2009 CHERY TIGGO ECU

Downloaded from www.Manualslib.com manuals search engine Air Cleaner Housing
Removal & Installation
1. Disconnect the negative battery cable.
2. Disconnect the air flow sensor electrical connector.
3. Loosen the clamp between the air intake hose and the air cleaner.
4. Remove the retaining bolt (1), securing the aircleaner housing to its base.
(Tighten: Air cleaner housing retaining bolts to
10 N·m)
5. Remove the air cleaner housing.
6. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020240
LTSM020160
02
02–169Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Removal & Installation - Right Mount
NOTE :
The following special tools are required to perform the repair procedure:
•Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the engine right mount retaining bolts (2) and remove the engine right mount bracket bolts
(1).
(Tighten: Engine right mount bolts to 70 N·m)
4. Installation is in the reverse order of removal.
Removal & Installation - Front Mount
NOTE :
The following special tools are required to perform the
repair procedure:
• Engine Hoist
1. Disconnect the negative battery cable.
2. Support the engine with the engine hoist.
3. Remove the bolts (1) securing the front engine mount.
(Tighten: Engine front mount bolts to 60 N·m)
4. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020155
BESM080035
02–182Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 30. Remove the bolts (1) securing the front enginemount.
(Tighten: Engine front mount bolt to 60 N·m)
31. Remove the bolts (2) securing the rear engine mount and the bolts (1) securing the mount
bracket.
(Tighten: Engine rear mount bolt to 60 N·m)
32. Remove the bolts (2) securing the left transaxle mount and the bolts (1) securing the mount
bracket.
(Tighten: Left transaxle mount bolt to 70 N·m)
ON-VEHICLE SERVICE
BESM080035
LTSM020188
LTSM020156
02
02–187Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 33. Remove the bolts (2) securing the right enginemount and the bolts (1) securing the mount
bracket.
(Tighten: Engine right mount bolt to 70 N·m)
34. Remove the mount assembly.
35. Verify all components between the engine and vehicle are disconnected.
36. Hoist the engine from vehicle.
CAUTION:
Verify all electrical connectors are disconnected prior to engine/transaxle removal.
37. Separate engine and transaxle. (Tighten: M12×1.75 bolts to 70 ± 5 N·m)
(Tighten: M10×1.5 bolts to 50 ± 5 N·m)
38. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020155
02–188Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Exhaust Manifold
Removal & Installation
1. Remove the bolts attaching the exhaust manifold heat shield.(Tighten: Exhaust manifold heat shield bolts to 14 N·m)
2. Remove the exhaust manifold heat shield.
3. Remove the three bolts securing the exhaust manifold to the catalytic converter assembly. (Tighten: Exhaust manifold to catalytic converter bolts to 49 ± 5 N·m)
4. Disconnect the catalytic converter assembly from the manifold.
5. Remove the exhaust manifold nuts. (Tighten: Exhaust manifold nuts to 29 ± 3 N·m)
6. Remove the exhaust manifold from the cylinder head.
7. Remove and discard exhaust manifold gasket.
1 - Exhaust Manifold Heat Shield
2 - Engine Hanger
3 - Oxygen Sensor4 - Exhaust Manifold
5 - Exhaust Manifold Gasket
ON-VEHICLE SERVICE
LTSM020179
02–200Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2. Remove the accelerator cable retaining bolt from the intake manifold.(Tighten: Accelerator cable retaining bolt to 10 N·m)
3. Remove the PCV hose (1).
4. Disconnect the four fuel injector electrical connec- tors (1).
5. Loosen the clamp between the air intake hose and the air cleaner.
6. Loosen the clamp between the air intake hose and the throttle body and then remove the intake pipe.
7. Remove the fuel rail bracket bolts. (Tighten: Fuel rail bracket bolts to 11 N·m)
8. Remove the fuel rail with the fuel injectors and set aside.
9. Remove the fuel injector O-rings.
10. Remove the screws securing the vacuum valve bracket to the intake manifold.
11. Set aside the vacuum valve and pipe.
12. Disconnect the intake manifold electrical harness, and vacuum hose.
ON-VEHICLE SERVICE
LTSM030024
LTSM020173
02–202Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NOTE :
The following special tools are required to perform the repair procedure:
•MB-991603 - Balance Shaft Bearing Puller Limiter
• MD-998162 - Plug Spanner
• MD-998371 - Balance Shaft Bearing Puller
• MD-998372 - Balance Shaft Bearing Puller
• MD-998375 - Crankshaft Front Oil Seal Installer
• MD-998705 - Balance Shaft Bearing Installer
• MD-998727 - Oil Pan Remover
• MD-998783 - Plug Spanner Fixer
• MB-991828 - Oil Filter Wrench
• MB-991396 - Oil Filter Wrench
1. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
2. Remove the upper balance shaft timing belt (See Upper Balance Shaft Timing Belt Removal & Installation in Section 02 Engine).
3. Raise and support the vehicle.
4. Loosen the oil drain plug and drain the oil.
5. Remove the oil pan retaining bolts. (Tighten: Oil pan bolts to 18 N·m)
6. Using special tool MD-998727 (1), remove the oil pan.
NOTE: Insert the special tool between cylinder
block and the oil pan. Do not use a screwdriver or
chisel, otherwise the edge of oil pan may be dis-
torted and oil leaks will occur.
7. Remove the oil strainer retaining bolts. (Tighten: Oil strainer bolts to 19 N·m)
8. Remove the oil strainer.
9. Remove the oil strainer gasket.
10. Secure the lower balance shaft. Remove the plug from the cylinder block and then insert a holder (1)
(8 mm diameter) into the hole.
NOTE: If the holder can be inserted more than 60
mm, then the timing marks are aligned. If the
holder could not be inserted more than 20-25 mm,
the lower balance shaft pulley should be rotated
one revolution and the timing marks should be then
be aligned. Keep the holder installed until the
installation of the timing belt is complete.
ON-VEHICLE SERVICE
LTSM020134
LTSM020186
02
02–205Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NOTE :
The following special tools are required to perform the repair procedure:
•MD-991603 - Balance Shaft Bearing Puller Limiter
• MD-998162 - Plug Spanner
• MD-998371 - Balance Shaft Bearing Puller
• MD-998372 - Balance Shaft Bearing Puller
• MD-998375 - Crankshaft Front Oil Seal Installer
• MD-998705 - Balance Shaft Bearing Installer
• MD-998727 - Oil Pan Remover
• MD-998783 - Plug Spanner Fixer
• MD-991828 - Oil Filter Wrench
• MD-991396 - Oil Filter Wrench
1. Raise and support the vehicle.
2. Loosen the oil drain plug and drain the oil.
3. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
4. Remove the upper balance shaft timing belt (See Upper Balance Shaft Timing Belt Removal & Installation in Section 02 Engine).
5. Remove the oil pan retaining bolts. (Tighten: Oil pan bolts to 18 N·m)
6. Using special tool MD-998727 (1), remove the oil pan.
NOTE: Insert the special tool between cylinder
block and the oil pan. Do not use a screwdriver or
chisel, otherwise the edge of oil pan may be dis-
torted and oil leaks will occur.
7. Remove the oil strainer retaining bolts. (Tighten: Oil strainer bolts to 19 N·m)
8. Remove the oil strainer.
9. Remove the oil strainer gasket.
10. Secure the lower balance shaft. Remove the plug from the cylinder block and then insert a holder (1)
(8 mm diameter) into the hole.
NOTE: If the holder can be inserted more than 60
mm, then the timing marks are aligned. If the
holder could not be inserted more than 20-25 mm,
the lower balance shaft pulley should be rotated
one revolution and the timing marks should be then
be aligned. Keep the holder installed until the
installation of the timing belt is complete.
ON-VEHICLE SERVICE
LTSM020134
LTSM020186
02
02–209Chery Automobile Co., Ltd.