2009 SKODA YETI park assist

Starting-off and Driving
116
•
The external sound source of the park
assist and the parking aid can be
disruptively influenced and under unfavourable conditions, objects or people cannot be recognised by the sensors of the parking aid.
Caution
•
If other vehicles are parked behind or on
the kurb, the park assist guides your
ve hicle be yond the kurb or onto it. Make s ure that the whee ls or the whe el rims of yo ur vehicle are not damaged and if necessary intervene in time.•
You should satisfy yourself before parking that there is no small obstacle, such as a
rock, thin post, trailer drawbar etc., in front
or behind your vehicle. Such an obstacle
might not be within the range detected by the sensors.•
Under certain circumstances, surfaces or st
ructures of certain objects such as wire
mesh fences, powder snow etc..., ca
nnot be recognised by the system.
•
The evaluation of the parking space and the parking procedure depends on the
circumference of the wheels. The system does not function correctly if your vehicle is mounted with wheels of non-permissible
size, snow chains or a temporary spare
wheel (in order to reach the nearest workshop). If the tyres other than those excepted by the manufacturer are mounted, the resulting position of the vehicle in the parking space can differ slightly. The parking assistant system automatically performs the correction of the wheel circumference when driving.•
The accuracy of the evaluation for the parking space can be influenced by the
incorrectly determined outside temperature if
the later is influenced by the thermal
radiation of the engine i.e for stop and go in a traffic jam.•
In order to avoid damaging th
e sensors while cleaning wi
th high-pressure cleaners
or steam jets, the sensors must only be
directly sprayed for short periods while a
minimum distance of 10 cm must be observed.
Note
•
A component of the park assist is the front and rear parking aid*.
•
The electronic stability programme (ESP*)
must always be switched on for the
parking procedure.
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing de
vice*). This is why it is not possible to
park backwards with the help of the
park assist when towing a trailer.
•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.Switch on display of the park a
ssist in the information display*
Fig. 119 Switching on the park assist / information display: Finding a suitable parking spaceSwitch on display of the park assist in the information display*– Press the button
⇒fig. 119
.
– Drive past the parking row up to maximum 30 km/h and with a distance of 0.5 m to
1.5 m
⇒fig. 119
.
Operate the turn signal for the driver's side if
you wish to park on this side of the road.
In the information display* the search area
for the parking space is indicated on the
driver's side. If you press the button at a speed greate
r than 30 km/h and less than 50 km/h, the
message indicating that the speed for detecting the space is exceeded will be displayed in the information display of the in
strument cluster. If the speed drops below
30 km/h, the condition of the parking assistant is automatically displayed in the infor-mation display of the instrument cluster. When exceeding the speed of 50 km/h, it is required to activate the displa
y again by pressing the button
⇒fig. 119
.
WARNING (continued)
sgg.6.book Page 116 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
117
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
If the park assist is switched on, a yell
ow warning light lights up in the button.
•
The search for suitable parking spaces is
automatic after switching on the ignition
at speeds of more than 30 km/h. Searching for a parking space is performed at the same time on the driver and front passenger side.•
If the sensors find a suitable parking space, they store its parameters until another
suitable parking space has been found or until
a distance of 10 m had been driven after
finding the parking space. This is why it is
possible to switch on the park assist after
driving past the parking space, the information on whether this parking space is suit- able for parking appears in the information display*.Parking with the help of the park assist and concluding the parking procedureFig. 120 Information display: the determined pa
rking space with the information to drive on
and for engaging the reverse gear
Fig. 121 Information display: Information for
engaging the forward gear or the reverse
gear The time limit for the parking procedure with the help of the park assist lasts 180 seconds. – If the park assist has recognised a suitable parking space, it is shown in the infor-
mation display*
⇒fig. 120
.
– Drive on further until the display
⇒fig. 120
appears.
– Bring the vehicle to a stop for at least 1 second.– Engage the reverse gear or set the selector lever* in the position
R.
– As soon as the following message is shown in the information display*:
Steering
interv. active. Monitor area around veh.!
, let go of the steering wheel, the
steering will be taken over by the system.
– Observe the surroundings and drive backwards with a speed of maximum 7 km/h,
at the same time operate the pedal.
– In the event that the parking procedure cannot be carried out in one go, proceed
to parking in further stages. If the forward arrow flashes in the information display* ⇒ fig. 121
, engage the forward gear.
– Observe the surroundings and drive forw
ards with a speed of maximum 7 km/h.
–If the backward arrow
⇒fig. 121
flashes in the information display*, once again
engage the reverse gear or move the selector lever* into the position
R and care-
fully drive backwards. You can repeat these steps several times.
AA
AB
AC
AD
AA
AB
AC
AD
sgg.6.book Page 117 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
118
– End the parking procedure from a distance on the basis of the information of the
system.
As soon as the parking procedure is comple
ted, an audible signal sounds and in the
information display* the following message appears:
Steering interv. finished.
Please take over steering!
.
Switch off park assist The park assist switches off during
one of the following occurences:
•
a speed of 30 km/h exceeded,
•
a speed of 7 km/h exceeded during the parking procedure,
•
a time limit of 180 seconds exceeded for the parking procedure,
•
the button pressed for the park assist,
•
parking aid activated,
•
intervention of the driver in the automatic steering procedure (stop the steering
wheel),•
Disengage reverse gear or take selector lever* out of the position
R when driving
backwards into the parking space. Further warning and information texts of the park assist in the information display*: Park Assist finished. The parking procedure has ended or after switching on the ignition, the vehicle has not been driven above 10 km/h. Park Assist: Speed too high! Reduce the speed below 30 km/h. Driver steering intervention!
Please take over steering!
The parking procedure is ended through driver intervention. Park Assist finished. ASR switched off The parking procedure cannot be carried ou
t because the TCS system is switched off.
ASR switched off. Please take over steering! The parking procedure was ended because the TCS system was switched off during the parking procedure. Park Assist finished. Trailer The parking procedure is not possible beca
use the trailer is hitched and a plug is
inserted in the socket of the towing device. Time limit exceeded. Please take over steering! The parking procedure was ended because a time limit of 180 seconds for parking was exceeded. System fault: Park Assist finished. The parking procedure is not possible becaus
e a fault exists on the vehicle. Have the
fault rectified by a specialist workshop. Park Assist defective. Workshop! The parking procedure is not possible because
a fault exists on the park assist. Have the
fault rectified by a specialist workshop. Steering interv. active. Mo
nitor area around veh.!
The park assist is active and takes over the steering movements. Observe the surroundings and carefully drive backward
s, at the same time operate the pedal.
Please take over steering!
Finish parking proc. manually
Take over the steering. End the parking procedure without using the park assist. Speed too high! Please take over steering! The parking procedure was ended while the speed was exceeded. Park Assist: ESP intervention! Intervention of the ESP system while searching for a suitable parking place. ESP intervention! Please take over steering! Parking procedure is ended through the intervention of the ESP system. Park Assist: Stationary time not sufficient. The stationary time of the ve
hicle was less than 1 second.
sgg.6.book Page 118 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
119
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Park Assist: Speed too low. After the ignition is switched on, the vehicle must exceed the speed of 10 km/h at least once.Cruise control system (CCS)*IntroductionThe cruise control system (CCS) maintains
a constant speed, more than 30 km/h (20
mph), once it has been set, without you havi
ng to depress the accelerator pedal. This
is only possible within the range which is permitted by the power output and braking power of the engine. The cruise control system
makes it possible - particularly on long
journeys - for you to rest your “accelerator foot”.
WARNING
•
The cruise control system must not, for safety reasons, be used in dense
traffic or on unfavourable road surfaces
(such as icy roads, slippery roads or
loose chippings) - risk of accident!•
In order to prevent unintentional use of the cruise control system, always
switch off the system after use.
Note
•
Models fitted with a manual gearbox: Always
depress the clutch pedal if you switch
on the cruise control system when the gearbox is in Neutral. Otherwise the engine can rev up unintentionally.•
The cruise control system is not able to
maintain a constant speed when driving on
steep downhill sections. The weight of the vehicle increases the speed at which it travels. One should shift down in good time
to a lower gear or slow the vehicle down
by applying the foot brake.•
It is not possible on vehicl
es fitted with an automati
c gearbox to switch on the
cruise control system if the selector lever is in the position
P, N or R.
Storing a speedThe cruise control system is operated by means of the switch and rocker button in the left lever of the multi-functional switch. – Press the switch
⇒fig. 122
into the position
ON
.
– After the desired speed has been reached, press the rocker button into the
SET

position.
After you have released the rocker button out of the position
SET
, the speed you
have just stored is maintained at a consta
nt speed without having to depress the accel-
erator. You can
increase
the speed by depressing the accelerator. Releasing the accelerator
will cause the speed to
drop
again to the set speed.
This does not apply, however, if you drive at a speed which is more than 10 km/h higher than the set speed for a period of longer than 5 minutes. The stored speed will be cancelled in the memory. You then have to re-store the desired speed. One can
reduce
the speed in the usual manner. The system is switched off temporarily
by actuating the brake or clutch pedal
⇒page 120.
WARNING
First ensure that it is not too high for the traffic conditions which exist at that moment before resuming the stored speed.
Fig. 122 Operating lever: Rocker button and switch of cruise control system
AA
AB
AA
AB
AB
sgg.6.book Page 119 Thursday, September 24, 2009 2:32 PM

Automatic gearbox DSG*
121
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Automatic gearbox DSG*Automatic gearbox DSG*IntroductionYour car is equipped with an automatic
gearbox DSG. The abbreviation DSG means
Direct shift gearbox (Direct shift gearbox). Two independent clutches are needed for the power transmission between the engine and the gearbox. These replace the torque converter of the conventional automatic gearbox. Their shifting is matched in such a
way that there are no jerks when shifting
the gear and the power transmission of the engine to the front wheels is not interrupted.Information for driving with the automatic gearbox DSG Shifting up and down through the gears is performed automatically.You can also, however, switch the gearbox over into the
Tiptronic mode
. This mode
makes it possible for you to also shift gears manually
⇒page 124.
Starting-off and Driving– Depress the brake pedal fully and keep it depressed. – Press the Shiftlock button (button in ha
ndle of the selector lever), move the
selector lever into the
desired position, e.g.
D ⇒page 122, and then release the
Shiftlock button.
– Release the brake pedal and depress the accelerator
⇒
.
Stopping for a short time– The selector lever position
N does not have to be selected when stopping just for
a short time, such as at a cross roads. It
is sufficient to hold
the vehicle stationary
using the foot brake. The engine can, however, be allowed just to idle.
Parking– Depress the brake pedal and hold it depressed.
– Apply the handbrake firmly. – Press and Shiftlock button in the selector lever, move the selector lever to
P and
then release the Shiftlock button.
The engine can only be
started
when the selector lever is in position
P or N
⇒ page 110. At temperatures below -10 °C the engine can only be started in the selector lever position
P.
It is sufficient to engage selector lever position
P when parking on a flat surface. When
parking on a slope you should first apply
the handbrake firmly and then move the
selector lever into position
P. This is to ensure that there is no excessive pressure acting
on the lock mechanism and that it is easier to subsequently move the selector lever out of position
P.
If the selector lever position
N is selected by accident while driving it is first necessary
to release pressure on the accelerator pedal and wait for idling speed of the engine to be reached before engaging a driv
e position in the selector lever.
WARNING
•
Do not depress the accelerator when changing the position of the selector
lever if the car is stationary and the engine is running - risk of accident!•
Never move the selector lever into position R or P when driving - risk of an
accident!•
If you are stopping at a hill (downhill section), never try to hold the car
stationary with the gear engaged by mean
s of the “accelerator”, this means by
letting the clutch slip. This can lead to ov
erheating of the clutch
. If there is a risk
of overheating of the clutch due to overlo
ad, the clutch is op
ened automatically
and the vehicle rolls backward - risk of accident!•
If yo u m us t s to p a t a sl ope , d e pre s s a nd ho ld t he b ra ke pe d a l , s o t ha t y ou c a n
prevent the vehicle from rolling back.
sgg.6.book Page 121 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
170
Note
The tyre inflation pressure-control system:•
does not replace the regular tyre inflatio
n pressure control, because the system
cannot detect an even pressure loss;•
cannot warn in case of very rapid tyre inflation pressure loss, e.g. in case of sudden
tyre damage. In this case carefully bring the vehicle to a standstill without sudden steering movements and without sharp braking.•
In order to ensure a proper functioning
of the tyre inflation pressure-control
system, it is necessary to carry out the basic setting again every 10 000 km or 1x a year.Diesel particle filter* (diesel engine)In the diesel particle filter the resu
lting soot particles are collected and
burnt during the combustion of diesel fuel.Code
7GG
, 7MB
or 7MG
on the vehicle data sticker, see
⇒fig. 157
, indicates that your
vehicle is equipped
with a diesel particle filter. The ve
hicle data sticker is located on
the floor of the luggage compartment and is also stated in the Service schedule. The diesel particle filter filters the soot particles completely from the exhaust. The soot is collected in the diesel particle filter and
burnt regularly. To assist this procedure, we
recommend not to drive regu
larly over short distances.
If the diesel particle filter is clogged or there
is a fault, it is indicated by the warning light

.
WARNING
•
The diesel particle filter
achieves very high temp
eratures. Therefore do not
park at points where the hot filter comes into direct contact with dry grass or other combustible materials - risk of fire!•
Never use additional underbody protection or corrosion-protection agents
for the exhaust pipes, catalytic converters,
diesel particle filter
or heat shields.
When the engine reaches its operating
temperature, these
substances might
ignite - risk of fire.
Note
•
When using diesel fuel with high sulphur cont
ent the life of the diesel particle filter
is clearly reduced. A specialist garage will
be able to tell you which countries use only
diesel fuel with high sulphur content.Off-road*GeneralThe Off-road mode comprises functions which assist off-road driving. The following functions are integrated in the Off-road mode:•
Start-Off Assist
⇒page 171,
•
Downhill Drive Support
⇒page 171,
•
EDL Off-road
⇒page 164,
Fig. 157 Vehicle data sticker
Fig. 158 Off-road switch
sgg.6.book Page 170 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
193
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
General MaintenanceTaking care of your vehicle and cleaning the vehicleGeneralProper care retains the value of your vehicle.Regular and proper care retains
the value
of your vehicle. It may also be one of the
requirements for the acceptance of warranty
claims relating to corrosion damage and
paint defects on the bodywork. We recommend using a preserva
tive from Škoda genuine accessories offered by your
Škoda dealer. Please follow the instructions for use on the package.
WARNING
•
Care products may be harmful to your health if not used according to the
instructions.•
Always store care products in a safe place, out of the reach of children - risk
of poisoning!
For the sake of the environment
•
Always select environmentally-friendly
products when purchasing vehicle care
products.•
Do not dispose of the packages with residues of care products in domestic waste.
Care of the exterior of vehicleWashing the vehicle Frequent washing protects your vehicle.The best protection for your vehicle agai
nst harmful environmental influences is
frequent
washing and wax treatment. How of
ten you should wash your vehicle
depends on a wide range of factors, such as:
•
Frequency of use,
•
The parking situation (garage, below trees etc.),
•
Season of the year,
•
Weather conditions,
•
Environmental influences.
The longer insect residues, bird droppings, tree sap, road and industrial dust, tar, soot particles, road salt and other aggressive deposits remain adhering to the paintwork of your vehicle, the more detrimental their destructive effect can be. High temperatures, such as those caused by intensive sun'
s rays, accentuate this caustic effect.
It may therefore be necessary, in ce
rtain circumstances, to wash the car
once a week
.
It may also be sufficient, however, to wash the car
once a month
followed by appro-
priate wax treatment. It is essential to also thoroughly wash the
underside of your vehicle
at the end of the
winter road salting and gritting period.
WARNING
When washing your vehicle in the winter
: Water and ice in the brake system can
affect the braking efficiency - risk of accident!Automatic vehicle wash systemsThe paintwork of the vehicle is sufficiently resistant that the vehicle can be washed normally in automatic vehicle wash plants
without any problem. The actual stress to
which the paintwork is subjected, however, depends greatly on the design of the vehicle wash system, the filtering of the wa
ter and the type of washing and care prod-
ucts used. If the paintwork of
your vehicle appear
s mat after being washed or even has
scratches, point this out to the operator of the vehicle wash plant. Use a different vehicle wash plant, if necessary.
sgg.6.book Page 193 Thursday, September 24, 2009 2:32 PM

Breakdown assistance
225
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Changing a wheelPreliminary workThe following steps should be carried ou
t before actually changing the wheel.
– If it is necessary to change a wheel, park
the vehicle as far aw
ay as possible from
the traffic flow. The place you choose should be
level
.
–Have
all the occupants get out.
While changing a wheel, the occupants of the
vehicle should not stand on the ro
ad (e.g. behind a crash barrier).
– Apply the
handbrake
firmly.
–Engage
1st gear
or if your vehicle is fitted with
an automatic gearbox, position the
selector lever into position P
.
– If a trailer is coupled, uncouple it. –Take the
vehicle tool kit
⇒page 223 and the
spare wheel*
⇒page 224 out of the
luggage compartment.
WARNING
•
If you find yourself in flowing traffic switch on the hazard warning lights
system and place the warning triangle on
the side of the road at the prescribed
distance from your vehicle while observing all national legal provisions. In this way you are protecting not only yourself but also other road users.•
Never start the engine with the vehicle si
tting on the raised
jack - danger of
suffering injury.
Caution
If you have to change a wheel on a slope first block the opposite wheel with a stone or similar object in order to secure the
vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.
Changing a wheelAlways change a wheel on a level surface as far as possible. – Take off the full wheel trim*
⇒page 226 or the caps
⇒page 226.
– In the case of light alloy wheels remove the wheel trim cap
⇒page 227.
– First of all slacken the safety wheel bolt * and afterwards the other wheel bolts
⇒ page 227.
– Jack up the vehicle until the wheel to
be changed is clear of the ground
⇒ page 227.
– Unscrew the wheel bolts and place them
on a clean surface (cloth, paper etc.).
– Take off the wheel. – Fit on the spare wheel and tighten the wheel bolts slightly.– Lower the car. – Tighten the wheel bolts firmly, alternatel
y and diagonally using the wheel wrench
(crosswise) and last the safety wheel bolt*
⇒page 227.
Note
•
All bolts must be clean and must turn easily.
•
You must never grease or oil the wheel bolts!
•
When fitting on unidirectiona
l tyres, ensure that the tyres rotate in the correct
direction
⇒page 215.
Subsequent stepsAfter changing the wheel, you mu
st perform the following steps.
– Stow the vehicle tool kit in the space provided.– Stow the replaced wheel in the luggage compartment. –
Check
the
tyre pressure
on the spare wheel just mounted as soon as possible.
sgg.6.book Page 225 Thursday, September 24, 2009 2:32 PM