2009 SKODA YETI wheel size

Seats and Stowage
69
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Seats and StowageFront seatsBasic informationThe front seats have a wide range of differ
ent settings and can thus be matched to the
physical characteristics of the driver and
front passenger. Correct adjustment of the
seats is particularly important for:•
safely and quickly reaching the controls;
•
a relaxed, fatigue-free body position;
•
achieving the maximum protection offered by the seat belts and the airbag
system.
WARNING
•
Never transport more occupants than the maximum seating in the vehicle.
•
Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened
⇒page 156, “Transporting children safely” with a
suitable restraint system.•
The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be correctly fastened in order to provide an optimal protection for you and your occupants.•
Always keep your feet in the footwell
when the vehicle is being driven -
never place your feet on the instrument panel, out of the window or on the surfaces of the seats. This is particular
ly important for the front seat passenger.
You will be exposed to increased risk of
injury if it becomes necessary to apply
the brake or in the event of an accident.
If an airbag is deployed, you may suffer
fatal injuries when adopting an incorrect seated position!•
It is important for the driver and front
passenger to maintain
a distance of at
least 25 cm from the steering wheel or
dash panel. Not maintaining this
minimum distance will mean that the airbag
system will not be able to properly
protect you - hazard! The front seats and the head restraints must always also be correctly adjusted to match the body size of the occupant.
•
Ensure that there are no objects in
the footwell as any objects may get
behind the pedals during a driving or braking manoeuvre. You would then no longer be able to operate the clutch, to brake or accelerate.•
Do not transport any objects on the front passenger seat except those
provided for this purpose (e.g. child safety seat) - risk of accident!Adjusting the front seatsAdjusting a seat in a forward/back direction–Pull the lever
⇒fig. 62
up and push the seat into the desired position.
– Release the lever and push the seat further until the lock is heard to engage.Adjusting height of seat– Lift the seat if required by pulling or pumping lever upwards.– Lower the seat if required by pushing or pumping lever downwards.Adjust the angle of the seat backrest– Relieve any pressure on the seat backrest (do not lean on it) and turn the hand-
wheel
⇒fig. 62
to adjust the desired angle of the backrest.
WARNING (continued)
Fig. 62 Controls at seat
A1A1
A2A2
A3
sgg.6.book Page 69 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
115
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
set so that the play function volume decr
eases when activating the parking aid, see
Owner's Manual radio* or na
vigation system*. This impr
oves the audibility of the
parking aid. Activating The parking aid is activated when the
reverse gear
is engaged and the ignition is
turned on or by pressing the button
⇒page 114, fig. 118
- the symbol lights up in
the button. The activation is confirme
d by a brief acknowledgement signal.
Deactivating The parking aid is deactivated after pressing the button°
⇒page 114, fig. 118
or at
a speed of more than 10 km/h - the symbol
 in the button is no longer illuminated.
WARNING
•
The parking aid is not a substitute for the driver paying proper attention and
it is always the driver's responsibility to
take care when reversing the vehicle or
carrying out similar manoeuvres.•
You should therefore satisfy yourself, befo
re reversing, that there is no small
obstacle, such as a rock, thin post, trailer drawbar etc., in front or behind your vehicle. Such an obstacle might not be
within the range dete
cted by the sensors.
•
Under certain circumstances, surfaces
of certain objects and types of
clothing cannot reflect the signal of th
e parking aid. Thus, these objects or
people who wear such clothing are not re
cognised by the sensors of the parking
aid.
Note
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing device*).•
If a warning signal sounds for about 3 seco
nds after activating the system and there
is no obstacle close to your
vehicle, this indicates a system fault. The fault is confirmed
additionally when the symbol flashes in the button
⇒page 114, fig. 118
. Have the
fault rectified by a specialist workshop.•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.
•
If the parking aid is activated and the sele
ctor lever of the automatic gearbox is in
the position , warning signal indicates inte
rruption (vehicle can no longer move).
Park Assist*Description and important informationThe park assist assists you when parking in a suitable parallel parking space between two vehicles or
behind a vehicle.
The park assist automatically searches for
suitable parking spaces
after switching on
the ignition and when driving up to 30 km/h. During the parking procedure the park assist only takes over the steering movements, the pedals continue to be operated by the driver. Function of the system is based on:•
Length and depth measurement of the parking spaces when driving
•
Evaluation of the size of the parking space
•
Definition of the correct position of the vehicle for parking
•
Calculating the line on which the vehicle drives backwards into the parking space
•
Actuation of the steering force assistance, automatic spinning of the wheels of the
front axle when parking.
WARNING
The park assist does not take away the responsability from the driver when parking.•
Pay particular attention to small children and animals as they would not be
recognised by the sensors of the parking aid.•
Under certain circumstances, surfaces of certain objects and types of
clothing cannot reflect the signal of the park assist or the parking aid. Thus, these objects or people who wear such clothing are not recognised by the sensors of the parking aid.



AP
sgg.6.book Page 115 Thursday, September 24, 2009 2:32 PM

Starting-off and Driving
116
•
The external sound source of the park
assist and the parking aid can be
disruptively influenced and under unfavourable conditions, objects or people cannot be recognised by the sensors of the parking aid.
Caution
•
If other vehicles are parked behind or on
the kurb, the park assist guides your
ve hicle be yond the kurb or onto it. Make s ure that the whee ls or the whe el rims of yo ur vehicle are not damaged and if necessary intervene in time.•
You should satisfy yourself before parking that there is no small obstacle, such as a
rock, thin post, trailer drawbar etc., in front
or behind your vehicle. Such an obstacle
might not be within the range detected by the sensors.•
Under certain circumstances, surfaces or st
ructures of certain objects such as wire
mesh fences, powder snow etc..., ca
nnot be recognised by the system.
•
The evaluation of the parking space and the parking procedure depends on the
circumference of the wheels. The system does not function correctly if your vehicle is mounted with wheels of non-permissible
size, snow chains or a temporary spare
wheel (in order to reach the nearest workshop). If the tyres other than those excepted by the manufacturer are mounted, the resulting position of the vehicle in the parking space can differ slightly. The parking assistant system automatically performs the correction of the wheel circumference when driving.•
The accuracy of the evaluation for the parking space can be influenced by the
incorrectly determined outside temperature if
the later is influenced by the thermal
radiation of the engine i.e for stop and go in a traffic jam.•
In order to avoid damaging th
e sensors while cleaning wi
th high-pressure cleaners
or steam jets, the sensors must only be
directly sprayed for short periods while a
minimum distance of 10 cm must be observed.
Note
•
A component of the park assist is the front and rear parking aid*.
•
The electronic stability programme (ESP*)
must always be switched on for the
parking procedure.
•
Only the front parking aid operates if yo
u are towing a trailer (applies only to
models which feature a factory-fitted towing de
vice*). This is why it is not possible to
park backwards with the help of the
park assist when towing a trailer.
•
The sensors must be kept clean and free of ice to enable the parking aid to operate
properly.Switch on display of the park a
ssist in the information display*
Fig. 119 Switching on the park assist / information display: Finding a suitable parking spaceSwitch on display of the park assist in the information display*– Press the button
⇒fig. 119
.
– Drive past the parking row up to maximum 30 km/h and with a distance of 0.5 m to
1.5 m
⇒fig. 119
.
Operate the turn signal for the driver's side if
you wish to park on this side of the road.
In the information display* the search area
for the parking space is indicated on the
driver's side. If you press the button at a speed greate
r than 30 km/h and less than 50 km/h, the
message indicating that the speed for detecting the space is exceeded will be displayed in the information display of the in
strument cluster. If the speed drops below
30 km/h, the condition of the parking assistant is automatically displayed in the infor-mation display of the instrument cluster. When exceeding the speed of 50 km/h, it is required to activate the displa
y again by pressing the button
⇒fig. 119
.
WARNING (continued)
sgg.6.book Page 116 Thursday, September 24, 2009 2:32 PM

Passive Safety
138
•
Ensure that the lighting and the turn signal system are functioning properly.
•
Inspect the tyre inflation pressure.
•
Ensure that all the windows offer
a good visibility to the outside.
•
Safely attach the items of luggage
⇒page 78, “Loading the luggage compartment”.
•
Ensure that no objects can obstruct the pedal.
•
Adjust the mirror, the front seat and the head restraint to match your body size.
•
Point out to your occupants that the head
restraints must be adjusted to match
their body size.•
Protect the children in suitable child seats with correctly fastened seat belts
⇒ page 156, “Transporting children safely”.•
Adopt the correct seated position
⇒page 138, “Correct seated position”. Also
inform your occupants to adopt the correct seated position.•
Fasten the seat belt correctly. Also inform your occupants to properly fasten the
seat belts
⇒page 143, “How are seat be
lts correctly fastened?”.
What influences the driving safety? The driving safety is primarily determined by the style of driving and the personal behaviour of all the occupants.The driver is fully responsible for himself an
d his occupants. If yo
ur driving safety is
effected, you place yourself and the oncomi
ng traffic at risk. Please refer to the
following guidelines.•
Do not get distracted from concentrating on the traffic situation, e.g. by your occu-
pants or mobile phone calls.•
Never drive when your driving ability is impaired, e.g. through medication, alcohol,
drugs.•
Keep to the traffic regulations and the permissible speed limit.
•
Adjust the driving speed at all times to the road condition as well as to the traffic
and weather conditions.•
Take regular breaks on long journe
ys - at the latest every two hours.
Correct seated positionCorrect seated position for the driver Correct seated position for the driver is important for safe and relaxed driving.Fig. 131 The correct distance of
the driver from the steering wh
eel / the correct head restraint
adjustment for the driverFor your own safety and to reduce the risk of injury in the event of an accident, we recommend the following setting.•
Adjust the steering wheel so that the distance between the steering wheel and your
chest is at least 25 cm
⇒fig. 131
on the left.
•
Position the driver seat in the forward/back direction so that you are able to fully
press the pedals with your legs at a slight angle.•
Adjust the seat backrest so that you are able to reach the highest point of the
steering wheel with your arms at a slight angle.•
Adjust the head restraint so that the top edge of the head restraint is at the same
level as the upper part of your head
⇒fig. 131
on the right.
•
Fasten the seat belt correctly
⇒page 143, “How are seat belts correctly fastened?”.
Manual driver se
at adjustment
⇒page 12, “Adjusting the front seats”.
Electrical driver seat adjustment
⇒page 70, “Adjusting front seats electrically*”.
sgg.6.book Page 138 Thursday, September 24, 2009 2:32 PM

Passive Safety
139
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be correctly fastened in order to provide an optimal protection for you and your occupants.•
The driver must maintain a distance of
at least 25 cm to
the steering wheel
⇒ page 138, fig. 131
. Not maintaining this minimum distance will mean that
the airbag system will not be able to properly protect you - hazard!•
When driving, hold the st
eering wheel with both hands firmly on the outer
edge in the 9 o'clock and 3 o'clock po
sition. Never hold
the steering wheel
firmly in the 12 o'clock position or in another way (e.g. in the middle of the steering wheel or at the inner steering wheel
edge). In such cases, injuries to the
arms, the hands and the head can occur
when the driver airbag is deployed.
•
The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the se
at belts and of the airbag system - risk
of injury!•
Ensure that there are no objects in
the footwell as an
y objects may get
behind the pedals during a driving or
braking manoeuvre. You would then no
longer be able to operate the
clutch, to brake or accelerate.
Correct seated position for the front passenger The f ro n t p as s en ger mus t mai n tai n a d i s tan ce of a t l ea s t 25 c m f rom th e dash panel so that the airbag offers him the greatest possible safety it is deployed.For the safety of the front pass
enger and to reduce the risk of injury in the event of an
accident, we recommend
the following setting.
•
Adjust the front passenger seat as
far as possible to the rear.
•
Adjust the head restraint so that the top ed
ge of the head restraint is at the same
level as the upper pa
rt of your head
⇒page 138, fig. 131
.
•
Fasten the seat belt correctly
⇒page 143, “How are seat belts correctly fastened?”.
In exceptional cases the front pass
enger airbag can be deactivated
⇒page 154,
“Deactivating an airbag”.
Manual front passenger adjustment
⇒page 12, “Adjusting the front seats”.
Electrical front passenger seat adjustment
⇒page 70, “Adjusting front seats electri-
cally*”.
WARNING
•
The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be correctly fastened in order to provide an optimal protection for you and your occupants.•
The front passenger must maintain a distance of at least 25 cm to the dash
panel. Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you - hazard!•
Always keep your feet in the footwel
l when the vehicle is being driven -
never place your feet on the instrument panel, out of the window or on the surfaces of the seats. You will be exposed to increased risk of injury if it becomes necessary to apply the brake or in the ev
ent of an accident. If an airbag is
deployed, you may suffer fatal injuries wh
en adopting an incorrect seated posi-
tion!•
The seat backrests must not be angled
too far back when driving otherwise
this will affect proper operation of the se
at belts and of the airbag system - risk
of injury!Correct seated position for the occupants on the rear seats Occupants on the rear seats must sit upright, keep the feet in the foot- well and must have their se
at belts correctly fastened.
To reduce the risk of injury in the event of
a sudden braking manoeuvre or an accident,
the occupants on the rear seats must observe the following:•
Adjust the head restraints so that the top edge of the head restraints are at the same
level as the upper part of your head
⇒page 138, fig. 131
.
•
Fasten the seat belt correctly
⇒page 143, “How are seat belts correctly fastened?”.
•
If you are transporting
⇒page 156, “Transporting children safely” children in the
vehicle, please use a suitable child restraint system.
sgg.6.book Page 139 Thursday, September 24, 2009 2:32 PM

Airbag system
148
Apart from their normal protective function, a further task of the
seat belts
is to also
hold the driver and front passenger in a correct seated position in the event of a frontal collision so as to enable the front ai
rbags to offer the maximum protection.
You should therefore always fasten the seat be
lts, not only because this is required by
law, but also for safety reasons and for your own protection
⇒page 141, “Why seat
belts?”.
Note
The dash panel must be replaced after the front passenger airbag has been deployed.Function of the front airbags Risk of injury to the head and ches
t area is reduced by fully inflated
airbags.The airbag system is designed in such a wa
y that the airbags for the driver and front
passenger are deployed in the event of a violent frontal collision. In certain accident situations, the front, side
, knee and head airbag are simultaneously
deployed. If the airbags are deployed, the airbags are filled with a propellant gas and inflated in front of the driver and front passenger
⇒fig. 138
. The airbags inflate in fractions of a
second and at a high speed in order to be able
to offer that additional protection in the
event of an accident. The forward movement of the driver and of the front passenger
i s c us h i o n e d w h e n th e y m a ke co n t a c t w i t h t h e f u l l y i n f l a t e d a i r ba g a n d th e r i s k o f i n j u r y to head and chest is thus reduced. The specially developed airbag allows the gas
to flow out of the inflated airbag in a
controlled manner (depending on the load of
the particular car occupant) in order to
cushion head and chest areas. The airbag then
deflates subsequently to such an extent,
after an accident, to again provide a clear view forward. A grey white, non harmful gas is released when airbag is inflated. This is perfectly normal and is not an indicati
on of a fire in the vehicle.
The airbag develops enormous forces when triggered, which can lead to injuries if the sitting position or seated position is not correct
⇒page 148.
Important safety information regarding the front airbag system Correct use of the airbag system cons
iderably reduces the risk of injury!
WARNING
•
Never transport children on the front seat of a vehicle without using a
proper restraint system. If airbags are de
ployed in the event of an accident, the
child might suffer severe
or even fatal injuries!
•
For the driver and front passenger it is important to maintain a distance of
at least 25 cm from the steering wheel or dash panel
⇒fig. 139
. Not main-
taining this minimum distance will mean that the airbag system will not be able to properly protect you - hazard! The front seats and the head restraints must always also be correctly adjusted to match the body size of the occupant.
Fig. 138 Inflated airbags
Fig. 139 Safe distance to steering wheel
sgg.6.book Page 148 Thursday, September 24, 2009 2:32 PM

Wheels and Tyres
215
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Wheels and TyresWheelsGeneral information•
New tyres do not offer optimal grip at first and should therefore be run in for about
500 km at a moderate speed and an appropri
ately cautious style of driving. You will
also profit from longer tyre life.•
The tread depth of new tyres may differ because of design features and the config-
uration of the tread (depending on the type of tyre and the manufacturer).•
Drive over curbs on the side of the road
and other such obstacles slowly and,
where possible, at a right angle in order to avoid damage to tyres and wheel trims.•
Inspect your tyres from time to time
for damage (punctures, cuts, splits and
bulges). Remove foreign bodies from the tyre profile.•
Damage to tyres and wheels is frequently
not visible. Unusual vi
brations or pulling
of the vehicle to one side coul
d be a sign of tyre damage.
Please reduce your speed
immediately and stop if you su
spect that a wheel is damaged.
Inspect the tyres for
signs of damage (bulges, splits, etc.). If no
visible damage is present, please drive at an
appropriately slow speed and carefully to the nearest specialist garage in order to have your vehicle inspected.•
Also protect your tyres from contact with oil, grease and fuel.
•
Immediately replace any dust caps of
the valves which have got lost.
•
Mark wheels before removing them so that
their previous dire
ction of running can
be maintained when mounted them again.•
Always store wheels or tyres which been removed in a cool, dry and, where
possible, dark place. Tyres which are not fixed to a wheel trim should be stored upright.
WARNING
•
New tyres during the first 500 km do not offer optimal grip and should
therefore be run appropriately - risk of accident!•
Never drive with damaged tyres - risk of accident!
Note
Please observe the various differing legal requirements regarding tyres.Ty re l i feThe life of your tyres very much depends on the following points: Tyre pressure The working life of tyres will be shortened considerably if the tyres are insufficiently or over-inflated and this will have an adverse
effect on the handling of your vehicle.
Correctly inflated tyres are of particular importance when travelling at
high speeds
. It
is therefore good to check the pressure at
least once a month and also before setting
off on a long trip. Please do not forget the spare wheel when checking the tyres. The tyre inflation pressures for
summer tyres
are indicated on the inside of the fuel
filler flap
⇒fig. 178
. The inflation pressures for
winter tyres
are 20 kPa (0.2 bar) higher
than those for summer tyres
⇒page 218.
The tyre pressure should be at the highest pressure specified for your vehicle at all times. Always check the inflation pressure of tyres when cold. Do not reduce the higher pres- sure of warm tyres. Adapt the inflation pressure of the tyres accordingly if your vehicle is carrying a significantly higher payload.
Fig. 178 An opened fuel filler flap with a tyre size and tyre inflation pressure table
sgg.6.book Page 215 Thursday, September 24, 2009 2:32 PM

Wheels and Tyres
217
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Changing wheels aroundIf significantly greater wear is present on the front tyres, we recommend changing the front wheels around with the rear wheels as shown in the diagram
⇒fig. 180
. You will
then obtain approximately the
same life for all the tyres.
It may be advantageous to swap the tyres ov
er “crosswise” when certain types of wear
characteristic arise on the running surface of
the tyres (but not in the case of unidirec-
tional tyres). The co-workers of the authorised Škoda Service Partners are extensively familiar with the combination possibilites. We recommend that you change the wheels around every 10 000 km in order to achieve even wear on all wheels and to obtain optimal tyre life.New tyres and wheelsTyres and wheel rims are important design elements. One should therefore use the tyres and wheel rims which have been releas
ed for use by Škoda Auto. They are exactly
matched to the vehicle type and therefore
contribute significantly to good road
holding and safe driving characteristics
⇒
.
Only fit radial tyres of the same type on all 4 wheels, size (rolling circumference) and, if possible, the same tread pattern on one axle. The authorised Škoda Service Partners have
access to the most current information
about which tyres we have rele
ased for use on
your vehicle.
We recommend that you have any work relati
ng to tyres or wheels carried out by an
authorised Škoda Service Partner
. The authorised Škoda Service Partners have all of
the necessary special tools and replacement pa
rts available plus the required specialist
knowledge and are also in a position to pr
operly dispose of the old tyres. A large
number of authorised Škoda Service Partners also have an attractive range of tyres and wheels available. The tyre/wheel combinations which are appr
oved for your vehicle are indicated in
your vehicle documents. Approval and licensing may differ according to the legislation prevailing in individual countries. Proper knowledge of the tyre data makes it easier for you to select the correct type of tyre. Tyres do, for example, have the following
inscription
on their walls:
225 / 50R 17 91 T
What this means is: The following
speed restrictions
apply to tyres.
The date of manufacture
is also stated on the tyre wall (possibly only on the
inside
of
wheel):
DOT ... 45 09...
Fig. 180 Changing wheels around
225
Tyre wi dt h i n mm
50
Height/width ratio in %
R
Code letter for the type of tyre -
Radial
17
Diameter of wheel in inches
91
Load index
T
Speed symbol
Speed symbol
Permissible maximum speed
S
180 km/h
T
190 km/h
H
210 km/h
V
240 km/h
W
270 km/h
Y
300 km/h
sgg.6.book Page 217 Thursday, September 24, 2009 2:32 PM