2010 JAGUAR XFR Torque bolt

26. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.

first. NOTE: Make sure to tighten the inlet VVT unit bolts
Torque: 32 Nm












27.
28.
Remove the special tool.

























Remove the special tool.

29.
30.
31.
Remove the special tool.
Special Tool(s): 303-1447















Install the special tool.
Special Tool(s): 303-1448
















CAUTION: Install the crankshaft pulley bolt with an
M16 washer to prevent damage to the crankshaft on
installation.
Torque: 50 Nm

3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 13 Nm

3. NOTE: Tighten the bolts in the indicated sequence.

Torque: 13 Nm

3. NOTE: Tighten the bolts in the indicated sequence.

Torque:
M6 12 Nm M8 20 Nm











4. Torque: 12 Nm













5. Refer to: Brake Vacuum Pump - V8 5.0L Petrol/V8 S/C 5.0L Petrol (206-07 Power Brake Actuation, Removal and Installation).

6. Torque: 25 Nm

7. NOTE: Install the bolt finger tight before final
tightening.
Torque: 40 Nm












8. Torque: 40 Nm













9. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

10. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


11. CAUTION: Make sure that the vehicle is left for 5 minutes from
filling with oil and that the engine oil level is reading at least minimum
(by following Steps 14-18), before starting the engine.

Fill the engine with oil - for filling values on vehicles without
supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications).
Fill the engine with oil - for filling values on vehicles with
supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications).
Clean any residual engine oil from the oil filler cap area.


12. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.
Follow the Steps 14-18 before starting the engine.

13.
Start the engine and allow to run for 10 minutes, stop the
engine.

Engine - V8 S/C 5.0L Petrol - Engine
Installation

NOTES:


Some variation in the illustrations may occur, but the essential information is always correct. Published: 19-Nov-2013

If a new engine is to be installed, remove the intake manifold to access the top transmission retaining bolts.


1. NOTE: This step requires the aid of another technician.
Install the engine assembly.





















2. Torque: 45 Nm

6. CAUTIONS:


Make sure that the area around the open fuel injector ports are clean
and free of foreign material and lubricant prior to installing the fuel injector.


When Installing the fuel injector(s), make sure that the Teflon seal is
clean and free of foreign material and lubricant.










7. CAUTIONS:


If new fuel injectors are installed, a new injector clamp must be
installed


Make sure that the fuel injector is aligned and installed into the fuel
rail correctly, as noted in the removal step.


Tighten the fuel rail retaining bolts a turn at a time until the correct
torque is achieved.


NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.

Torque: 20 Nm







8. Special Tool(s): 310-200-01, 310-200-02 9. Torque: 20 Nm