2009 SKODA YETI high beam

Lights and Visibility
55
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rain lights If you switch on the windscreen wipe in th
e operation rain sensor* for longer than 10
seconds or in the operation permanent wipe (position 2 or 3)
⇒page 63 switching on
for longer than 15 seconds, the side lights
and low beam are switched on automati-
cally. The light switches off if the windscreen wipe is in operation rain sensor* for more than 4 minutes or is not switched
on in the operation permanent wipe.
WARNING
The automatic light control only operat
es as a support. Th
e driver is not
released from his responsibility to inspect the light and if necessary to switch on the light depending on the light conditions. The light sensor cannot detect for example rain or snow. For these conditions we recommend to switch on the low beam
!
Note
•
Do not affix any stickers in front of the light sensor, so that you do not impair its
function or put it out of operation.•
The same principles as for using the automa
tic light control also
apply to the light
which is switched on manually
⇒page 53.
Cornering lights*The cornering lights are used to illuminate
the curves by means of the cone of light
swiveling together with the front headlight with Xenon lights*. This function is active when the speed of the car increases to more than 10km/h. The swiveling function of the headlights ca
n be switched off / on via the menu point
Assistant
in the main menu of the Information display*
⇒page 24.
WARNING
If the cornering ligh
ts are defective, the headlights are automatically lowered to
the emergency position, which prevents a
possible dazzling of oncoming traffic.
Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immediatel
y by a specialist garage.
Coming Home FunctionThe function makes it possible to switch on the lights in the darkness for a short time after leaving the vehicle.Switching on Coming Home Function– The light switch is in the position automatic driving lamp control

and the low
beam illuminates.
– Switch off the ignition. – After opening the driver's door, the function Coming Home is switched on.– Close all the doors and the boot lid and lo
ck the vehicle. After a short time, switch
all lights off.
Depending on equipment fitted the function Coming Home switches on the following lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Coming Home Function The lights go out 10 seconds after cl
osing all the doors and the boot lid.
If a door or the boot lid re
mains open, the lights go out
60 seconds after switching off
the ignition. The function Coming Home is controlled with the light sensor in the mount of the inte- rior rear mirror. If the light intensity is higher than the set value of the light sensor, the Coming Home Function is not switched on after switching off the ignition.
Note
•
If the Coming Home Function is switched
on constantly, the battery will be heavily
discharged particularly in short-haul traffic.•
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
sgg.6.book Page 55 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
56•
You can change the illumination period
for the Coming Home Function by means
of the information display*.Leaving Home FunctionThis function makes it possible to switch
on the lights when approaching the vehicle.
Switching on Leaving Home Function– Unlock the vehicle with the radio remote control - the lights come on. Depending on equipment fitted
the function Leaving Home switches on the following
lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Leaving Home Function The function Leaving Home is
controlled with the light sensor in the mount of the inte-
rior rear mirror. If the light intensity is higher than the set value of the light sensor, the Leaving Home Function is not switched on
after unlocking the vehicle with the radio
remote control. After unlocking the vehicle with the radio remote control, the lights come on for 10 seconds. The Leaving Home Function is also
switched off after the ignition is switched
on and after locking the vehicle. If no door is opened within 30 seconds, the lights go out and the vehicle is locked auto- matically.
Note
•
If the Leaving Home Function is switched
on constantly, the batt
ery will be heavily
discharged particularly
in short-haul traffic.
•
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
•
You can change the illumination period
for the Leaving Home Function by means
of the information display*.Tourist light*Xenon headlight This mode makes it possible to drive in countries with opposing traffic system, driving on the left/right, without dazzling the oncoming vehicles. When the mode “tourist light” is active, the side to side swivel of the headlights is deactivated. The mode “tourist light” is activated / deactivated via the information display* in the menu:„
SETUP (Settings)
„
Tra v e l m o d e„
Off
„
On
Halogen headlight When using Halogen headlights, it is necessary to stick a sticker over a certain part of the headlights in order to prevent the dazzling of oncoming traffic. You can purchase headlight stickers from the range of the Škoda original accessories.Fog lights*

Fig. 46 Dash panel: Light switch
sgg.6.book Page 56 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
57
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Switching on the fog lights– First of all turn the light switch into position
 or  ⇒page 56, fig. 46
.
– Pull the light switch into position . The rear fog light warning light
 ⇒page 29 lights up in the instrument cluster when
the fog light is switched off.Fog lights with the function “Corner”* The fog lights with the function “Corner” improve the illumination of areas close to the vehicle when turning, parking etc.The fog lights with the function “Corner” ar
e regulated according to the steering angle
or after switching on the turn signal light
8) in the following circumstances:
•
the vehicle is stationary and the engine
is running or it moves with a speed of
maximum 40 km/h;•
the daylight driving lights are not switched on;
•
the low beam is switched on or th
e light switch is
in the position

and the
intensity of the ambient light causes the low beam to be switched on;•
the fog lights are not switched on;
•
no reverse gear is engaged.Note
If you engage the reverse gear during the
active function “Corne
r”, both fog lights
illuminate.Rear fog light

Switching on the rear fog light– First of all turn the light switch into position
 or  ⇒page 56, fig. 46
.
– Pull the switch into position .
The rear fog light warning light
 ⇒page 29 lights up in the instrument cluster when
the fog light is switched off. Only the rear fog light of the trailer lights
up automatically when you are towing a trailer
using a factory-fitted towing device
which is fitted with the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on
if visibility is partic
ularly poor (conform
with any varying legal provisions) to avoi
d dazzling vehicles behind your vehicle.
Instrument lighting*

You can adjust the brightness of the instrument lighting.Instrument lighting– Switch on the light. – Turn the control dial
⇒fig. 47
to the desired intensity of the instrument lighting.
For the information display*
⇒page 24 the intensity of the lighting is automatically
set. It is only possible to adjust the instrume
nt lighting with the co
ntrol dial if the light
intensity drops below the set value of the light sensor.
8)If both switch on versions are conflicting, for ex
ample if the steering wheel is turned to the left
and the right turn signal light is switched on, the turn signal light has the higher priority.
A1
A2
Fig. 47 Dash panel:
Instrument lighting
sgg.6.book Page 57 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
179
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
HeadlightThe low beam of your headlights is set asymmetrically. It illuminates the side of the road on which you are driving to a greater ex
tent. If you drive abroad on the other side
of the road, you will
dazzle oncoming traffic.
In order to prevent the dazzling of oncoming traffic, it is necessary that an adjustment of the headlights is carried out by a specialist garage. The adaptation of the headlights with Xenon
lights* (applies only to
vehicles which are
designed for driving on the right and on the left) is performed in the menu
Setup

Tr a v e l m o d e
in the main menu of the Information display*
⇒page 24.
Note
You can obtain further information regarding masking over the headlights from a specialist garage.Avoiding damage to your vehicleWhen driving on poor roads and lanes or
when driving over kerbstones, steep ramps
etc., you must pay particular attention to
ensuring that any low-slung parts of the
vehicle, such as spoiler and exhaust,
do not touch the ground and get damaged.
This particularly applies to
models with a lowered suspen
sion (sport suspension) and
also when your vehicle is fully laden.Driving through bodies of water on roads
In order to avoid damage to the vehicle wh
en driving through bodies of water (e.g.
flooded roads), observe the following:•
Determine the depth of the water when driv
ing through bodies of water. The water
can reach at the maximum the web on the lower sill of the vehicle
⇒fig. 162
.
•
Drive no more than at walking speed. At a higher speed, a water wave can form in
front of the vehicle which can cause water to
penetrate into the air induction system of
the engine or into other parts of the vehicle.•
Never let the vehicle stand in the water,
never drive backwards and do not switch
off the engine.
WARNING
•
Driving through water, mud, sludge etc. can reduce the braking power and
extend the braking distance - risk of accident!•
Avoid sudden and severe braking manoeuvres immediately after driving
through bodies of water.•
After driving through bodies of water, the brakes must be cleaned and dried
as soon as possible by intermittent braking. Only apply the brakes for the purpose of drying and cleaning the brake
discs if the traffic conditions permit
this. Do not place any other road users in jeopardy.
Caution
•
When driving through bodies of water, pa
rts of the vehicle such as the engine,
gearbox, catalytic converter, chassis
or electrics can be severely damaged.
•
Oncoming vehicles can gene
rate water waves which ca
n exceed the permissible
water level for your vehicle.•
Potholes, mud or rocks can be
hidden under the water making it difficult or impos-
sible to drive through the body of water.•
Do not drive through salt water. The salt
can lead to corrosion. Immediately rinse
all the parts of the vehicle, which came into
contact with the salt water, with fresh
water.
Fig. 162 Crossing bodies of water
sgg.6.book Page 179 Thursday, September 24, 2009 2:32 PM

Towing a trailer
191
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Headlights Before starting off with a hitched trailer, also check the setting of the headlights. Alter the setting as necessary with the ai
d of the headlight beam adjuster
⇒page 58.
Detachable ball head The ball rod is detachable on vehicles which
feature a factory-fitted
towing device. It is
stowed together with separate fitting instru
ctions in the spare wheel well in the luggage
compartment of the vehicle. Further information on the towing device
⇒page 192.
Note
•
We recommend that you also have your
vehicle inspected between service inter-
vals if you tow a trailer frequently.•
The handbrake on the towing vehicle must be put on when coupling and decou-
pling the trailer.Driving Tips Particular caution is required when towing a trailer.– Do not, as far as possible, drive with
your vehicle unladen and the trailer laden.
– Do not make full use of the legal maximum speeds. This applies in particular to
downhill sections.
– Apply the brakes in good time. – Keep a check on the coolant temperature gauge if the outside temperature is high. Distribution of weight The distribution of the weight
is very poor if your vehicle
is unladen and the trailer is
laden. Maintain a particularly low speed if you cannot avoid driving with this combina-tion. Driving speed Do not drive faster than 80 km/hour for safety reasons. This also applies for countries in which higher speeds are allowed.
The fact that the driving stability of the vehicle + trailer combination reduces with increasing speed means that the legally allowed speed should not be used when there are unfavourable road, weather or wind cond
itions, particularly near accident black
spots. You must always reduce your speed immediat
ely as soon as you detect even just the
slightest swaying
of the trailer. On no account attempt to stop the trailer from
“swaying” by accelerating. Apply the brakes in good time! If
the trailer is fitted with a
trailer brake
, apply the
brakes gently at first and then brake firmly. This will avoid brake jolts resulting from the trailer wheels locking. Shift down gears in good time before negotiating a downhill section to allow the engine to also act as a brake. Engine overheating Please keep a check on the coolant temperature gauge if you have to negotiate a lengthy slope in a low gear at a high engi
ne speed when the outside temperature is
very high
⇒page 17, “Coolant temperature gauge”.
If the needle of the coolant temperature gauge moves into the right-hand area or even the red area of the scale, reduce your speed immediately. Stop and switch off the engine if the warning light
 in the instrument cluster begins flashing. Wait a few
minutes and check the level of coolant in the coolant expansion bottle
⇒page 207,
“Inspecting the coolant level”. Please refer to the following guidelines
⇒page 34, “Coolant temperature/ Coolant
quantity
”.
The coolant temperature can be reduced by switching on the heating.Any increase in the cooling effect of the coolant fan through shifting down a gear and increasing the engine speed is not possible
since the fan speed is independent of the
engine speed. One should also not drop a gear
for this reason when towing a trailer as
long as the engine can manage th
e slope without any drop in speed.
sgg.6.book Page 191 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
239
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
Bulbs H7 and H4 are pressurised and
may burst when changing the bulb -
risk of injury!•
It is recommended to wear gloves and
safety glasses when changing a bulb.
•
Gas discharge bulbs* (xenon bulbs) op
erate with a high voltage, profes-
sional knowledge is required - danger to life!
Caution
Do not take hold of the glass bulb with naked fingers (even the smallest amount of dirt reduces the working life of the light bulb).
Use a clean cloth, serviette or something
similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed that no major complications will
arise. Other light bulbs should be replaced by your
specialist garage.
Front headlightPositions of the light bulbs in the front headlight
⇒fig. 197
.
- Fog lights and daylight driving lights - Parking lights (Xenon headlight) - Parking lights (halogen headlight), low beam lights and main beam lightsTurn signal light at the frontYou should have the light bulb of the front
turn signal light replaced by a specialist
garage.Parking light at the frontFig. 198 Remove cap / removing the fixtur
e for the parking light (halogen headlight)
Luggage compartment light
W5W
Door warning light
W5W
Lighting in storage compartment on front passenger side
C3W
Others
Bulb
Fig. 197 Front headlight: Fitting position of the bulbs
AAABAC
sgg.6.book Page 239 Thursday, September 24, 2009 2:32 PM