciden-
tally or may not function properly
if modifications are made. Take
your vehicle to an authorized
dealer for any hood service.
 Drivers must be aware of pedestri-
ans. Always be sure to check for
pedestrians, animals, other ve-
hicles, and obstructions. You are
responsible for safety and must
continue to pay attention to your
surroundings. Failure to do so can
result in serious injury or death. ENHANCED SEAT BELT
USE REMINDER SYSTEM
(BeltAlert®)
BeltAlert® is a feature intended to
remind the driver and front passenger
(for versions/markets, where pro-
vided with front passenger
BeltAlert®) to fasten their seat belts.
The feature is active whenever the
ignition is on. If the driver or front
seat passenger is unbelted, the Seat
Belt Reminder Light will turn on and
remain on until both front seat belts
are fastened.
The BeltAlert® warning sequence be-
gins after the vehicle speed is over
8 km/h, by blinking the Seat Belt
Reminder Light and sounding an in-
termittent chime. Once the sequence
starts, it will continue for the entire
duration or until the respective seat-
belts are fastened. After the sequence
completes, the Seat Belt Reminder
Light remains illuminated until the
respective seat belts are fastened. The
driver should instruct all other occu-
pants to fasten their seat belts. If a
front seat belt is unbuckled while
traveling at speeds greater than
43

If you do have a collision which de-
ploys the air bags, any or all of the
following may occur:
 The nylon air bag material maysometimes cause abrasions and/or
skin reddening to the driver and
front passenger as the air bags de-
ploy and unfold. The abrasions are
similar to friction rope burns or
those you might get sliding along a
carpet or gymnasium floor. They
are not caused by contact with
chemicals. They are not permanent
and normally heal quickly. How-
ever, if you haven't healed signifi-
cantly within a few days, or if you
have any blistering, see your doctor
immediately.
 As the air bags deflate, you may see some smoke-like particles. The
particles are a normal by-product
of the process that generates the
non-toxic gas used for air bag infla-
tion. These airborne particles may
irritate the skin, eyes, nose, or
throat. If you have skin or eye irri-
tation, rinse the area with cool wa-
ter. For nose or throat irritation,
move to fresh air. If the irritation continues, see your doctor. If these
particles settle on your clothing,
follow the garment manufacturer's
instructions for cleaning.
Do not drive your vehicle after the air
bags have deployed. If you are in-
volved in another collision, the air
bags will not be in place to protect
you.
WARNING!
Deployed air bags and seat belt pre-
tensioners cannot protect you in an-
other collision. Have the air bags,
seat belt pretensioners, and the
driver and front seat belt retractor
assemblies replaced by an autho-
rized dealer immediately. Also, have
the Occupant Restraint Controller
(ORC) system serviced as well. Maintaining Your Air Bag System
WARNING!
 Modifications to any part of the
air bag system could cause it to
fail when you need it. You could
be injured if the air bag system is
not there to protect you. Do not
modify the components or wiring,
including adding any kind of
badges or stickers to the steering
wheel hub trim cover or the upper
right side of the instrument panel.
Do not modify the front bumper,
vehicle body structure, or add af-
termarket side steps or running
boards.
 It is dangerous to try to repair any
part of the air bag system your-
self. Be sure to tell anyone who
works on your vehicle that it has
an air bag system.
(Continued)
51

WARNING!(Continued)
 Do not attempt to modify any part
of your air bag system. The air
bag may inflate accidentally or
may not function properly if
modifications are made. Take
your vehicle to an authorized
dealer for any air bag system ser-
vice. If your seat including your
trim cover and cushion needs to
be serviced in any way (including
removal or loosening/tightening
of seat attachment bolts), take the
vehicle to your authorized dealer.
Only manufacturer approved seat
accessories may be used. If it is
necessary to modify the air bag
system for persons with disabili-
ties, contact your authorized
dealer.
Air Bag Warning Light You will want to have the
air bags ready to inflate for
your protection in a colli-
sion. The Air Bag Warning
Light monitors the internal circuits
and interconnecting wiring associated
with air bag system electrical compo- nents. While the air bag system is
designed to be maintenance free, if
any of the following occurs, have an
authorized dealer service the air bag
system immediately.
 The Air Bag Warning Light does
not come on during the four to eight
seconds when the ignition switch is
first turned to the ON/RUN posi-
tion.
 The Air Bag Warning Light remains on after the four to eight-second
interval.
 The Air Bag Warning Light comes on intermittently or remains on
while driving.
NOTE:
If the speedometer, tachometer, or
any engine related gauges are not
working, the Occupant Restraint
Controller (ORC) may also be dis-
abled. The air bags may not be
ready to inflate for your protec-
tion. Promptly check the fuse
block for blown fuses. Refer to the
label located on the inside of the
fuse block cover for the proper air bag fuses. See your authorized
dealer if the fuse is good.
EVENT DATA RECORDER
(EDR)
This vehicle is equipped with an event
data recorder (EDR). The main pur-
pose of an EDR is to record, in certain
crash or near crash-like situations,
such as an air bag deployment or hit-
ting a road obstacle, data that will
assist in understanding how a vehi-
cle’s systems performed. The EDR is
designed to record data related to ve-
hicle dynamics and safety systems for
a short period of time, typically
30 seconds or less. The EDR in this
vehicle is designed to record such data
as:
 How various systems in your ve-
hicle were operating;
 Whether or not the driver and pas- senger safety belts were buckled/
fastened;
 How far (if at all) the driver was depressing the accelerator and/or
brake pedal; and,
 How fast the vehicle was traveling.52

Towing Requirements – Trailer
Lights And Wiring
Whenever you pull a trailer, regard-
less of the trailer size, stop lights and
turn signals on the trailer are required
for motoring safety.
The Trailer Tow Package may include
a seven-pin or a thirteen-pin wiring
harness. Use a factory approved
trailer harness and connector.
NOTE:
Do not cut or splice wiring into the
vehicles wiring harness.
The electrical connections are all
complete to the vehicle but you must
mate the harness to a trailer connec-
tor.
Seven - Pin Connector DetailsPin Function Wire
Color
1 Left Turn Signal Yellow
2 Rear Fog Light Blue
3 Ground/
Common Re-
turn White
4 Right Turn Sig- nal Green
5 Right Rear Posi- tion, Side
Marker Lights,
and Rear Regis-
tration Plate
Illumination
Device
1
Brown
6 Stop Lights Red
7 Left Rear Posi- tion, Side
Marker Lights,
and Rear Regis-
tration Plate
Illumination
Device
1
Black
1The rear position registration
plate illumination device shall be
connected such that no light of the
device has a common connection
with both pins 5 and 7.
Thirteen - Pin Connector Details Pin Function Wire
Color
1 Left Turn Signal Yellow
2 Rear Fog Light Blue
3 Ground/
Common Re-
turn for Con-
tacts (Pins) 1
and 2 and 4 to
8
2
White
4 Right Turn Sig- nal Green
5 Right Rear Posi- tion, Side
Marker Lights,
and Rear Regis-
tration Plate
Illumination
Device.
b
Brown
Seven - Pin Connector
Thirteen - Pin Connector
264

WARNING!A transient high voltage occurs at the
bulb sockets of High Intensity Dis-
charge (HID) headlamps when the
headlamp switch is turned ON. It may
cause serious electrical shock or elec-
trocution if not serviced properly. See
your authorized dealer for service.NOTE:On vehicles equipped with High In-
tensity Discharge (HID) headlamps,
when the headlamps are turned on,
there is a blue hue to the lamps. This
diminishes and becomes more
white after approximately 10 sec-
onds, as the system charges.QUAD HEADLAMPS (for
versions/markets, where
provided)CAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and com-
plying with the law.1. Raise the hood to access the high or
low beam bulbs at the rear of the
headlamp housing.
2. Release the two tabs on the side of
the connector and remove the connec-
tor from the bulb.
3. Twist the headlamp bulb and pull
the bulb from the headlamp housing.
4. Install the new headlamp bulb and
twist until locked into the headlamp
housing.
CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life. If the bulb
comes in contact with an oily sur-
face, clean the bulb with rubbing
alcohol.
5. Reconnect the wiring connector to
the bulb.
FRONT TURN SIGNAL AND
SIDE MARKER LAMPS
Access to change the turn signal or
side marker bulb is from the rear of
the headlamp housing. 1. Twist the turn signal or side
marker socket to remove the socket.
2. Pull bulb from the socket.
3. Replace the bulb and reinstall
socket.
SIDE REPEATER LAMPS
The side repeater lamps are located in
both front fenders.
1. Push the side repeater lamp to the
right and release retaining tab on the
left.
2. Pull side repeater lamp out and
disengage bulb socket from lamp.
3. Press, then rotate and pull bulb
from socket.
4. Install bulb to socket.
5. Push the lamp socket into the side
repeater lamp.
Side Repeater Bulb Replacement
309

Trailer Towing . . . . . . . . . . . . 259Cooling System Tips . . . . . . 266
Hitches . . . . . . . . . . . . . . . 266
Minimum Requirements . . . 262
Trailer and Tongue
Weight . . . . . . . . . . . . . . . 261
Wiring . . . . . . . . . . . . . . . . 264
Trailer Towing Guide . . . . . . . 261
Trailer Weight . . . . . . . . . . . . 261
Transaxle Selection of
Lubricant . . . . . . . . . . 299,313
Transmission . . . . . . . . . . . . . 299 Automatic . . . . . . . . . . 230,299
Fluid . . . . . . . . . . . . . . . . . 299
Transmitter Battery Service
(Remote Keyless Entry) . . . . . . 21
Transmitter, Remote Keyless
Entry (RKE) . . . . . . . . . . . . . . 18
Transporting Pets . . . . . . . . . . 62
Tread Wear Indicators . . . . . . 248
Trip Computer . . . . . . . . . . . . 170
Trip Odometer . . . . . . . . . . . . 164 Turbo Cool Down . . . . . . . . . 229
Turn Signals . . . 123,164,309,310
UCI Connector . . . . . . . . . . . 187
Uconnect™ (Hands-Free
Phone) . . . . . . . . . . . . . . . . . . 82
Umbrella Holder . . . . . . . . . . 146
Universal Consumer Interface
(UCI) Connector . . . . . . . . . . 187
Upholstery Care . . . . . . . . . . . 302
Vanity Mirrors . . . . . . . . . . . . . 77
Variance, Compass . . . . . 170,181
Vehicle Identification Number
(VIN) . . . . . . . . . . . . . . . . . . . . 7
Vehicle Modifications/
Alterations . . . . . . . . . . . . . . . . 7
Vehicle Storage . . . . . . . . 220,307
Voice Recognition System
(VR) . . . . . . . . . . . . . . . . . . . 99
Wait to Start Light . . . . . . . . . 176
Warning Flasher, Hazard . . . . 268Warning Lights (Instrument
Cluster Description) . . . . . . . . 164
Warnings and Cautions . . . . . . . 7
Washer
Adding Fluid . . . . . . . . . . . 294
Washers, Headlight . . . . . . . . 126
Washing Vehicle . . . . . . . . . . 301
Water
Driving Through . . . . . . . . 236
Wheel and Wheel Trim . . . . . . 302
Wheel and Wheel Trim Care . . 302
Wind Buffeting . . . . . . . . . 28,140
Window Fogging . . . . . . . . . . 220
Windows . . . . . . . . . . . . . . . . . 26 Power . . . . . . . . . . . . . . . . . 26
Rear Vent . . . . . . . . . . . . . . 26
Windshield Defroster . . . . . . . . 64
Windshield Washers . . . . . . . . 294
Windshield Wiper Blades . . . . 294
Wiper Blade Replacement . . . . 294
Zone Control (Temperature
Control) . . . . . . . . . . . . . . . . 209
334