2008 GEELY FC light

Panel/combination instrument--combination instrument
(1) Disassemble fuel meter joints or break wire, when indictor is at E, fuel indictor does not light.
(2) Jumper a 300-330
resistor from the corner of terminal1 and termianl2, turn ignition switch to ON,
indictor is at E line, the indictor light lights.
6. Inspect generator water thermometer .
(1) Disassemble joint of generator water thermometer
(2) Turn ignition switch to ON, inspect indictor position of gen-
erator water thermometer.
Indictor position: COOL
(3) Earth 2 terminal of the wiring harness side joint to inspect
indictor position of generator water thermometer.
Indictor position: HOT
1 2 3
7. Inspect untied indictor light of driver seat belt.
(1) Turn ignition switch to ON, Inspect untied indictor light of driver seat belt lights.
(2) Tie the seat belt, inspect untied indictor light seat belt lights off.
(3) Disassemble the joint of safe belt button switch, earth the terminals of wiring harness
(4) Turn ignition switch to ON, inspect untied indictor light seat belt lights on.
8. Inspect low oil pressure indictor
(1) Disassemble the joint of oil pressure switch.
(2) Turn ignition switch to ON.
(3) Earth terminals of wiring harness sides, inspect low oil pressure indictor.
Low oil pressure indictor: light
9. Inspect oil pressure switch
(1) disassemble joints of oil pressure switch,
(2) Inspect the conduction of oil pressure switch terminals and earth.
Generator extinguishes: conduction
Generator works: not conduction
10. Inspect light warning buzzer
(a) Inspect the function of light warning buzzer
Clues on: light warning buzzer works together, only key
reminding buzzer works.
(1) Front combination light switch switches to ON, extract the
key, open driver seat door, inspect light warning buzzer.
Audio buzzer: Audio for 10 seconds in the night to cut
lamp power, in the day cut the lamp instantly.
(2) When buzzer works, do any one of the followings, inspect whether buzzer stop buzzing.
z zz z
zTurn front combination switch to OFF.
z zz z
zClose driver seat door.
z zz z
zInsert the key.
Buzzer Light switch
Key warning
switch
Pull out the key
Open driver door
 337 

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Panel/combination instrument-combination instrument
13. Check the switch of indicating light of brake liquid level.
(1) Disassemble the cover and filter screen of liquid storage tank of brake main pump.
(2) Disassemble the joint.
(3) Check the conduction between switch side joints.
Float (switch is OFF): not conduction
(4) Use siphon and other tools to absorb brake liquid in storage tank.
(5) Check the conduction between switch side joint terminals.
Sink (switch is ON): conduction
(6) Pour brake liquid into storage tank.
Inspection
1. Check the switch of indicating light of brake liquid level.
Check the conduction between switch side joint terminals.
Float ((switch is OFF): not conduction
Sink (switch is ON): conduction
2. Check parking brake switch.
Check the conduction between switch side joint terminals.
When switch pin is released: conduction
When switch pin is pressed: not conduction
 339 

Panel/combination instrument--panel
(b) Assemble CD machine assembly and panel central ventila-
tion hole assembly.
36. Assemble helix cable assembly (referring to page
261)
37. Assemble steering wheel assembly [67010001]
(referring to page 194)
38. Check the central position of steering wheel.
39. Check the safety airbag assembly at the side of
driver [67010011] (referring to page 249)
40. Assemble the safety airbag assembly at the side of
driver [67010011]
41. Check the warning light of SRS airbag
Fixing
clamp
4 Fixing
clamp
 346 

Anti-stealing and door lock--Electric door lock control system
Anti-stealing and door lock
Electric door lock control system
Position of parts (only for reference)
Inspection on automobile
1. Basic inspection for electric door locker.
(a) Press middle control switch to locker closing side, and check the all doors should be locked; then
press middle control switch to locker opening side, and check all doors should be opened.
(b) Insert key in door locker and turn it anticlockwise, and check all doors should be locked; then turn the
key clockwise, and check all doors should be opened.
(c) Check the keeping protection function of the key.
Note: When checking the keeping protection function of the key, it is necessary to open elec-
tric window at the side of driver to prevent its function from losing and lock the key in
automobile.
(1) Insert key in ignition switch.
(2) Open the door, and press middle control switch on the door at the side of driver to locker closing
side, at this time, door locker could not close.
(3) Open the door, and press locker button on the door at the side of driver to locker closing side, at
this time, door locker could not close.
(4) After pressing locker button upwards for over two seconds, and locking driver door; when driver
door is closed and key is not used to lock, check whether all doors could open automatically.
 355 
Door control switch of electric
window main switch assembly
(Used for handle operation)
Door control switch of left front
door locker assembly
(Used for key operation)
Door control light switch
Left rear door locker
assembly
Right front door
locker assembly
Right rear door
locker assembly

Anti-stealing and door lock--Electric door lock control system
 357 
Power supply (+) Power supply (+)
Power supply
(+)
1G2 in Power supply
(+)
1G2 out Power supply (-)
Power supply (+) Power supply (+) Power supply (+) Power supply (+)
Power supply
(+)Power supply
(+)Power supply
(-) Power supply
(+)
Power supply (+)
Power supply (+)
Grounding wire
Sunroof
Rain wiperBrake light Anti-steal
Power supply
(+)
InstrumentRear fog light

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof