2009 SUBARU TRIBECA Reverse

SR-5
Glass Lid
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
3. Glass Lid
A: REMOVAL
1) Completely close the glass lid, and then open
the sunshade.
2) Remove the cover (A), and then remove the
TORX® bolts (B).
CAUTION:
The thread locker is applied to the TORX® b o l t s ,
so use the new parts once they are removed.
3) Remove the glass lid carefully.
B: INSTALLATION
Install in the reverse order of removal.
C: ADJUSTMENT
Loosen the glass lid mounting TORX® bolts (A),
and then adjust the height with moving the lid.
Difference in height between glass lid and roof
panel L:
2.0±1.0 mm (0.079 ± 0.039 in)
(A)
(B)
SR-00091
(A)
SR-00117
L

SR-7
Sunroof Assembly
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
4. Sunroof Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the roof trim. AL, Roof Trim.>
3) Disconnect the harness connector of sunroof
motor.
4) Remove the glass lid. AL, Glass Lid.>
5) Remove the drain tube from frame assembly.
6) Remove the bolts, and then detach the frame as-
sembly.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be careful not to snag the harness.
NOTE:
•Be sure to connect the harness connector.
•When installing the drain tube, insert it securely
into drain pipe.
Length A:
15 mm (0.59 in) or more
C: DISASSEMBLY
1) Remove the sunroof motor. MOVAL, Sunroof Motor.>
2) Remove the sunshade. MOVAL, Sunshade.>
D: ASSEMBLY
Assemble in the reverse order of disassembly.
SR-00005
A

SR-9
Sunroof Motor
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
5) Check the operation of sunroof with following table.
6) Install the trim in the reverse order of removal.
Operation Switch position
(1) Glass lid closes completely.Close
(2) Glass lid tilt up to the top position. Tilt up
(3) Glass lid lowers completely.Tilt down
(4) Glass lid opens completely.Open
(5) Glass lid closes 150 mm (5.91 in) away from the completely closed position. Close
(6) Glass lid closes completely.Close

SR-10
Sunroof Switch
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
6. Sunroof Switch
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light lens (A) and sunroof
switch mounting screws (B).
3) Disconnect the harness connector, and then re-
move the sunroof switch.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the sunroof switch resistance.
Switch position Terminal No. StandardConnector
No.
Open 1 and 3Less than
1 ΩR128
Close 3 and 4Less than
1 Ω
Tilt up 1 and 3Less than
1 ΩR187
Tilt down 3 and 4Less than
1 Ω
LI-00521
LI-00522

SR-11
Sunshade
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
7. Sunshade
A: REMOVAL
1) Remove the glass lid. AL, Glass Lid.>
2) Loosen the TORX® bolt to remove the front sun-
shade bracket.
3) Pull the sunshade until the rear sunshade brack-
et comes into the sight, then loosen the TORX ®
bolts to remove the sunshade.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. CHECK FOR MOVING LOAD OF SUN-
SHADE
1) Attach a spring balance to sunshade edge using
a cloth.
2) Pull the spring balance to measure moving load
of the sunshade.
Moving load of sunshade:
Specification
18.0±5.0 N (1.8±0.5 kgf, 13±3.7 lbf)
NOTE:
Moving load is larger at the beginning of pulling a
spring balance, so take a spring balance reading
while sunshade sliding smoothly.
3) If moving load exceeds specifications, check the
glass lid, sunshade and frame assembly for im-
proper installation.
SR-00122
SR-00123
SR-00087

WW-6
Combination Switch (Wiper)
WIPER AND WASHER SYSTEMS
3. Combination Switch (Wiper)
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the driver’s airbag module. 15, REMOVAL, Driver’s Airbag Module.>
3) Remove the steering wheel. MOVAL, Steering Wheel.>
4) Remove the screws and remove the steering
column covers (upper & lower).
5) Disconnect the connector from the combination
switch.
6) Remove the three screws, and pull out the com-
bination base switch assembly toward you.
7) Remove the screws which secure the switch,
then remove the combination switch.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. COMBINATION SWITCH
1) Inspect the continuity between each connector
terminal.
2) If continuity is not as specified, replace the
switch.
SL-00258
LI -00332
Switch positionTerminal No.Standard
Fr o n t
LO 7 and 17 Less than 1 Ω
HI 8 and 17 Less than 1 Ω
Washer ON 2 and 11 Less than 1 Ω
Rear
Washer ON 2 and 12 Less than 1 Ω
OFF
2 and 10
2 and 12
2 and 13
10 and 12
10 and 13
12 and 13
1 MΩ or more
INT 2 and 13 Less than 1 Ω
ON 2 and 10 Less than 1 Ω
Washer ON
2 and 12
12 and 10
2 and 10
Less than 1 Ω
WW-00046
87654321917 16 15 14 13 12 11 1018

WW-10
Wiper Blade
WIPER AND WASHER SYSTEMS
4. Wiper Blade
A: REMOVAL
CAUTION:
When replacing the wiper blade, if standing up
the wiper arm, be sure to stand up the driver’s
side wiper arm first, and then passenger’s side
wiper arm next. Also, when putting the wiper
arms back, be sure to start with passenger’s
side first, then driver’s side next. Doing this in
the reverse order may result in the driver’s side
wiper blade hitting the passenger’s side wiper
arm and causing damage.
1. FRONT
While pushing the locking clip to the direction of the
arrow, pull out and remove the blade from the arm.
2. REAR
Turn the blade in the direction of arrow (A) and re-
move it from arm.
B: INSTALLATION
1) Install in the reverse order of removal.
2) Confirm that the clip is locked securely.
C: DISASSEMBLY
1. FRONT
Pull side (A) of the wiper rubber stopper and re-
move the rubber from the blade assembly.
2. REAR
Pull the wiper rubber top slightly from stopper (A)
and pull out completely.
WW-00354
(A) Turn the wiper blade.
(1) Wiper arm
(2) Wiper blade
(3) Wiper blade attachment section
(1)
(2)
(3)(A)WW-00207
WW-00009
WW-00143
(A)

WW-13
Washer Tank and Motor
WIPER AND WASHER SYSTEMS
5. Washer Tank and Motor
A: REMOVAL
1) Open the front hood.
2) Disconnect the ground cable from battery.
3) Remove the front bumper. MOVAL, Front Bumper.>
4) Remove the clip holding washer water supply
tap.
5) Remove the two bolts and one nut, hose, con-
nector and washer motor cover, and then remove
the washer tank.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
6.0 N·m (0.61 kgf-m, 4.4 ft-lb)
C: DISASSEMBLY
Pull out the washer motor from the tank.
D: ASSEMBLY
1) Assemble in the reverse order of disassembly.
2) Confirm that water does not leak from installa-
tion area of motor.
E: INSPECTION
Apply battery voltage to the connector terminal of
the washer motor and make sure the motor oper-
ates.
WW-00355
WW-00356
WW-00357
WW-00358
12