2009 SKODA YETI fog light bulb

Instruments and Indicator/Warning Lights
31
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Turn signal system

Either the left
 or right
 indicator light flashes depending on the position of the turn
signal lever. The indicator light flashes at twice its normal rate if a turn signal light fails. This does not apply when towing a trailer. Switching off the hazard warning light system
is switched on will cause all of the turn
signal lights as well as both indicator lights to flash. Further information about the turn signal system
⇒page 59.
Fog lights*

The warning light
 comes on when the fog lights are operating
⇒page 56.
Main beam

The indicator light
 comes on when the main beam is selected or also when the
headlight flasher is operated. Further information about the main beam
⇒page 59.
Low beam

The warning light
 comes on when low beam is selected
⇒page 53.
Rear fog light

The warning light
 comes on when the rear fog lights are operating
⇒page 57.
Cruise control system*

The warning light
 lights up, when operating the speed regulating system.
Bulb failure

The warning light
 comes on if a bulb is faulty:
•
up to 2 seconds after the ignition is switched on;
•
when switching on the defective light bulb.
The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The indi- cator light
 only lights up if all light bulbs of
the licence plate lighting or the parking
light (in one rear light unit) are defective.
Check regularly the function of the light
bulbs.Diesel particle filter*

(diesel engine)
If the warning light

comes on, this means that soot
has accumulated in the diesel
particle filter because of the frequent short distances. In order to clean the diesel particle filter, the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1
800 - 2 500 rpm for at least 15 minutes or until
the warning light goes out with the 4th or
5th gear engaged (automatic gearbox: posi-
tion S) when the traffic situation permits it. This increases the exhaust temperature and the soot deposited in the diesel particle filter is burnt. Always pay attention to the valid speed limits
⇒
.
The warning light

goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly
cleaned, the warning light

does not go out and the
warning light
 begins to flash. In the in
formation display* appears
Diesel-particle
Owner's manual
. Afterwards the engine control unit shifts the engine into the emer-
gency mode, which only has a reduced power
output. After switchin
g the ignition off
and on again the warning light
 comes on.
Have the vehicle inspected without
delay by your specialist garage.
sgg.6.book Page 31 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
54 Switching on daylight driving lights– Switch on the ignition without turning the light switch out of the position 0.Deactivating the function daylight driving lights– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the bottom and hold it in this position for at least 3 seconds.
Activating the function daylight driving lights– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the top and hold it in this position for at least 3 seconds.
When the daylight driving lights are switch
ed on, the side lights and the low beam
come on together. In some countries, the national legal provisions require that the parking lights come on together with the bulbs for daylight driving lights when activating the function daylight driving lights. On vehicles which are fitted with bulbs for daylight driving lights in the fog lights, the parking lights do not come on when activa
ting the function dayl
ight driving lights.
When the daylight driving lights are switch
ed on, the illumination of the instrument
cluster is switched off, however,
it is switched on in the position

when it is dark
and the low beam shines with full br
ightness (100% of the performance).
On vehicles fitted with an information displa
y*, you can also activate or deactivate in
the menu the function da
ylight driving lights:
„
Setup
„
Lights & Vision (Lights & Vision)
Automatic driving lamp control*Switching on automatic driving lamp control*– Turn the light switch
⇒fig. 45
into position

.
Switching off automatic driving lamp control*– Turn the light switch to the position 0,
 or .
If the light switch is in the position

, the symbol illuminates when the ignition is
switched on

next to the light switch. If the low beam is activated with the light
sensor, the symbol
 illuminates additionally next to the light switch.
If the light comes on automatically, the side lights and low beam as well as licence plate light light up at the same time. If the automatic light control is switched on,
the light is regulated with the light sensor
in the rear mirror holder. If the light intensity drops below the set value, e.g when driving during the day into a tunnel, the lo
w beam and the side li
ghts as well as the
licence plate light come on automatically. If
the light intensity increases again, the
lights switch off automatically. Motorway lights If the automatic light control has been swit
ched on and the vehicle speed is over 140
km/h for at least 10 seconds, the side ligh
ts and low beam are switched on automati-
cally. If the vehicle speed is below 65 km/h for at least 2 minutes, the lights are switched off.
Fig. 45 Dash panel: Light switch
sgg.6.book Page 54 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
238
For power consumers, e.g. the radio, which ca
n be operated with the ignition switched
off as long as the ignition key is not withdrawn. Electrically adjustable seats are protected by
automatic circuit breakers
, which
switch on again automatically after a few seconds after the overload has been eliminated.BulbsChanging bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Defect light bulbs should only be replaced
with light bulbs of the same type. The desig-
nation is located on the ligh
t socket or the glass bulb.
Changing certain bulbs is not something whic
h you can do yourself, but requires to be
done by a specialist. Other parts of the vehicle must be removed in order to change the light bulbs. This applies, in particular, to
bulbs which can only be reached from the
engine compartment. We therefore recommend that you have any
bulbs changed by a specialist garage or,
in exceptional cases, by calling
on other professional assistance.
Please note that the engine compartment is a hazardous area
⇒page 204, “Working
in the engine compartment”. We recommend that you always have a small box of replacement bulbs in your vehicle. You can obtain replacement bulbs from Škoda
original accessories or from a specialist
garage
18).
The set of light bulbs can be stowed
in the box in the luggage compartment.
Fitted with a xenon headlightChange of bulbs on vehicles with Xenon lights (low beam lights, parking lights and main beam lights) should be undertaken by a specialist garage. Bulb - Overview
34
Alarm, spare horn
5
35
Control unit for automatic gearbox DQ200
10
36
Not assigned
18)The small box with replacement bulbs is part of
the basic equipping of th
e vehicle in some coun-
tries.No.
Power consumer
Amperes
Front headlight
Halogen headlight
Xenon headlight
Low beam light
H4
D1S
Main beam light
H4
D1S
Parking lights
W5W
W5W BL
Daylight driving lights
P13W
Turn signals
HPC24WY
Fog lights
H7
Rear light unit
Bulb
Reversing lights, brake lights and rear fog light
P21W
Turn signals
PY21W
Parking lights
W5W
Others
Bulb
Licence plate light
C5W
3. Brake light
LED
Entry lighting
W5W
front interior lighting
W5W
Reading lights
W5W
Rear interior lighting
C5W
sgg.6.book Page 238 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
239
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
•
Bulbs H7 and H4 are pressurised and
may burst when changing the bulb -
risk of injury!•
It is recommended to wear gloves and
safety glasses when changing a bulb.
•
Gas discharge bulbs* (xenon bulbs) op
erate with a high voltage, profes-
sional knowledge is required - danger to life!
Caution
Do not take hold of the glass bulb with naked fingers (even the smallest amount of dirt reduces the working life of the light bulb).
Use a clean cloth, serviette or something
similar.
Note
This Owner's Manual only describes the replacement of bulbs where it is assumed that no major complications will
arise. Other light bulbs should be replaced by your
specialist garage.
Front headlightPositions of the light bulbs in the front headlight
⇒fig. 197
.
- Fog lights and daylight driving lights - Parking lights (Xenon headlight) - Parking lights (halogen headlight), low beam lights and main beam lightsTurn signal light at the frontYou should have the light bulb of the front
turn signal light replaced by a specialist
garage.Parking light at the frontFig. 198 Remove cap / removing the fixtur
e for the parking light (halogen headlight)
Luggage compartment light
W5W
Door warning light
W5W
Lighting in storage compartment on front passenger side
C3W
Others
Bulb
Fig. 197 Front headlight: Fitting position of the bulbs
AAABAC
sgg.6.book Page 239 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
240
Removing the light bulb for the parking light (halogen headlight)– Switch the ignition and all lights off. – Turn the protective cap in direction of arrow
OPEN
and remove it
⇒page 239,
fig. 198
.
– Pull out the fixture in direction of arrow
⇒page 239, fig. 198
.
– Take the faulty bulb out of the fixture and insert a new one.– Insert the protective cap.Removing the light bulb for the parking light (Xenon headlight)– Switch the ignition and all lights off.– Remove the rubber protective cap
⇒page 239, fig. 197
.
– Pull out the fixture in direction of arrow
⇒fig. 199
.
– Take the faulty bulb out of the fixture and insert a new one. – Insert the protective cap.
Note
In order to facilitate the removal of the fi
xture with the bulb for the parking light
(halogen headlight), we recommend to remove first of all the connector of the bulb for the low beam light.
Main beam light and low beam light– Switch the ignition and all lights off. – Turn the protective cap in direction of arrow
OPEN
⇒page 239, fig. 198
and
remove it.
– Unplug plug .– Press the wire clamps down until they
are released from the secured position.
– Remove the light bulb and insert the new light bulb in such a way that the fixing
lugs of the light bulb socket fit
into the recesses at the reflector.
Installation takes place in the reverse order.Fog lights*
Fig. 199 Removing the fixture for the parking light (Xenon headlight)A1
A2
AB
A3
Fig. 200 Removing the bulb for the main beam light and low beam light
AA
ABAC
Fig. 201 Removing the bulb for the fog light
sgg.6.book Page 240 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
241
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing the bulb for the fog light– Switch the ignition and all lights off. – Remove the rubber protective cap
⇒page 239, fig. 197
.
– Unplug plug . – Take the faulty bulb out of the fixture
by pressing the li
ght socket downwards
and insert a new one.
– Insert the protective cap.Daylight driving lightsRemove the bulb for daylight driving lights– Switch the ignition and all lights off. – Remove the rubber protective cap
⇒page 239, fig. 197
.
– Unplug plug .– Take the faulty bulb out of the fixture by turning in direction of arrow and insert
a new one in the reverse procedure.
– Insert the protective cap.
Rear light unitFig. 203 Removing the rear light unit
/ disconnecting the plug connection
– Open the boot lid. – Unscrew the light with the aid of the Torx
wrench from the vehicle tool kit. The
shorter side of the wrench is used for loosening the screws and the longer side for screwing the screws out completely
⇒fig. 203
.
– Grasp the light at the top and bottom part and pull it slightly to the rear.– Disconnect the plug connection by pressing the catches in direction of arrow
and by pulling them in direction of arrow
⇒fig. 203
.
Changing light bulbs in the rear light unitFig. 204 Remove the middle part
of the light / rear light unit:
Fitting position of the bulbs
AA
A1
A2
Fig. 202 Remove the bulb for daylight driving lights
AA
A1
A2
A1
A2
A3
sgg.6.book Page 241 Thursday, September 24, 2009 2:32 PM

Fuses and light bulbs
242
– Unscrew the securing screw with the aid of the Torx wrench and press the three
catches in direction of arrow
⇒page 241, fig. 204
.
– Remove the plastic lamp holder.– Replace the defective light bulb. – In order to replace a bulb for the brake light, reversing light, rear fog or turn signal
light, turn the fixture of the bulb to the left up to the stop and take the bulb out of the housing or pull the bulb for the parking light out of the fixture
⇒page 241,
fig. 204
.
– Change the bulb, install again the fixture with
the bulb in the housing and turn it to
the right up to the stop or insert it.
– Insert the plastic lamp holder into the
illumination unit until the interlocks are
heard to engage and screw in the securing screw with the aid of the Torx wrench ⇒ page 241, fig. 204
.
– Reconnect the plug connector and insert
the bulb in the original position.
– Screw on the light
⇒page 241, fig. 203
on the left.
Fitting position of the light bulbs in the rear light unit
⇒page 241, fig. 204
- Brake lights - Reversing lights - Rear fog light - Turn signal lights - parking lights
Licence plate light– Unscrew the glass
cover of the light
⇒fig. 205
.
– Take the faulty bulb out of the holder and insert a new one.– Replace the the glass cover of the light and press it down to the stop - ensure that
the glass cover is correctly installed.
– Screw the glass cover tight.
AA
A1A2A3A4A5
Fig. 205 Licence plate light
sgg.6.book Page 242 Thursday, September 24, 2009 2:32 PM