2008 GEELY FC light

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Circuitry--Power supply
1. ST startup system
2. HEAD MAIN light system
3. spare
4. ECU instrument travel
computer (Aldine)
5. horn
6. turn light, alarm light
7. charging system
8. air condition system
9. electric injection system
10. audio system, air condition,
instrument, room light, trunk
light, door light
11. AM2 startup system
12. spare safety
13. spare safety
14. spare safety
15. spare safety
16. electric chair (Aldine)
17. electric fan
18. ABS system
19. ABS system20. left distance headlight
21. right distantce headlight
22. left low beams
23. right low beams
 314 

Circuitry--Power supply
24. spare
25. OBD discharge test system
26. rear fog light
27. Anti-burglary
28. DOOR center control, light con-
trol system
29. Defrost load
30. spare
31. spare
32. eletric injection system, safety
airbag system, anti-burglary
system, instrument system
33. spare
34. spare
35. spare
36. front fog light
37. AMI ignition system
38. TAILposition light, number platelight
39. brake light
40. electric sunroof
41. instrument system, air condition
system, defrost system, Re-
verse Radar, rear light, turn light.
42. CIG air condition system, audio
system, electric rear view mirror,
cigarette lighter
43. washer
44. spare
45. wiper
46. spare
47. center control, light control
system, anti-burglary system,
ABS system
48. air condition system
49. rear defrost system
50. electric glass operator
 315 

Windshield/bodywork glass/wing mirror--Electric window control system
Avometer terminalsconditionsregular situations
16-earth(input +B signal)turn ignition switch from OFF to ON 0V → 10-14V
11-earthalways conduction
12-earthalways conduction
15-earth(input IG signal)turn ignition switch from OFF to ON 0V→10-14V
(4) Inspect other windows whether they can not actuate except window of driver seat room, when the
electric window switch locked.
2. Inspect automation function
(a) inspect basic function
(1) Turn the ignition switch to ON
(2) Inspect whether driver seat window automatic descends completely, when you press electric win-
dow main switch.
(3) Inspect whether driver seat window stop descending when driver seat window automatic descends
and press the main switch.
If the voltage and conduction do not accord with the regulations, the input side of electric window main
switch may have malfunction.
(b) Inspect the joint terminal voltage when connect the joint.
If the voltage does not accord with the regulations, electric window main switch may have malfunction.
(c) Inspect whether AUTO headlamp(LED) lights when connect the joint, turn the ignition switch from
OFF to ON.
 318 
Avometer terminalsconditionsregular situations
4-earth turn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.UP) Main switch from OFF to UP (manual operation)
9-earthturn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.DOWN)Main switch from OFF to DOWN (manual operation)
9-earthturn the ignition switch to ON, turn Off Driver
seat
window → driver seat Main switch to DOWN 0V→over9V→0V
(output P/W.DOWN)
(auto Operation)
→ windows open completely.
3. Inspect electric window main switch assembly
(a) Inspect operations
(1) Disassemble the joint of driver seat electric window main
switch and inspect the voltage and conduction among
terminals.

Windshield/bodywork glass/wing mirror--Rear ventilation window
Rear ventilation window
Change
Clues on: Please assemble by the sequence opposite with disassembling sequence. Assemble
directions could be got when necessary.
1. Disassemble the step trim board of left rear door [68010022] (referring to page 390)
2. Disassemble the step trim board of right rear door [68010024] (referring to page 390)
3. Disassemble left rear door frame sealed tape [68010059]
4. Disassemble right rear door frame sealed tape [68010060]
5. Disassemble rear seat cushion
6. Disassemble rear seat back assembly (fixed) [68010076] (referring to page 354)
7. Disassemble rear seat right back assembly (fixed) [68010079] (referring to page 352)
8. Disassemble rear seat left side back assembly (separate) [68010078](referring to page
352)
9. Disassemble left rear pillar interior trim board assembly [68010026] (referring to page
390)
10. Disassemble right rear pillar interior trim board assembly [68010027] (referring to page
390)
11. Disassemble high brake light assembly [68010008]
12. Disassemble rear platform front-below trim board [68010034]
13. Disassemble rear wind window sealed trim tape [68000104]
(a) Use blade to cut the trim tape as the drawing.
steel wire
 324 
Notes: Do not damage the bodywork by blade.
(b) Disassemble rudimental trim tape.
14. Disassemble rear ventilation window assembly
[68000103]
(a) Use a steel wire to drill through windows and bodywork.
(b) Tie something like wood block at both the end of steel wire.
Clues on: Stick adhesive tape on the bodywork at work
to prevent paintwork from scraping.
Notes: When separate window, do not damage
paintwork and interior and exterior trim board.
(c) Pull steel wire along front windscreen around, removal
agglutinant.
(d) Disassemble front windscreen.
Note: When cut front windscreen down, leave aggluti-
nant as much as possible on the bodywork.
15. Clean rear ventilation window assembly [68000103]
Use white gasoline to clean rear ventilation window around.
16. Assemble windscreen orientation plastic button
[68000064]
Assemble two orientation block on the rear windscreen as the

Panel/combination instrument--combination instrument
Panel / combination instrument
combination instrument
Trouble table
Lightening:
Phenomenon
All lights fail
Only one light failsPossible parts of trouble
1. combination instrument assembly
2. joint or harness
1. combination instrument assemblyReference pages
-
-
-
Indicator light:
Phenomenon
Trouble light fails
Charge light fails
Brake system light fails
ABS light fails
SRS lights fails
Door light fails
low fuel level light fails
low Oil pressure light failsPossible parts of trouble
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. airbag sensor assembly
3. combination instrument assembly
1. harness or joint
2. door control switch
3. combination instrument assembly
1. harness or joint
2. fuel level light switch
3. combination instrument assembly
1. combination instrument assembly
2. oil pressure light switch
3. harness or jointReference pages
-
-
-
-
-
-
-
-
335
-
-
335
-
-
-
-
-
-
-
335
335
-
335
335
 334 

Panel/combination instrument--combination instrument
Indicator light:
Phenomenon
Turning light fails
Distant light failsPossible parts of trouble
1. harness or joint
2. turn light and safety warning light system
3. combination instrument assembly
1. harness or joint
2. left combination switch
3. combination instrument assemblyReference pages
-
-
335
-
-
335
Instrument:
Phenomenon
Revolution counter, petrol guage and
engine water thermometer fail
petrol guage fails or works abnormallyPossible parts of trouble
1. harness or joint
2. (panel) safety fuse
3. combination instrument assembly
1. harness or joint
2. Fuel guage sensor
3. combination instrument assemblyReference pages
-
-
335
-
335
335
Vehicle inspection
1. inspect speed counter
(1) Use speedometer tester to inspect allowed error of speedometer and action of speedometer
Reference: Km/h
speed indicated by speedometer actual speed
20km/h17-23km/h
40km/h35-40km/h
60km/h55-60km/h
80km/h75-80km/h
100km/h95-100km/h
120km/h 114-120km/h
140km/h133-140km/h
160km/h152-160km/h
Notes: tyre wear or tyre pressure too high or too low will increase error.
(2) Inspect speedometer needle offset
Reference: below 0.5km/h
 335 

Panel/combination instrument--combination instrument
2. Inspect output signal of vehicle speed.
(1) When vehicle run at 10km/h, inspect voltage between ter-
minal10 and terminal A1 of combination instrument assembly.
Standards: the voltage pulsates repeatedly between
0V to 5V for thirteen times.
Notes: Inspect the ignition switch “on” connects the
joint
3. Inspect speed gauge
(1) Connect a test tachometer. then startup the engine.
Notes:
zTachometer terminals polarity connects oppositely will damage interior transistors and
LEDs.
zWhen move or disassemble tachometer. do not drop on the ground or knock the surface.
(2) Compare indicted value test tachometer and combination instrument tachometer.
Standard indicted value (rmp) permitted values (rpm)
700 630-770
1,000 (900-1,100)
2,000 (1,850-2,250)
3,000 2,850-3,150
4,000 (3,800-4,200)
5,000 4,750-5,250
6,000 (5,700-6,300)
7,000 6,650-7,350
DC 13.5V, 25°C
(1) Disassemble the joint of fuel meter
(2) Turn ignition switch to ON, inspect indictor position of fuel guage.
Indictor position: F
(3) Connect short terminal1 and terminal2 of wiring harness sides. Turn ignition switch to ON, inspect
indictor position of fuel guage.
Indictor position: F
5. Inspect low fuel level indictor 4. Inspect fuel gauge
The fuel gauge has the function of sensor detection (that is
failure treatment of oil level tachometer)that is when fuel gauge
indictor is at E position, if low oil level warning light doesn”t
light, first should judge whether there have open-loop trouble of
fuel sensor or wiring harness. When sensor fails, fuel indictor
should stop at current position. But if failing time is over 20
seconds, the indictor will return to E position quickly, the in-
strument will at wire break detection. If the normal situation of
detection panel is over 20 seconds, indicator will return to normal.
A1A20
 336