2011 INFINITI QX56 ground

FRONT FOG LAMP CIRCUITEXL-95
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES >> Replace front fog lamp.
NO >> Repair or replace harness.
(+) (− ) Test item Voltag e
(Approx.)
IPDM E/R
Connector Terminal
RH E1219
GroundEXTERNAL
LAMPS Fog Battery voltage
Off 0 V
LH 20 Fog Battery voltage
Off 0 V
IPDM E/R Front fog lamp
Continuity
Connector Terminal Connector Terminal
RH E1219 E48
1 Existed
LH 20 E30
Front fog lamp
GroundContinuity
Connector Terminal
RH E48 2Existed
LH E30
Revision: 2010 May2011 QX56

EXL-96
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function CheckINFOID:0000000006213964
1.CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the parking lamp is turned ON.
Is the inspection result normal?
YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-96, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213965
1.CHECK PARKING LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK PARKING LAMP SHORT CIRCUIT
1. Disconnect the following connectors.
- IPDM E/R
- Front combination lamp
- Rear combination lamp
- License plate lamp
2. Check continuity between IP DM E/R harness connector and ground.
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect front combination lamp connector.
2. Turn ignition switch ON. TAIL : Parking lamp ON
Off : Parking lamp OFF
Unit Location Fuse No. Capacity
Parking lamp IPDM E/R #46
10 A
#47
IPDM E/R
GroundContinuity
Connector Terminal
RH E1437
Not existed
LH 43
Revision: 2010 May2011 QX56

PARKING LAMP CIRCUITEXL-97
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check vo ltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connec tor and front combination lamp harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between front combination lamp harness connector and ground.
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
(+)
(− ) Test item Voltag e
(Approx.)
IPDM E/R
Connector Terminal
RH E1437
GroundEXTERNAL
LAMPS TAIL Battery voltage
Off 0 V
LH 43 TAIL Battery voltage
Off 0 V
IPDM E/R Front combination lamp
Continuity
Connector Terminal Connector Terminal
RH E1437 E119
7 Existed
LH 43 E118
Front combination lamp
GroundContinuity
Connector Terminal
RH E119 3Existed
LH E118
Revision: 2010 May2011 QX56

TURN SIGNAL LAMP CIRCUITEXL-99
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
TURN SIGNAL LAMP CIRCUIT
Component Function CheckINFOID:0000000006213967
1.CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamp is turned ON.
Is the inspection result normal?
YES >> Turn signal lamp circuit is normal.
NO >> Refer to EXL-99, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213968
1.CHECK TURN SIGNAL LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK TURN SIGNAL LA MP OUTPUT VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector, door mirror connector and rear combination lamp connec- tor.
3. Turn ignition switch ON.
4. With operating the turn signal switch, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4. LH : Turn signal lamps (LH) ON
RH : Turn signal lamps (RH) ON
Off : Turn signal lamps OFF
(+)
(–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M70 60
GroundTurn signal
switch LH
OFF 0 V
61 RH
OFF 0 V
PKID0926E
PKID0926E
Revision: 2010 May2011 QX56

EXL-100
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front combination lamp, door mirror or rear combi- nation lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Check each bulb socket for internal short circuit. Replace BCM if check result is normal. Refer to BCS-81, "
Removal and Installation".
NO >> Repair or replace harness.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between front combination lamp, door mirror or rear combination lamp and ground.
Front turn signal lamp
Side turn signal lamp
BCM Front combination lamp Continuity
Connector Terminal Connector Terminal
LH M7060 E118
8 Existed
RH 61 E119
BCM Door mirror Continuity
Connector Terminal Connector Terminal
Driver side M7060 D3
20 Existed
Passenger side 61 D23
BCM Rear combination lamp Continuity
Connector Terminal Connector Terminal
LH M7060 B60
3 Existed
RH 61 B232
BCM
GroundContinuity
Connector Terminal
M70 60
Not existed
61
Front combination lamp
GroundContinuity
Connector Terminal
LH E118 3 Existed
RH E119
Door mirror GroundContinuity
Connector Terminal
Driver side D3 19 Existed
Passenger side D23
Revision: 2010 May2011 QX56

TURN SIGNAL LAMP CIRCUITEXL-101
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
Rear turn signal lamp
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Rear combination lamp GroundContinuity
Connector Terminal
LH B60 4 Existed
RH B232
Revision: 2010 May2011 QX56

EXL-102
< DTC/CIRCUIT DIAGNOSIS >[XENON TYPE]
OPTICAL SENSOR
OPTICAL SENSOR
Component Function CheckINFOID:0000000006213969
1.CHECK OPTICAL SENSOR SI
GNAL BY CONSULT-III
CONSULT-III DATA MONITOR
1. Turn ignition switch ON.
2. Select “OPTISEN (DTCT)” of BCM (HEADLAMP) data monitor item.
3. Turn lighting switch AUTO.
4. With the optical sensor illuminating, check the monitor status.
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?
YES >> Optical sensor is normal.
NO >> Refer to EXL-102, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006213970
1.CHECK OPTICAL SENSOR POWER SUPPLY INPUT
1. Turn ignition switch ON.
2. Turn lighting switch AUTO.
3. Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK OPTICAL SENSOR GROUND INPUT
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 6.
3.CHECK OPTICAL SENSOR SIGNAL OUTPUT
With illuminating the optical sensor, check vo ltage between optical sensor harness connector and ground.
Monitor item Condition Voltage (Approx.)
OPTISEN (DTCT) Optical sensor When illuminating 3.1 V or more *
When shutting off light 0.6 V or less
(+)
(− ) Vo l ta g e
(Approx.)
Optical sensor
Connector Terminal M17 1 Ground 5 V
(+) (− ) Vo l ta g e
(Approx.)
Optical sensor
Connector Terminal M17 3 Ground 0 V
Revision: 2010 May2011 QX56

OPTICAL SENSOREXL-103
< DTC/CIRCUIT DIAGNOSIS > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace the optical sensor.
4.CHECK OPTICAL SENSOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK OPTICAL SENSOR SHORT CIRCUIT
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-81, "Removal and Installation".
NO >> Repair or replace harness.
6.CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-81, "Removal and Installation".
NO >> Repair or replace harness.
7.CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
(+)
(− ) Condition Vo l ta g e
(Approx.)
Optical sensor
Connector Terminal
M17 2 Ground Optical sensor When illuminating 3.1 V or more *
When shutting off light 0.6 V or less
Optical sensor BCM
Continuity
Connector Terminal Connector Terminal
M17 1 M68 17 Existed
Optical sensor GroundContinuity
Connector Terminal
M17 1 Not existed
Optical sensor BCM Continuity
Connector Terminal Connector Terminal
M17 3 M68 18 Existed
Revision: 2010 May2011 QX56