2008 GEELY FC light

Exterior/inner trim board--Light fender
Light fender
Change
1. Disassemble locker core and pedestal of trunk.
2. Disassemble number plate light defender [68000107]
Disassemble four screw caps, then disassemble the defender.
3. Assemble rear logo assembly [61000019]
(a) Use white gasoline to clean the assembling surface of logo.
(b) Use heating light to heat defender and logo.
(c) Assemble the logo.
Note:do not heat logo excessively
2 Fixing clamp
 386 

Exterior/inner trim board--Top left trim tape
Top left trim tape
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zChanging procedure for right side is same as left side.
1. Disassemble top left trim tape [68000128]
(a) Use protective adhesive tape to affix around the trimtape.
(b) Use disassembling tool for trim tape to release the front and
rear fixing clamp of trim tape, then disassemble top left trim
tape.
Note:
zDo not disassemble fixing clamp.
zIf fixing clamp is damaged when disassembling,
change it with new one.
2. Assemble top left trim tape [68000128]
Note: when only changing fixing clamp.
(a) Disassemble adhesive tape remaining on the surface of
body affixed trim tape, then use white gasoline to clean the
surface.
(b) Use heating light to heat the assembling surface of fixing
clamp and automobile body.
Automobile body: 40-60°C.
Trimtape: 20-30°C.
Note: do not heat the trim tape and body too much.
(c) Put the fixing clamp on the position shown in figure, then
press it into position with hand.
(d) After pressing the fixing clamp into position for over 30
minutes, then assemble top left trimtape.
Hint:
zSurface induration time: 30 minutes.
zComplete induration time: 24 hours.
 387 

Exterior/inner trim board--Inner trim board of top
Fixing
clamp
24. Disassemble right sun shade assembly [68010085]
(a) Liking that shown in figure, use screw driver to unclench the
trim cover of fixing pedestal, then pull down the trim cover.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Liking that shown in figure, use screw driver to release fixing
claw and disassemble sun shade.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(c) Use same method to disassemble the trim board at the
other side.
25. Disassemble left sun shade assembly [68010084]
26. Disassemble indoor front top light assembly
[67010005]
Use screw driver to disassemble front top light cover, and dis-
assemble fixing screw with cross wrench, then disconnect the
joint.
Hint: before using screw driver, its needled top should be
twisted by adhesive tape.
27. Disassemble indoor rear top light assembly
[67010006]
(a) Disassemble two screws and indoor light, then disconnect
the joint.
28. Disassemble passenger hand rail [68010088]
(a) Use screw driver to disassemble trim cover of handrail.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Disassemble two screws and passenger handrail.
 392 

Wiper and water injection Brake lightElectrical schematic diagram--Wiper and water injection Brake light 400 

Door control system Anti-stealing system Central control system Light systemElectrical schematic diagram--Door control system Anti-stealing system Central control system Light system 405 

Adjustment for headlight height Speaker cigar lighter Audio systemElectrical schematic diagram--Adjustment for headlight height Speaker cigar lighter Sound system 406