Brief introduction on Geely model “FC” Basic parametersTable 2 Types and parameters of main assemblyModel
TypeElectric injection system modelBore
StrokeDelivery capacityCompression ratioMax. power
Max. torque
Idling speedIgnition sequenceMin. fuel consumptionTypeMain gear box ratioTypes and parameters
JL4G184-cylinderin-line, four-stroke, water-cooling, double over-head
camshaft, 16-valve, CVVT multipoint injection gasoline engineUnited Automotive Electronic Systems Co., Ltd. M7.9.7 electric injection system5 gears synchronizer of constant mesh gearDry single, diaphragm spring, constant pressure
Rack-and-pinion steering gear with hydraulic powerDouble pipeline, vacuum boosterwith ABS +EBD anti-lock systemDisc brake
Disc brake
Strut-type front independent suspensionLongitudinal swinging arm and anti-twist beam compound rear suspensionBreakawayBalI cage and tripot type constant velocity universal jointLoaded all-metal body
Honeycomb cordierite carrier, noble metal catalyst
Swirl or swash plate compressorItem nameNumber
Engine1st gear
2nd gear
3rd gear
4th gear
5th gearReverse gearClutch type
Steering gear
Tire
Body structureSpecification
Air pressureRadial
tireTail gasAir
condi-
tioning
systemUnit
/ /
.
/ /
/
/ .
2
Transmission
Each gear ratio
Braking
system
Sus-
pension
Drive
axleType
Front brake
Rear brakeFront suspension type
Rear suspension typeRim
Type
Drive shaftCatalytic converterCompressor typeNominal refrigerating capacityRefrigerant
Exhaust - Exhaust pipe assemblyExhaustExhaust pipe assemblyRemoving, installing and disassembling, assembling1. Remove oxygen sensor.(a) Uncouple oxygen sensor joint.
(b) Remove oxygen sensor.2. Remove exhaust pipe guard [64000051].
3. Remove front exhaust pipe together with three-way catalytic converter assembly
[64000042].
4. Remove middle exhaust pipe together with middle silencing device assembly [64000043].
5. Remove rear exhaust pipe together with rear silencing device assembly [64000044].
6. Install front exhaust pipe together with three-way catalytic converter assembly [64000042].(a) Measure free length of compression spring with vernier caliper.
Free length: 43mm
Hint: if the free length does dot reach the standard value, it is necessary to replace compres-
sion spring.
(b) Gently knock silencing device inlet seal ring to exhaust manifold with hammer and wooden block until
the surfaces are parallel and level with each other.
Notes:Gently knock gasket toward positive direction.Do not repeat using the gasket that has been removed.Do not push the gasket in by means of tightening
bolt connection.
(c) Install exhaust pipe.
Torque: 43 N.m7. Install oxygen sensor.Torque: 44 N.m9. Install rear exhaust pipe together with rear guard
assembly [64000044].(a) Measure free length of compression spring with vernier
caliper.
Free length: 40mm
Hint: if the free length does dot reach the standard value, it is necessary to replace com-
pression spring.
(b) Install tail pipe to front pipe using a new gasket.
Torque: 43 N.m10. Install front exhaust pipe guard [64000051].
11. Check there is gas leakage with exhaust system.wooden
blockGaskett8. Install middle exhaust pipe together with middle si-
lencing device assembly [64000043].Couple front intake pipe of middle exhaust pipe together with
middle silencing device assembly with outlet pipe of front ex-
haust pipe together with three-way catalytic converter using a
new gasket.Torque: 43 N.mTail pipe sideGasket65
Parking front brake pull cable assembly
Change
Parking brake--Parking front bake pull cable assembly
156 1. Disassemble upper trim board on box.
2. Disassemble parking brake hole cover.
3. Disassemble central box.
4. Disassemble parking brake handle assembly.
5. Disassemble front bottom board bracket.
6. Disassemble front exhaust pipe with Three-Way
Catalytic Converter assembly.
(a) Disassemble the joint of oxygen sensor.
(b) Disassemble four bolts, compressed spring and front ex-
haust pipe with Three-Way Catalytic Converter assembly.
7. Disassemble heat insulation board of front exhaust
pipe.
Disassemble there screw caps and heat insulation board of
front exhaust pipe.
8. Disassemble parking front brake pull cable
assembly.
9. Assemble parking front brake pull cable assembly.
10. Assemble heat insulation board of front exhaust
pipe.
Assemble heat insulation board of front exhaust pipe with there
screw caps.
Torque: 5.4 N
⋅ ⋅⋅ ⋅
⋅m
11. Assemble front exhaust pipe with Three-Way Cata-
lytic Converter assembly.
(a) Assemble two new gaskets and front exhaust pipe with
Three-Way Catalytic Converter assembly with four com-
pressed springs and bolts.
Torque: 43
± ±± ±
± 3 N
⋅ ⋅⋅ ⋅
⋅m
(b) Connect the joint of oxygen sensor.
