2010 JAGUAR XFR lock

14. NOTES:


Make sure the tie-rod or tie-rod end does not rotate.


Left-hand shown, right-hand similar.

Tighten the tie-rod end lock nut
Tighten to 55 Nm.







15. NOTE: Make sure that all fixings are torqued to the correct
specification.

Check the caster and toe settings. Follow the equipment manufacturer's
instructions. Adjust as necessary.

Published: 16-Oct-2013
Suspension System - General Information - Four-Wheel Alignment
General Procedures
CAUTIONS:

Make sure the vehicle is on a flat level surface.
Make sure the tire pressures are within specification.
Make sure that only the manufacturers' recommended four wheel alignment equipment is used.
Make sure the steering is in the straight ahead position.
1. For wheel alignment information, refer to the suspension specification
section.
For additional information, refer to: Specifications (204-00 Suspension System - General Information, Specifications).

2. Check the tie rod ends, suspension joints, wheel bearings and wheels
and tires for damage, wear and free play.
Adjust or repair any worn, damaged or incorrectly adjusted
components.

3. Check and adjust tire pressures.

4. Position the vehicle on a calibrated, level, vehicle lift.

5. Vehicles with air suspension.
For additional information, refer to: Air Suspension Manual Tight
Tolerance Setting Mode (204-05, General Procedures).

6. Release the vehicle parking brake.

7. Using only four-wheel alignment equipment approved by Jaguar, check
the wheel alignment.


8. NOTE: LH illustration shown, RH is similar. To
adjust, loosen the toe link locknuts. www.JagDocs.com

9. CAUTION: Do not allow the gaiter to twist.
NOTES:

Both tie rods must be rotated by an equal amount.


LH illustration shown, RH is similar.

Adjust the rear toe.




10. Tighten the toe link locknuts to 55 Nm (40 lb.ft).


11.
















12. NOTE: LH illustration shown, RH is similar.

To adjust the caster, loosen the front lower arm lock nuts.














NOTE: LH illustration shown, RH is similar.

Rotate the caster adjustment cam bolt.











13. CAUTION: Make sure the caster adjustment bolt does not rotate
while the lock nut is being tightened.
Tighten the caster adjustment cam bolt nut.
Tighten the nut and bolt to 175 Nm (129 lb.ft).

14.
















15. CAUTION: Adjustments made to the camber setting will
affect the front toe setting. Therefore , the camber and toe
may need to be adjusted at the same time.


NOTE: LH illustration shown, RH is similar.
To adjust the camber, loosen the rear lower arm lock nuts.









NOTE: LH illustration shown, RH is similar.

Rotate the camber adjustment cam bolt.











16. CAUTION: Make sure the camber adjustment bolt does not rotate
while the lock nut is being tightened.
Tighten the camber adjustment cam bolt nut.
Tighten the nut and bolt to 175 Nm (129 lb.ft).


17. NOTE: LH illustration shown, RH is similar.
To adjust, loosen the tie rod end lock nuts.

18. CAUTION: Do not allow the gaiter to twist.

NOTES:


Both tie rods must be rotated by an equal amount.


LH illustration shown, RH is similar.

Adjust the front toe.




19. Tighten the tie rod end lock nuts to 55 Nm (40 lb.ft).

20. Using only four-wheel alignment equipment approved by Jaguar, check
the wheel alignment.

Published: 16-Oct-2013
Suspension System - General Information - Front Toe Adjustment
General Procedures
CAUTIONS:

Make sure the vehicle is on a flat level surface.
Make sure the tire pressures are within specification.
Make sure that only the manufacturers' recommended four wheel alignment equipment is used.
Make sure the steering is in the straight ahead position.
1. For wheel alignment information, refer to the suspension specification
section.
For additional information, refer to: Specifications (204-00 Suspension System - General Information, Specifications).

2. Check the tie rod ends, suspension joints, wheel bearings and wheels
and tires for damage, wear and free play.
Adjust or repair any worn, damaged or incorrectly adjusted
components.

3. Check and adjust tire pressures.

4. Position the vehicle on a 4 post lift.

5. Release the vehicle parking brake.

6. Vehicles with air suspension.
For additional information, refer to: Air Suspension Manual Tight
Tolerance Setting Mode (204-05, General Procedures).

7. For additional information, refer to: Air Suspension Manual Tight
Tolerance Setting Mode (204-05, General Procedures).

8. Using only four-wheel alignment equipment approved by Jaguar, check
the wheel alignment.


9. NOTE: LH illustration shown, RH is similar. To
adjust, loosen the tie rod end lock nuts.

10.
















11. CAUTION: Do not allow the gaiter to twist.

NOTES:


Both tie rods must be rotated by an equal amount.


LH illustration shown, RH is similar.

Adjust the front toe.







NOTE: LH illustration shown, RH is similar.

Tighten the tie rod end lock nuts to 55 Nm.










12. Using only four-wheel alignment equipment approved by Jaguar, check
the wheel alignment. www.JagDocs.com

Published: 16-Oct-2013
Suspension System - General Information - Rear Toe Adjustment
General Procedures

1. Vehicles with air suspension.
For additional information, refer to: Air Suspension Manual Tight
Tolerance Setting Mode (204-05, General Procedures).

2. Check the toe settings. Follow the equipment manufacturer's
instructions.


3. NOTE: Left-hand, shown right-hand similar.

Loosen the lock nut.
Clean and lubricate the lock nut and toe link threads.












4. Rotate the toe link to adjust the toe settings.
5. Tighten the lock nut.













6. Check the toe settings. Follow the equipment manufacturer's
instructions.