2010 JAGUAR XFR Torque bolt

10.
















11.
12.
13. NOTE: Tighten in the sequence indicated.

Torque:
Bolt 2 30 Nm Bolt 3 30 Nm Bolt 1 30 Nm Bolt 4 30 Nm











NOTE: RH shown LH similar.

Special Tool(s): 303-1450 Torque: 20 Nm




















Torque: 7 Nm

14.
15. NOTES:


Lubricate
the union
threads with
clean engine
oil.


Do not
tighten at
this stage.


Remove and
discard the
blanking
caps.





Torque:
union 21 Nm bolts 8 Nm














16.
Torque: 21 Nm











17.
Refer to: Air Cleaner Outlet Pipe RH (303-12C Intake Air Distribution and Filtering - V8 5.0L Petrol, Removal and Installation).

5. CAUTION: If a new cylinder head has been installed then the special tool
310-200-02 without the thread must be used to install the fuel rail.

Special Tool(s): 310-200-01, 310-200-02












6. CAUTIONS:


Make sure that the area around the open fuel injector ports are clean
and free of foreign material and lubricant prior to installing the fuel injector.


When Installing the fuel injector(s), make sure that the Teflon seal is
clean and free of foreign material and lubricant.









7. CAUTIONS:


If new fuel injectors are installed, a new injector clamp must be
installed


Make sure that the fuel injector is aligned and installed into the fuel
rail correctly, as noted in the removal step.


Tighten the fuel rail retaining bolts a turn at a time until the correct
torque is achieved.


NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.

Torque: 20 Nm







8. NOTE: LH shown RH similar.
Special Tool(s): 310-200-01, 310-200-02

9.
















10.
11.
12. NOTE: LH shown RH similar.

Torque: 20 Nm













NOTES:


LH shown RH similar.


Tighten in the sequence indicated.

Torque:
Bolt 2 30 Nm Bolt 3 30 Nm Bolt 1 30 Nm Bolt 4 30 Nm























Special Tool(s): 303-1450 Torque: 20 Nm

13.
















14.
15. NOTE: LH shown RH similar.

Torque: 7 Nm















NOTE: LH shown RH similar.

















CAUTION: Lubricate only the union threads with clean engine oil.

NOTES:


Engine shown removed for clarity.


Install the bolt and unions finger tight before final tightening.


Remove and discard the blanking caps.
















16. Lower the vehicle. www.JagDocs.com

24.


















25.


















NOTES:


Lubricate the
union threads
with clean
engine oil.


Do not
tighten at
this stage.


Remove
and discard
the blanking
caps.





26. Torque:
Unions 21 Nm Bolts 8 Nm

5. CAUTION: Install new high-pressure fuel supply lines.
NOTES:
Engine shown removed for clarity.

Remove and discard the blanking caps.

Install the bolt and unions fully finger tight before final
tightening.























6. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.

NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.
Torque: 12 Nm





7. Lower the vehicle.
8. NOTES:

Do not tighten at this stage.

Remove and discard the blanking caps.








9. WARNING: Do not work on or under a vehicle supported only by a jack. Always

12.
13.
14. NOTES:

Install the bolt and unions finger tight before final tightening.

Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm














Torque: 21 Nm


















NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm