2011 INFINITI QX56 reset

MWI
MWI-3
C
DE
F
G H
I
J
K L
M B
A
O P
THE LOW WASHER FLUID WARNING CON-
TINUES DISPLAYING, or DOES NOT DIS-
PLAY .............................................................. ....
81
Description .......................................................... ....81
Diagnosis Procedure ...............................................81
THE DOOR OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY ..........
82
Description .......................................................... ....82
Diagnosis Procedure ...............................................82
THE AMBIENT TEMPERATURE DISPLAY IS
INCORRECT .......................................................
83
Description .......................................................... ....83
Diagnosis Procedure ...............................................83
NORMAL OPERATING CONDITION .................84
INFORMATION DISPLAY ..................................... ....84
INFORMATION DISPLAY : Description ..................84
REMOVAL AND INSTALLATION ...............85
COMBINATION METER ...................................85
Exploded View ..................................................... ....85
Removal and Installation .........................................85
Disassembly and Assembly .....................................85
TRIP RESET AND ILLUMINATION CON-
TROL SWITCH ..................................................
86
Exploded View .........................................................86
Removal and Installation .........................................86
TRIP COMPUTER SWITCH ..............................87
Exploded View .........................................................87
Removal and Installation .........................................87
CLOCK ..............................................................88
Exploded View .........................................................88
Removal and Installation .........................................88
Revision: 2010 May2011 QX56

MWI-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
METER SYSTEM
METER SYSTEM : Component Parts LocationINFOID:0000000006221690
1.IPDM E/R
Refer to
PCS-4, "Component Parts
Location". 2.
ECM
Refer to
EC-16, "
Component Parts
Location". 3. Washer level switch
4. Oil pressure switch
Refer to
EM-57, "
Exploded View".5. Ambient sensor 6. A/C auto amp.
Refer to
HAC-6, "
FRONT AUTO-
MATIC AIR CONDITIONING SYS-
TEM : Component Parts Location".
7. TCM
Refer to
TM-10, "
A/T CONTROL
SYSTEM : Componen t Parts Loca-
tion". 8.ABS actuator and electric unit (con-
trol unit)
Refer to
BRC-10, "
Component Parts
Location". 9.BCM
Refer to
BCS-4, "
BODY CONTROL
SYSTEM : Component Parts Loca-
tion".
10. Fuel level sensor unit 11. Trip computer switch 12. Combination meter
13. Trip reset and illumination control
switch 14. Parking brake switch
A. Under of left side second seat
JSNIA3157ZZ
Revision: 2010 May2011 QX56

MWI
COMPONENT PARTSMWI-7
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
METER SYSTEM : Com ponent DescriptionINFOID:0000000006221691
CLOCK
Unit Description
Combination meter Controls the following with the signals received from each unit via CAN communication and the sig-
nals from switches and sensors.
 Speedometer
 Tachometer
 Engine coolant temperature gauge
 Fuel gauge
 Engine oil pressure gauge
 Voltmeter
 Warning lamps
 Indicator lamps
 Meter illumination control
 Meter effect function
 Information display
Trip computer switch Transmits the following signals to the combination meter.
 Enter switch signal
 Select switch signal
Trip reset and illumination con-
trol switch Transmits the following signals to the combination meter.
 Trip reset switch signal
 Illumination control switch signal (+)
 Illumination control switch signal (
−)
ECM Transmits the following signals to the combination meter via CAN communication.
 Engine speed signal
 Engine coolant temperature signal
 Engine status signal
 Fuel consumption monitor signal
ABS actuator and electric unit
(control unit) Transmits the vehicle speed signal to the combination meter via CAN communication.
IPDM E/R Transmits the oil pressure switch signal to the BCM via CAN communication.
BCM Transmits the following signals to the combination meter via CAN communication.
 Oil pressure switch signal
 Position light request signal
 Dimmer signal
 Door switch signal
 Meter ring illumination request signal
 Starter relay status signal
TCM Transmits the shift position signal to the combination meter via CAN communication.
A/T shift selector Transmits the following signals to the combination meter.
 Manual mode signal
 Non-manual mode signal
 Manual mode shift up signal
 Manual mode shift down signal
Fuel level sensor unit Transmits the fuel level sensor signal to the combination meter.
Oil pressure switch Transmits the oil pressure switch signal to the IPDM E/R.
Ambient sensor Transmits the ambient sensor signal to the combination meter.
A/C auto amp. Transmits the A/C auto amp. connection recognition signal to the combination meter.
Parking brake switch Transmits the parking brake switch signal to the combination meter.
Washer level switch Transmits the washer level switch signal to the combination meter.
Revision: 2010 May2011 QX56

MWI-12
< SYSTEM DESCRIPTION >
SYSTEM
METER SYSTEM : Fail-Safe
INFOID:0000000006221695
FA I L - S A F E
The combination meter activates the fail-safe contro l if CAN communication with each unit is malfunctioning.
A. With ASCD models B. With ICC models C. For U.S.A.
D. For Canada
JSNIA3234ZZ
Function Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Engine oil pressure gauge
Illumination control When suspending communication, changes to nighttime mode.
Information display Odo/trip meter An indicated value is maintained at communications blackout.
Shift position indicator The display turns OFF by suspending communication.
Door open warning The display turns OFF by suspending communication.
Buzzer The buzzer turns OFF by suspending communication.
Revision: 2010 May2011 QX56

MWI
SYSTEMMWI-21
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O PNOTE:
 Current fuel consumption on the information di splay is updated approximately every 0.5 seconds.
 Current fuel consumption on the information displa y shows 0 l/100km (0 mpg) when vehicle speed is 0 km/h
(0 MPH).
Average Fuel Consumption
The combination meter calculates average fuel c onsumption based on the following signals, and the calcu-
lated value is displayed on the information display.
NOTE:
 Average fuel consumption on the information display is updated approximately every 30 seconds.
 Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “ −−−”
is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).
Distance to Empty
The combination meter calculates distance to empty based on the following signals, and the calculated value
is displayed on the information display.
NOTE:
 Distance to empty on the information display is updated approximately every 30 seconds.
 When the ignition switch is turned from OFF to ON, “ −−−” is displayed until after a travel of approximately
500 m (0.31 mile).
 The indicated values may not match each other when refueling with the ignition switch ON.
Average Vehicle Speed
The combination meter calculates average vehicle speed based on the following signals, and the calculated
value is displayed on the information display.
NOTE:
 Average vehicle speed on the information disp lay is updated approximately every 30 seconds.
 Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “ −−−”
is displayed until after a 30 seconds.
Travel Time
Signal name Signal path
Fuel consumption monitor signal ECM Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Signal name Signal path
Fuel consumption monitor signal ECM Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Signal name Signal path
Fuel level sensor signal Fuel level sensor unit Combination meter
Fuel consumption monitor signal ECM Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Signal name Signal path
Ignition signal —
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Revision: 2010 May2011 QX56

MWI-26
< SYSTEM DESCRIPTION >
SYSTEM
 The combination meter judges showing/hiding of “other warning”, according to the signals below:
Meter Illumination Level Indication
When receiving the following signals, the combination meter causes an interrupt on the information display to
indicate an illumination level.
WARNING CHECK INDICATION
 The combination meter can cause an interrupt on the information display to indicate a warning, based onsignals received from each unit and switch.
 The indicated warning can be checked with “WARNING” during the satisfaction of an interrupt indication
condition for each warning.
SETTING
Warning indication timing and time can be set.
Alert
Setting values for travel time, and low ambient te mperature can be adjusted to meet the user's needs.
Maintenance
Setting values for engine oil, oil filter, tire, and other maintenance items can be adjusted to meet the user's
needs.
Options
Setting values for unit and effect items can be adjusted to meet the user's needs.
Operating condition
Ignition switch ON
Mileage More than value set in “SETTING”
Signal name Signal path
Ignition signal —
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Signal name Signal path
Ignition signal —
Illumination control switch signal (+) Trip reset and illumination control switch Combination meter
Illumination control switch signal ( −)
Setting item Setting range Setting unit
Alert Timer No setting, 0.5 h - 6 h 0.5 h
ICY ON/OFF —
Setting item Setting range
Maintenance Tire
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Filter No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Oil No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Other No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Revision: 2010 May2011 QX56

MWI-28
< SYSTEM DESCRIPTION >
OPERATION
OPERATION
Switch Name and FunctionINFOID:0000000006221718
JSNIA2978ZZ
Switch name Operation Description
Trip reset and illumi-
nation control switch Trip reset switch (1)
Press The trip meter can be switched between A and B.
 Trip meter A/B can be reset by pressing and holding the
trip reset switch.
Illumination control switch (+) (2) An illuminance level of the back light of the combination
meter can be adjusted.
Illumination control switch ( −) (3)
Trip computer
switch Enter switch (4)  The information display screen can be switched.
 The item indicated on the information display can be con-
firmed.
 An indicated value of the trip computer can be reset by
pressing and holding the enter switch.
Select switch (5) When plural items are shown on the information display, a
selected item can be changed to the other item.
Revision: 2010 May2011 QX56

MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-29
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis FunctionINFOID:0000000006221719
ON BOARD DIAGNOSIS ITEM
The combination meter allows the following diagnosis items with the on-board diagnosis function.
METHOD OF STARTING
1. Turn ignition switch OFF.
2. While pressing the trip reset switch (1), turn ignition switch ON.
3. If the diagnosis function is activated with “trip A” displayed, the
mileage on “trip A” is reset to “0000.0”. (The same way for “trip
B”.)
4. Make sure that the trip meter displays “0000.0”.
5. Press the trip reset switch at least 3 times. (Wit hin 7 seconds after the ignition switch is turned ON.)
6. The combination meter is turned to self-diagnosis mode.  Speedometer, tachometer, engine coolant temper ature gauge, fuel gauge, engine oil pressure gauge,
and voltmeter return to zero, simultaneously.
 The dot matrix dots on the information display (1) blink alter-
nately.
NOTE:
 Check combination meter power supply and ground circuit when the self-diagnosis mode of the combi- nation meter does not start. Replace combination meter if power supply and ground circuit are normal.
 If any of the dots are not displayed, replace combination meter.
Diagnosis item
Drive circuit check  Speedometer
 Tachometer
 Engine coolant temperature gauge
 Fuel gauge
 Engine oil pressure gauge
 Voltmeter
LCD (liquid crystal display) check Information display
JSNIA2978ZZ
JSNIA0020GB
Revision: 2010 May2011 QX56