2009 SKODA YETI wipers

The brief instruction
13
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Switching lights on and offFurther information
⇒page 53, “Switching
lights on and off
”.
Turn signal and main beam lever Turn signal light right Turn signal light left Switching over between low beam and main beam lights Headlight flasherFurther information
⇒page 59, “The turn signal
  and main beam lever
”.
Windscreen wiper lever Intermittent switch, sensitivity setting rain sensor* Wipers off Intermittent wipe

Automatic light control*

Switching off all lights/daylight driving lights

Switching on side lights

Switching on the low beam and main beam

Fog lights*

Rear fog light
Fig. 7 Dash panel: Light switch
Fig. 8 Turn signal and main beam lever
AAABACAD
Fig. 9 Windscreen wiper lever
AAA0A1
sgg.6.book Page 13 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
63
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Windshield wiper and wash systemWindshield wiper You can operate the windscreen wipers and automatic wipe/wash using the windscreen wiper lever.The windscreen wiper lever
⇒fig. 57
has the following positions:
Finger-operated wiping– If you wish to wipe the windscreen only
briefly
, push the lever into the sprung
position . If you hold the lever in the lo
wer position for more than 1 second, the
wiper wipes faster.
Intermittent wiping– Position the lever up into position . – Set with the switch the desired brea
k between the individual wiper strokes.
Slow wipe– Position the lever up into position .Fast wipe– Position the lever up into position .
Automatic wipe/wash for windscreen– Pull the lever towards the steering wheel into sprung position , the wash system
sprays immediately, the windscreen wiper starts wiping a little later. The wash system and the windscreen wiper operate simultaneously at a speed of more than 120 km/h.
– Release the lever. The windscreen wash system stops and the wiper continues for
another 3 - 4 wiper strokes (depending on
the period of spraying of the wind-
screen). At a speed of more than 2 km/h, the wiper wipes once again* 5 seconds after the last wiper stroke in order to wipe the last drops from the windscreen. This function can be activated/deacti
vated by a specialist garage.
Rain sensor*– Move the lever into position . – You can set the sensitivity of the sensor individually with switch .Wiping the rear window pane– Push the lever away from the steering wheel into position - the widescreen
wiper will operate every 6 seconds.
Automatic wipe/wash for the rear window pane*– Press the lever from the steering wheel forward into the sprung position , the
wash system sprays immediately, the windscreen wiper starts wiping a little later. A s l o n g a s y o u h o l d t h e l e v e r i n t h i s p o s i t i o n, th e w i p e r o p e ra t e s a s w e l l a s t h e w a s h system.
– Letting go of the lever will cause the windscreen wash system to stop and the wiper
to continue for another 2 - 3 wiper strokes
(depending on the period of spraying of
the windscreen).
The lever will stay in position after releasing it
.
Switching windscreen wipers off– Move the lever back into
its home position .
After the windscreen wiper switches off each
time or the ignition switches off for the
third time, the position of the windscreen wiper changes, this counteracts an early fatigue of the wiper rubbers.
Fig. 57 Windscreen wiper lever
A4
A1
AA
A2A3
A5
A1
AA
A6
A7
A6
A0
sgg.6.book Page 63 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
64The windscreen wipers and the wash system only operate if the ignition is switched on and the bonnet is closed
9).
If the intermittent wipe is switched on, the intervals are also controlled depending on speed. The rain sensor* automatically regulates
the break between the individual wiper
strokes depending on the intensity of the rain. The rear window will be wiped again if the front window wipers are on when reverse gear is selected. The windscreen washer nozzles are heated* when the ignition is switched on.Top up with wash liquid
⇒page 214.
Winter position If the windscreen wipers are in rest positi
on, they cannot be folded out from the wind-
screen. For this reason we recommend adjusting the windscreen wipers in winter so that they can be folded out from the windscreen easily. You can set this rest position as follows:•
Switch on the windscreen wipers.
•
Switch off the ignition. The windscreen wipers remain in the position in which they
were when switching off the ignition. You can also use the service position
⇒page 65 as a winter position.
WARNING
•
Properly maintained wind
screen wiper blades are essential for clear visi-
bility and safe driving
⇒page 65.
•
Do not use the windscreen washer sy
stem at low temperatures, without
heating the windscreen beforehand.
Otherwise the window cleaner could
freeze on the windscreen and re
strict the view to the front.
•
The rain sensor only operates as a support. The driver is not released from
the responsibility to set the function of the windscreen wipers manually depending on the visibility conditions.
Caution
In frosty weather, please firs
t of all check whether the windscreen wiper blades are not
frozen to the windscreen before switching them on. Switching on windscreen wipers when the blades are frozen to the windscreen may result in damage both to the blades and the motor of the windscreen wipers!
Note
•
If the slower or the faster wiper setting is switched on
⇒page 63, fig. 57
and
the vehicle speed decreases to below 4 km/h, the lower wiper step is switched on automatically. At a speed increase of more
than 8 km/h the previous wiper setting is
established again.•
If there is an obstacle on the windscre
en, the wiper will try to push away the
obstacle. If the obstacle continues to block
the wiper, the wiper stops after 5 cycles, in
order to avoid a damage to the wiper. Re
move the obstacle and and switch on the
wiper again.Automatic rear window wiper*If the windshield wiper lever is in the posi
tion or , the rear window wiper carries
out a wiping process every 30 seconds or
10 seconds at a speed above 5 km/h.
When the rain sensor* is active (the lever
is in the position ) the function is only
active if the front window wipers continue
to operate (no break between each wiping
process). Activation/deactivation The function of the automatic rear window wiper is activated/deactivated in the infor- mation display* in the menu:„
Setup„
Lights & Vision (Lights & Vision)„
Rear wiper
Note
The function of the automatic rear window
wiper is only valid for vehicles which are
equipped with the information display*. The function is activated in the factory.
9)On vehicles which do not have
a contact switch for the bonnet, the windshield wiper and wash
system operates also when
the bonnet is opened.
A2
A3
A2
A3
A1
sgg.6.book Page 64 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
65
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Alternative park position of the rear window wiperEach time after switching off the engine for
the second time, the wi
per blade of the rear
window wiper is tilted when the park position
is activated. Thus, the life of the wiper
blade is prolonged.Activating– Switch on the ignition - position
⇒page 109.
– Push the operating level in the position
⇒page 63, fig. 57
five times in succes-
sion within 5 seconds.
– Switch off the ignition. After switching on
the ignition again, the alternative park
position of the rear window wiper is activated.
– For deactivating the alternative park position of the rear window wiper, proceed in
the same way.
Headlight cleaning system*The headlights are being cleaned after the windscreen has been sprayed for the first time and fifth time, the low beam or main beam are switched on and the windscreen wiper lever was held in the position
⇒page 63, fig. 57
for about 1 second.
The headlight washer nozzles are moved forward out of the bumper by the water pres- sure for cleaning the headlights. You should remove stubborn dirt (such as in
sect residues) from the headlight lenses at
regular intervals, for example when refuelling
. Please refer to the following guidelines
⇒ page 196, “The headlight lenses”. You should remove any snow from the fixtur
es of the washer nozzles and clear ice in
winter with a de-icing spray in order to
ensure proper operation of the cleaning
system.
Replacing wiper blades for the windscreen wipersOne cannot fold out the wiper arms in the re
st position from the windscreen. Before
replacing the wiper arms you must pu
t them into the service position.
Service position for changing wiper blades– Close the bonnet. – Switch the ignition on and then again off. – Then press the windscreen wiper lever in the position
⇒page 63, fig. 57
within
10 seconds - the wiper arms move into the service position.
Taking off the wiper blade– Fold windscreen wiper arm away from the windscreen. – Press the locking button, in order to unlock the wiper blade and pull off in the
direction of arrow
⇒fig. 58
.
Attaching a wiper blade– Push the wiper blade until it locks up to the stop. – Check whether the wiper blade is correctly attached. – Fold the windscreen wiper ar
m back onto the windscreen.
The wiper arms move back into the rest posi
tion - after switching on the ignition and
after changing the position of the window
wiper lever or when driving at a speed
greater than 6°km/h.
A2
A6
A5
Fig. 58 Wiper blade for the windscreen wiper
A4
sgg.6.book Page 65 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
66Wiper blades in proper
condition are essential to obtain
good visibility
. Wiper blades
should not be allowed to become dirtied by
dust, insect remains and preserving wax.
Juddering or smearing of the
wiper blades could then be
due to wax residues left on
the windscreen by vehicle washing in automa
tic vehicle wash systems. It is therefore
important to
degrease
the lips of the wi
per blades after every pass through an
auto-
matic vehicle wash system
.
WARNING
•
If the windscreen wipers are handled carelessly, there is a risk of damage to
the windscreen.•
You should clean the wiper blades regu
larly with a windscreen cleaner in
order to avoid any smears. Clean a wiper blad
e with a sponge or cloth if it is very
dirty, for example from insect residues.•
Replace the wiper blades once or twice a year for safety reasons. The wiper
blades are available from specialist garages.Replacing the wiper blade on the rear window wiperTaking off the wiper blade– Fold windscreen wiper arm
away from the windscreen.
– Press the locking button, in order to unl
ock the wiper blade and pull off in the
direction of arrow
⇒fig. 59
.
Attaching a wiper blade– Push the wiper blade until it locks up to the stop. – Check whether the wiper blade is correctly attached. – Fold the windscreen wiper ar
m back onto the windscreen.
The same remarks apply here as for
⇒page 65.
Rear-view mirrorManual dimming interior rear-view mirrorBasic setting– Pull the lever on the bottom edge of the mirror forward.Dimming mirror– Pull the lever on the bottom edge of the mirror back.Automatic dimming interior rear-view mirror*Switching on the automatic dimming– Press the button - the warning light lights up
⇒fig. 60
.
Fig. 59 Wiper blade for rear window
Fig. 60 Automatic dimming interior rear-view mirror
AB
AA
sgg.6.book Page 66 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
203
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Inspecting and replenishingEngine compartmentBonnet remote releaseBonnet remote release– Pull the unlocking lever below the
dash panel on the driver's side
⇒fig. 169
.
The bonnet jumps out of its lock as a result of the spring force. A locking lever appears at the same time in the radiator grille.Opening and closing the bonnetFig. 170 Radiator grille: Locking lever / se
curing the bonnet with the bonnet support
Opening the bonnet– Unlock the bonnet
⇒fig. 169
.
– Ensure that the arms of the windscreen wipers are correctly in place against the
windscreen
before opening
the bonnet otherwise damage could occur to the
paintwork.
– Pressing on the locking lever in direction of arrow
⇒fig. 170
will unlock the
bonnet.
– Grasp the front part of the bonnet under the chrome trim. – Take the bonnet support out of its holder in direction of arrow and secure the
opened bonnet by inserting the end of the support in the opening designed for it ⇒fig. 170
.
Closing the bonnet– Lift the bonnet slightly and unhook the bonnet support. Press the bonnet support
into the holder designed to hold it.
– Allow the bonnet to drop from a height
of about 20 cm into the lock - bonnet
do
not press down on it
!
– Check whether the bonnet is properly closed.
WARNING
•
Never open the bonnet if you see that steam or coolant is flowing out of the
engine compartment - risk of scalding!
Wait long enough until the steam or
coolant has stopped escaping.•
For safety reasons, the bonnet must always be properly closed when
driving. One should therefore check that
the lock has in fact engaged properly
after closing the bonnet.•
Stop your vehicle immediately while driving if you notice that the lock is not
properly engaged and close the bonnet
properly - risk of an accident!
Fig. 169 Bonnet release lever
A1
A2A3
sgg.6.book Page 203 Thursday, September 24, 2009 2:32 PM

Breakdown assistance
230
WARNING
•
The non-insulated parts of the terminal clamps must never make contact
with each other. Furthermore, the cable connected to the positive terminal of the battery must not come into contact with electrically conducting parts of the vehicle - risk of a short circuit!•
Do not affix the jump starting cables to the negative terminal of the
discharged battery. There is
the risk of detonating gas seeping out the battery
being ignited by the strong spark which
results from the engine being started.
•
Run the jump-start cables so that they cannot be caught by any rotating
parts in the engine compartment.•
Do not bend over the batteries - risk of caustic burns!
•
The vent screws of the battery
cells must be tightened firmly.
•
Keep any sources of ignition (naked
flame, smouldering
cigarettes etc.)
away from the battery - risk of an explosion!•
Never jump-start the batteries which have a too low electrolyte level - risk
of explosion and caustic burns!Tow-starting and towing vehicleGeneralPlease pay attention to the following instru
ctions if you are going to use a tow rope:
Driver of the towing vehicle– Do not drive off until
the tow rope is taught.
– Release the clutch particularly gently wh
en starting off or depress the accelerator
particularly gently if yo
ur vehicle is fitted wi
th an automatic gearbox.
Driver of the towed vehicle– Switch the ignition on so that the steer
ing wheel is not blocked and you can also
operate the turn signal lights, the headlight flasher, the windscreen wipers and windscreen washer system.
– Take the vehicle out of gear or move the selector lever into position
N if your
vehicle is fitted with an automatic gearbox.
– Note that the brake servo unit and power steering only operate if the engine is
running. You will require significantly greater physical force to depress the brake pedal and to steer the vehicle
if the engine is not running.
– Ensure that the tow rope is always kept taught. Tow rope or tow bar A tow
bar
is safest way of towing a vehicle and also minimizes any shocks. You can use
a tow
rope
only if a suitable tow bar is not available.
The tow rope must be elastic to protect the
vehicle. Thus one shou
ld only use plastic
fibre rope or a rope made out
of a similarly elastic material.
Only attach the tow rope to the
towing eyes
provided for this purpose
⇒page 231
and
⇒page 231.
Driving style Towing another vehicle requires a certain am
ount of practice. Both drivers should be
familiar with the particular points about to
wing a vehicle. Unskilled drivers should not
attempt to tow in another vehicle or to be towed in. One should be constantly vigilant not to
allow impermissibly high
towing forces or
jerky loadings. There is always a risk of excessive stresses and damage resulting at the points to which you attach the tow rope or
tow bar when you attempt to tow a vehicle
which is not standing on a paved road.
Caution
If the gearbox of your vehicle no longer
contains any oil because of a defect, your
vehicle must only be towed in with the driven wheels raised clear of the ground, or on a special vehicle transporter or trailer.
Note
•
Please comply with any national legal provisions particularly regarding the
switched on signal systems, when towi
ng in or tow-starting another vehicle.
•
The tow rope must not be twisted as it may in certain circumstances result in the
front towing eye being unscrewed out of your vehicle.
sgg.6.book Page 230 Thursday, September 24, 2009 2:32 PM