2010 MITSUBISHI OUTLANDER Owners Manual

7-68 Vehicle care and maintenance
7
2. Turn the socket and bulb assembly counterclockwise to
remove it.NOTE

The tail and stop light uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.3. Pull the bulb out of the socket.
B- Tail and stop light (LED) - cannot be replaced
C- Rear turn-signal light
BK0115300US.book 68 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-69
7
4. To install the bulb, perform the removal steps in reverse.NOTE

When mounting the light unit, align the clips (D) on the
light unit with the hole in the body.
Back-up lights
N00929100041
1. Open the tailgate.
2. Insert a screwdriver into the notch of the cover and pry
gently to remove the cover.NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the cover.
BK0115300US.book 69 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-70 Vehicle care and maintenance
7
3. Turn the socket (A) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
BK0115300US.book 70 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-71
7
Rear side-marker lights
N00935400094
1. Open the lower gate and pull back the cover between the
passenger compartment and the lower gate.
2. Remove the cover after you remove each of the 4 clips (A)
by inserting a screw driver into the clip groove and lever-
ing it toward the vehicle body.3. Remove the light mounting screw (B) and remove the
light unit.
BK0115300US.book 71 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-72 Vehicle care and maintenance
7
4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
NOTE

When mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
BK0115300US.book 72 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-73
7
License plate lights
N00944000360
1. When removing the light unit (A), push it toward the left
side of the vehicle body.2. Use a screw driver to gently pry up the tab (B) and remove
the lens.
NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0115300US.book 73 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-74 Vehicle care and maintenance
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTE

When mounting the light unit, insert tab (C) first then
align tab (D) with its hole.
BK0115300US.book 74 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-75
7
High-mounted stop light
N00943900102
NOTE

The high-mounted stop light uses an LED instead of the
bulb. Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when the light needs to
be repaired or replaced.
Dome light (front)/Reading lights
N00944500251
1. Insert a screwdriver into the notch of the light assembly.
Gently pry to remove the lens.NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0115300US.book 75 ページ ２００９年７月１６日　木曜日　午前９時１３分