2008 INFINITI FX35 installation

REAR WIPER AND WASHER SYSTEMWW-41
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
WW
N
O P
3. Lift the blade up and then set it down onto back door window glass surface to set the blade center to lowest heat wire immedi-
ately.
4. Tighten rear wiper arm nuts to specified torque.
5. Spray washer fluid. Turn on rear wiper switch ON to operate wiper motor, and then turn rear wiper switch OFF (auto stop).
6. Ensure that wiper blade stop within the following range.
7. Install rear wiper arm cap.
Removal and Installation of Rear Wiper BladeINFOID:0000000001328590
REMOVAL
1. Remove rear wiper arm. Refer to WW-40, "Removal and Instal-
lation of Rear Wiper Arm, Adjustment of Wiper Arms Stop Loca-
tion".
2. Turn rear wiper blade 90 degrees against rear wiper arm, and pull it out downward for removal.
CAUTION:
Replace rear wiper blade as rear wiper blade assembly.
INSTALLATION
Installation is the reverse order of removal. Rear wiper arm nut : 8.8 N·m (0.90 kg-m, 78 in-lb)
Lowest heat wire :
± 3.75 mm ( ± 0.148 in)
PKID0496E
SKIA6169E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-42
< SERVICE INFORMATION >
REAR WIPER AND WASHER SYSTEM
Removal and Installation of Rear Wiper Motor
INFOID:0000000001328591
REMOVAL
1. Remove rear wiper arm. Refer to WW-40, "Removal and Installation of Rear Wiper Arm, Adjustment of
Wiper Arms Stop Location".
2. Remove pivot cap, and remove nut from vehicle.
3. Remove back door finisher. Refer to EI-47, "
Component Parts Location".
4. Disconnect rear wiper motor connector.
5. Remove rear wiper motor mounting bolts and remove rear wiper motor from vehicle.
CAUTION:
Never remove cushion rubber.
INSTALLATION
1. Install rear wiper motor to the vehicle.
2. Connect rear wiper motor connector. Turn rear wiper switch ON to operate rear wiper motor, and then turn
rear wiper switch OFF (auto stop).
3. Install back door finisher. Refer to EI-47, "
Component Parts Location".
4. Install pivot cap, and nut.
5. Install rear wiper arm and rear wiper arm caps. Refer to WW-40, "
Removal and Installation of Rear Wiper
Arm, Adjustment of Wiper Arms Stop Location".
CAUTION:
Never drop the wiper motor or cause it to contact other parts.
1. Rear wiper motor 2. Rear wiper mounting bolts 3. Rear wiper blade
4. Rear wiper arm 5. Rear wiper arm cap 6. Rear wiper arm nut
7. Pivot cap 8. Nut 9. Washer
10. Cushion rubber
SKIB7578E
PKIB3588E
Rear wiper motor mounting bolts : 5.8 N·m (0.59 kg-m, 51 in-lb)
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

REAR WIPER AND WASHER SYSTEMWW-43
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
WW
N
O P
Washer Nozzle AdjustmentINFOID:0000000001328592
 Adjust spray positions as shown in the figure.
Unit: mm (in)
 Insert a needle or suitable tool into the nozzle hole and move it to adjust the spray position.
Washer Tube LayoutINFOID:0000000001328593
Removal and Installation of Washer NozzleINFOID:0000000001328594
REMOVAL
Spray position h (height) (width)φ
S
A, B 2.5 (0.098) 80 (3.15) 30 (1.18)
SKIA5088E
Adjustable range : ± 15 ° (In any direction)
SKIA5087E
PKIC9709E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-44
< SERVICE INFORMATION >
REAR WIPER AND WASHER SYSTEM
1. Remove high-mounted stop lamp. Refer to LT-114, "High-
Mounted Stop Lamp".
2. Remove screw and remove washer nozzle from high-mounted stop lamp.
INSTALLATION
Installation is the reverse order of removal. Adjust nozzle spray location. Refer to WW-43, "Washer Nozzle
Adjustment".
Check ValveINFOID:0000000001328595
Blow check valve. Confirm that the air ventilates. Also confirm that
inhalation is impossible.
CAUTION:
A check valve is provided in the w asher fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
Inspection of Front Wiper and Washer Switch CircuitINFOID:0000000001328596
Refer to LT-104, "Combination Switch Inspection".
Removal and Installation of Re ar Wiper and Washer SwitchINFOID:0000000001328597
Refer to WW-28, "Removal and Installation of Front Wiper and Washer Switch".
Removal and Installation of Washer TankINFOID:0000000001328598
Refer to WW-28, "Removal and Installation of Washer Tank".
Removal and Installation of Front and Rear Washer pumpINFOID:0000000001328599
Refer to WW-29, "Removal and Installation of Front and Rear Washer Pump".
PKIB6132E
SEL411H
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

POWER SOCKETWW-45
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
WW
N
O P
POWER SOCKET
Wiring Diagram - P/SCKT -INFOID:0000000001328600
Removal and Installation of Front Power Socket - 1INFOID:0000000001328601
REMOVAL
TKWM4490E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-46
< SERVICE INFORMATION >
POWER SOCKET
1. Remove A/T console finisher. Refer to IP-10, "Component Parts
Location".
2. Remove instrument clock finisher. Refer to IP-10, "
Component
Parts Location".
3. Disconnect power socket connector.
4. Remove inner socket from the ring while pressing the hook on the ring out from square hole.
5. Remove ring from ashtray while pressing pawls.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Power Socket - 2INFOID:0000000001328602
REMOVAL
1. Remove inner socket from the ring. While pressing the hook on
the ring out from square hole.
2. Remove ring from power socket finisher while pressing pawls.
3. Disconnect power socket connector.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear Power SocketINFOID:0000000001328603
REMOVAL
1. Remove console rear finisher. Refer to IP-16, "Disassembly and
Assembly".
2. Disconnect power socket connector.
3. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
4. Remove ring from power socket finisher while pressing pawls.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Luggage Room Power SocketINFOID:0000000001328604
REMOVAL
PKIC9710E
SKIA5096E
SKIA5094E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

POWER SOCKETWW-47
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
WW
N
O P
1. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
2. Remove ring from power socket finisher while pressing pawls.
3. Disconnect power socket connector.
INSTALLATION
Installation is the reverse order of removal.
SKIA5097E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-48
< SERVICE INFORMATION >
HORN
HORN
Wiring Diagram - HORN -INFOID:0000000001328605
Removal and InstallationINFOID:0000000001328606
REMOVAL
1. Remove front grille. Refer to EI-22, "Component Parts Location".
TKWM4378E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C