2008 NISSAN TEANA check engine

PRECAUTIONS
RSU-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
MA
B
RSU
N
O
P
PRECAUTION
PRECAUTIONS
Precautions for SuspensionINFOID:0000000003811137
CAUTION:
• When installing rubber bushings, the final tightening must be carried out under unladen conditions
with tires on ground. Oil might shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
- Unladen conditions mean that fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools
and mats are in designated positions.
 After servicing suspension parts, be sure to check wheel alignment.
 Self-lock nuts are not reusable. Always use new ones when installing. Since new self-lock nuts are
pre-oiled, tighten as they are.

RSU-6
< ON-VEHICLE MAINTENANCE >
WHEEL ALIGNMENT
WHEEL ALIGNMENT
InspectionINFOID:0000000003813442
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
Check the following:
 Tires for improper air pressure and wear
 Road wheels for runout: refer to WT-2, "
Inspection".
 Wheel bearing axial end play: refer to RAX-3, "
Inspection".
 Shock absorber operation
 Each mounting point of axle and suspension for looseness and deformation
 Each of lower link, upper link, rear suspension member, suspension arm and shock absorber for cracks,
deformation, and other damage
 Vehicle height (posture)
CAMBER
 Measure camber of both right and left wheels with a suitable alignment gauge.
 If camber is outside specified range, adjust with adjusting bolt in
lower. Refer to RSU-7, "
Adjustment".
TOE-IN
Measure toe-in by the following procedure.
WARNING:
 Always perform the following procedure on a flat surface.
 Make sure that no person is in front of vehicle before pushing it.
1. Bounce the front of vehicle up and down to stabilize the vehicle height (posture).
2. Push vehicle straight ahead about 5 m (16 ft).
3. Put matching mark (A) on base line of the tread (rear side) of
both tires at the same height of hub center. These are measur-
ing points.Standard
Camber: Refer to RSU-20, "
Wheel Alignment".
SRA096A
JPEIA0014ZZ

SEC-3
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P Diagnosis Procedure ...............................................
78
B260C STEERING LOCK UNIT .........................79
Description ..............................................................79
DTC Logic ...............................................................79
Diagnosis Procedure ...............................................79
B260D STEERING LOCK UNIT .........................80
Description ..............................................................80
DTC Logic ...............................................................80
Diagnosis Procedure ...............................................80
B260F ENGINE STATUS ...................................81
Description ..............................................................81
DTC Logic ...............................................................81
Diagnosis Procedure ...............................................81
B26E1 NO RECEPTION OF ENGINE STA-
TUS SIGNAL ......................................................
82
Description ..............................................................82
DTC Logic ...............................................................82
Diagnosis Procedure ...............................................82
B26E9 STEERING STATUS ..............................83
Description ..............................................................83
DTC Logic ...............................................................83
Diagnosis Procedure ...............................................83
B26EA KEY REGISTRATION ............................84
Description ..............................................................84
DTC Logic ...............................................................84
Diagnosis Procedure ...............................................84
B2612 STEERING STATUS ...............................85
Description ..............................................................85
DTC Logic ...............................................................85
Diagnosis Procedure ...............................................85
B2617 STARTER RELAY CIRCUIT ...................89
Description ..............................................................89
DTC Logic ...............................................................89
Diagnosis Procedure ...............................................89
B2619 BCM ........................................................91
Description ..............................................................91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
B261A PUSH-BUTTON IGNITION SWITCH .....92
Description ..............................................................92
DTC Logic ...............................................................92
Diagnosis Procedure ...............................................92
B261E VEHICLE TYPE ......................................95
Description ..............................................................95
DTC Logic ...............................................................95
Diagnosis Procedure ...............................................95
B2108 STEERING LOCK RELAY ......................96
Description ..............................................................96
DTC Logic ...............................................................96
Diagnosis Procedure ...............................................96
B2109 STEERING LOCK RELAY ....................97
Description ...............................................................97
DTC Logic ................................................................97
Diagnosis Procedure ...............................................97
B210A STEERING LOCK CONDITION
SWITCH .............................................................
98
Description ...............................................................98
DTC Logic ................................................................98
Diagnosis Procedure ...............................................98
B210B STARTER CONTROL RELAY ............102
Description .............................................................102
DTC Logic ..............................................................102
Diagnosis Procedure .............................................102
B210C STARTER CONTROL RELAY ............103
Description .............................................................103
DTC Logic ..............................................................103
Diagnosis Procedure .............................................103
B210D STARTER RELAY ..............................104
Description .............................................................104
DTC Logic ..............................................................104
Diagnosis Procedure .............................................104
B210E STARTER RELAY ...............................105
Description .............................................................105
DTC Logic ..............................................................105
Diagnosis Procedure .............................................105
B210F PNP/CLUTCH INTERLOCK SWITCH .107
Description .............................................................107
DTC Logic ..............................................................107
Diagnosis Procedure .............................................107
B2110 PNP/CLUTCH INTERLOCK SWITCH .109
Description .............................................................109
DTC Logic ..............................................................109
Diagnosis Procedure .............................................109
POWER SUPPLY AND GROUND CIRCUIT ..111
BCM .........................................................................111
BCM : Diagnosis Procedure ..................................111
IPDM E/R ..................................................................111
IPDM E/R : Diagnosis Procedure ..........................111
HOOD SWITCH ...............................................113
Description .............................................................113
Component Function Check ................................113
Diagnosis Procedure ............................................113
Component Inspection ...........................................114
SECURITY INDICATOR LAMP ......................115
Description .............................................................115
Component Function Check ................................115
Diagnosis Procedure .............................................115
Component Inspection ...........................................116
KEY WARNING LAMP ....................................117

SEC-4
Description .............................................................117
Component Function Check ................................117
Diagnosis Procedure .............................................117
HORN FUNCTION ...........................................118
Description .............................................................118
Component Function Check ................................118
Diagnosis Procedure ............................................118
HAZARD FUNCTION .......................................120
Description .............................................................120
Component Function Check ................................120
Diagnosis Procedure .............................................120
INTELLIGENT KEY SYSTEM/ENGINE
START FUNCTION ..........................................
121
Wiring Diagram - INTELLIGENT KEY SYSTEM/
ENGINE START FUNCTION - ..............................
121
NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS ................................................................
129
Wiring Diagram - NVIS - ........................................129
VEHICLE SECURITY SYSTEM .......................137
Wiring Diagram - VEHICLE SECURITY SYSTEM
- .............................................................................
137
ECU DIAGNOSIS .......................................144
BCM (BODY CONTROL MODULE) ................144
Reference Value ....................................................144
Wiring Diagram - BCM - ........................................167
Fail-safe .................................................................173
DTC Inspection Priority Chart .............................175
DTC Index .............................................................176
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ...............
178
Reference Value ....................................................178
Wiring Diagram - IPDM E/R - .................................186
Fail-safe .................................................................189
DTC Index .............................................................191
SYMPTOM DIAGNOSIS ............................192
SECURITY CONTROL SYSTEM .....................192
Symptom Table .....................................................192
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSIDE OF VEHICLE ...............
193
Description .............................................................193
Diagnosis Procedure .............................................193
STEERING DOES NOT LOCK ........................194
Description .............................................................194
Diagnosis Procedure .............................................194
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSERTED INTO KEY SLOT ...
195
Description ............................................................195
Diagnosis Procedure .............................................195
SECURITY INDICATOR LAMP DOES NOT
TURN ON OR FLASH ......................................
196
Description ............................................................196
Diagnosis Procedure .............................................196
VEHICLE SECURITY SYSTEM CAN NOT BE
SET ...................................................................
197
INTELLIGENT KEY .................................................197
INTELLIGENT KEY : Description ..........................197
INTELLIGENT KEY : Diagnosis Procedure ..........197
DOOR REQUEST SWITCH .....................................197
DOOR REQUEST SWITCH : Description .............197
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
197
VEHICLE SECURITY ALARM DOES NOT
ACTIVATE ........................................................
199
Description ............................................................199
Diagnosis Procedure .............................................199
VEHICLE SECURITY SYSTEM CAN NOT BE
CANCELED ......................................................
200
INTELLIGENT KEY .................................................200
INTELLIGENT KEY : Description ..........................200
INTELLIGENT KEY : Diagnosis Procedure ..........200
DOOR REQUEST SWITCH .....................................200
DOOR REQUEST SWITCH : Description .............200
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
200
KEY SLOT INDICATOR DOES NOT ILLUMI-
NATE ................................................................
201
Description ............................................................201
Diagnosis Procedure .............................................201
PRECAUTION ...........................................202
PRECAUTIONS ................................................202
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
202
Precaution for Procedure without Cowl Top Cover .202
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
202
ON-VEHICLE REPAIR ..............................204
KEY SLOT ........................................................204
Removal and Installation .......................................204
PUSH BUTTON IGNITION SWITCH ................205
Removal and Installation .......................................205

DIAGNOSIS SYSTEM (BCM)
SEC-23
< FUNCTION DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
SELF-DIAG RESULT
Refer to SEC-176, "DTCIndex".
DATA MONITOR
Monitor item Description
REMO CONT ID CONFIR It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SETAuto door lock time can be changed in this mode.
 MODE 1: 1 minute
 MODE 2: 5 minutes
 MODE 3: 30 seconds
 MODE 4: 2 minutes
LOCK/UNLOCK BY I-KEYDoor lock/unlock function by door request switch (driver side and passenger side) mode can be
changed to operate (WITH) or not operate (WITHOUT) in this mode.
ENGINE START BY I-KEYEngine start function mode can be changed to operate (WITH) or not operate (WITHOUT) in this
mode.
TRUNK/GLASS HATCH OPENBuzzer reminder function mode by trunk lid opener request switch can be changed to operate
(WITH) or not operate (WITHOUT) in this mode.
PANIC ALARM SETNOTE:
This item is displayed, but cannot be used.
PW DOWN SETNOTE:
This item is displayed, but cannot be used.
TRUNK OPEN DELAYTrunk button pressing on Intelligent Key button can be selected as per the following in this mode.
 MODE 1: Press and hold
 MODE 2: Press twice
 MODE 3: Press and hold, or press twice
LO-BATT OF KEY FOB WARNIntelligent Key low battery warning mode can be changed to operate (WITH) or not operate (WITH-
OUT) in this mode.
ANTI KEY LOCK IN FUNCTIKey reminder function mode can be changed to operate (WITH) or not operate (WITHOUT) in this
mode.
HAZARD ANSWER BACKHazard reminder function mode can be selected from the following in this mode.
 LOCK ONLY: Door lock operation only
 UNLOCK ONLY: Door unlock operation only
 LOCK/UNLOCK: Lock/unlock operation
 OFF: Non-operational
ANS BACK I-KEY LOCKBuzzer reminder function (lock operation) mode by door request switch (driver side and passenger
side) can be selected from the following is this mode.
 Horn chirp: Sound horn
 Buzzer: Sound Intelligent Key warning buzzer
 OFF: Non-operational
ANS BACK I-KEY UNLOCKBuzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) in this mode.
SHORT CRANKING OUTPUTStarter motor can operate during the times below.
70 msec
 100 msec
 200 msec
INSIDE ANT DIAGNOSIS This function allows inside key antenna self-diagnosis.
HORN WITH KEYLESS LOCKHorn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) in this mode.
Monitor Item Condition
REQ SW -DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR Indicates [ON/OFF] condition of trunk lid opener request switch.
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B Indicates [ON/OFF] condition of ignition relay 2.

DIAGNOSIS SYSTEM (BCM)
SEC-25
< FUNCTION DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)INFOID:0000000003814916
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Test item Description
BATTERY SAVERThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SETNOTE:
This item is displayed, but cannot be used.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated when “ON” on CONSULT-III screen is touched.
INSIDE BUZZERThis test is able to check warning chime in combination meter operation.
 Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
 Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
 P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.
INDICATORThis test is able to check warning lamp operation.
 “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
 “KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.
INT LAMPThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
LCDThis test is able to check meter display information
 Engine start information displays when “BP N” on CONSULT-III screen is touched.
 Engine start information displays when “BP I” on CONSULT-III screen is touched.
 Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
 Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
 P position warning displays when “SFT P” on CONSULT-III screen is touched.
 Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
 Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
 Take away warning displays when “OUTKEY” on CONSULT-III screen is touched.
 OFF position warning displays when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCHThis test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.
FLASHERThis test is able to check security hazard lamp operation.
The hazard lamps will be activated when “RH” or “LH”on CONSULT-III screen is touched.
HORNThis test is able to check horn operation.
The horn will be activated when “ON” on CONSULT-III screen is touched.
P RANGEThis test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMIThis test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATORThis test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
ACC INDICATORThis test is able to check ACC indicator in push-ignition switch operation.
ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON INDThis test is able to check ON indicator in push-ignition switch operation.
ON indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMIThis test is able to check key slot illumination operation.
Key slot illumination illuminates when “ON” on CONSULT-III screen is touched.
TRUNK/BACK DOORThis test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.

P1610 LOCK MODE
SEC-31
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
P1610 LOCK MODE
DescriptionINFOID:0000000003814927
When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
 Unregistered Intelligent Key is used.
 BCM or ECM is malfunctioning.
DTC LogicINFOID:0000000003814928
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-31, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003814929
1.CHECK ENGINE START FUNCTION
1. Perform the check for DTC except DTC P1610.
2. Use CONSULT-III to erase DTC after fixing.
3. Turn ignition switch OFF.
4. Turn ignition switch ON when registered Intelligent Key is inserted into key slot and wait for 5 seconds.
5. Turn the ignition switch OFF and wait 5 seconds.
6. Repeat steps 4 and 5 twice (total of 3 cycles).
7. Check that engine can start when registered Intelligent Key is inserted into key slot.
>> INSPECTION END
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
P1610 LOCK MODEWhen the starting operation is carried out
five or more times consecutively under the
following conditions.
 Unregistered Intelligent Key
 BCM or ECM is malfunctioning.—

SEC-32
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
P1611 ID DISCORD, IMMU-ECM
P1611 ID DISCORD, IMMU-ECM
DescriptionINFOID:0000000003814930
BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.
DTC LogicINFOID:0000000003814931
DTC DETECTION LOGIC
NOTE:
 If DTC B1611 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
 If DTC B1611 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-32, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003814932
1.PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Manual NATS-IVIS/
NVIS”.
Can the system be initialized and can the engine be started with reregistered Intelligent Key?
YES >> INSPECTION END
NO >> GO TO 2.
2.REPLACE BCM
1. Replace BCM. Refer to BCS-78, "
Removal and Installation".
2. Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Manual NATS-IVIS/NVIS”.
Can the system be initialized and can the engine be started with reregistered Intelligent Key?
YES >> INSPECTION END
NO >> GO TO 3.
3.REPLACE ECM
1. Replace ECM. Refer to EC-14, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Descrip-
tion".
2. Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Manual NATS-IVIS/NVIS”.
Can the system be initialized and can the engine be started with reregistered Intelligent Key?
YES >> INSPECTION END
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
P1611ID DISCORD, IMMU-
ECMThe ID verification result between BCM and ECM is
NG. The registration is necessary.BCM
ECM