2010 JAGUAR XFR Torque bolt

Installation


1. CAUTION: Make sure that the battery negative cable
to the body retaining bolt is not loose and fully tightened.
Torque: 9 Nm















2. NOTE: Make sure that both the positive and negative battery
terminals are correctly located.

To install, reverse the removal procedure.





















3. NOTE: This step is only necessary when installing a new
component.

Using the Jaguar approved diagnostic equipment, reset the battery
monitoring system.

4. Refer to: Door Window Motor Initialization (501-11 Glass, Frames and Mechanisms, General Procedures).

5. Enter the audio unit preset radio frequencies.

6. Reset the clock to the correct time.

7. Start the engine and allow to idle until the engine reaches normal
operating temperature.
8. Switch the engine off. www.JagDocs.com

2. CAUTIONS:


Install all the bolts finger tight before final tightening.


Care must be taken not to damage the outer door
panel.

Install the retaining bolt 1 to the witness mark on
the body.
Torque:
1 1.9 Nm 2 5 Nm






















3. NOTE: Components removed for clarity.
4. NOTE: Right-hand shown, left-hand similar.
Torque: 1.5 Nm









5. Refer to: Front Door Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

Instrument Panel and Console - Glove Compartment
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Passenger Side Register (412-01 Climate Control, Removal and Installation).

2.
3. CAUTION: Fixings must be started by hand to avoid
damaging threads.

Upper 3 bolts.

Torque: 2.5 Nm Lower 3 bolts.

Torque: 9 Nm

Lower 3 bolts.

Torque: 9 Nm www.JagDocs.com

Wipers and Washers - Windshield Wiper Motor
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Cowl Vent Screen (501-02 Front End Body Panels, Removal and Installation).


3. CAUTION: Tighten the bolts in the sequence shown.


NOTE: LHD illustration shown, RHD is similar.

Torque: 12 Nm










4. NOTE: LHD illustration shown, RHD is similar.
5. NOTE: LHD illustration shown, RHD is similar.

Bumpers - Front Bumper Cover
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011


1. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Torque: 3 Nm 3. Torque:
Retaining screws 2 Nm Retaining bolts 7 Nm

Safety Belt System - Front Safety Belt Buckle
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Refer to: Front Seat (501-10 Seating, Removal and Installation).



Installation
3. CAUTION: Discard the bolt.
Torque: 35 Nm

1. CAUTION: Make sure that a new bolt is installed. To
install, reverse the removal procedure.

1. CAUTION: Only tighten the bolts finger-tight at this stage.














2. CAUTION: Tighten the bolts in the sequence shown.
Torque:
Bolt 1 63 Nm Bolt 2 63 Nm Bolt 1 63 Nm


















3. Torque: 12 Nm www.JagDocs.com