2008 GEELY FC light

Safety airbag assemble at the side of passenger
1. Note (referring to chapter 1).
2. Use the flash or malfunction diagnostic tool to test the malfunction (referring to chapter
1 and 3).
3. Disconnect the connection of cathode of battery, and do not operate in 60 seconds after
disconnecting.
4. Disassemble the glove box.
5. Disassemble the joint of safety airbag at the side of passenger, and do not damage
airbag wiring harness carefully.
6. Disassemble the safety airbag assembly at the side of passenger.
a. Disassemble three connecting bolts from the bracket of safety airbag assembly at the side of passenger.
b. Take down the safety airbag assembly from panel.
7. Check the safety airbag assembly at the side of passenger (referring to chapter 2).
8. Assemble airbag assembly.
a. Check whether the connection between safety airbag module and airbag short wiring harness is firm.
b. Firstly, insert the module in assembling position from the upside of panel, secondly, align the assem-
bling hole of small bracket on module with the assembling hole on framework of panel, at the same
time, the module cover and panel clearance should be even, and the barb on module should be con-
nected to its position.
9. After assembling, use malfunction diagnostic tool or malfunction indicating light to
check and confirm the malfunction has been removed.
(3) Make three fixed claws mesh steering column.
When changing with new helix cable, it is necessary to disassemble yellow clamp before assembling.
(4) Insert the plug of airbag wiring harness in the plug of helix cable and make this connection firm.
Align the
mark Supplemental restraint system--Disassemble and assemble
 263 
(4) After assembling, use malfunction diagnostic tool or malfunction indicating light to check
and confirm the malfunction has been removed. (5) Connect the lower cover of combination switch.
(6) Connect the upper cover of combination switch with the
lower cover with special bolts firmly.
13. Set the helix cable at middle position
a. Check whether ignition switch locates OFF state.
b. Check whether the cathode end of battery has been
disassembled.
Note: do not operate in 60 seconds after disassembling
cathode end.
c. Turn helix cable anticlockwise with hand until it could not
be turned.
d. Then turn the helix cable clockwise for 2.5 circles to align
the mark.
14. Assemble steering wheel
(1) Inspection before assembling:
z Steering wheel
z Connecting wiring harness
z Safety airbag assembly at the side of driver
(2) Tighten the assembling screws at both sides.
(3) Connection of battery terminal “-”.

Rear safety belt
Subassembly
Safety belt--Rear safety belt
1. Inner trim board assembly of left rear column
[68010026]
2. Inner trim board assembly of right rear column
[68010027]
3. Backrest assembly of rear row seat [68010076]
4. Step bolt M8*20 of hexagon flange face
[68000203]
5. Cushion assembly of rear row seat [68010074]6. Rear platform with sun blind assembly
[68010032]
7. Plastic clamp of column trim board [68000089]
8. Rear safety belt crimper assembly [68010048]
9. Middle waistband of rear row safety belt with
locker assembly[68010043]
10. High mount brake light assembly [67010008]
N.
m : Regulated torque
54
982 6 10
7 1
3
8
41
41
41
41
 275 

Safety belt--Rear safety belt
.
 : Regulated torque
1
13
12
2 3
5
8
78
56
4
10
11
9
1. Inner trim board assembly of left rear column
[68010026]
2. Inner trim board assembly of right rear column
[68010027]
3. Left backrest assembly of rear row seat
[68010078]
4. Right backrest assembly of rear row seat
[68010079]
5. Combination part of Hexagon head bolt and flat
washer M6*14 [Q1400614]
6. Backrest assembly of rear row seat [68010076]7. Step bolt of hexagon flange face [68000203]
8. Combination part of hexagon bolt with flat big
washer M10*1.25*22 [Q1401022]
9. Cushion assembly of rear row seat [68010074]
10. Rear safety belt crimper assembly [68010048]
11. Middle waistband of rear row safety belt with
locker assembly [68010043]
12. Rear shelf with sun shade assembly
[68010032]
13. High mount brake light [68010008]
41
41
41
41
41
 276 

Safety belt--Rear safety belt
Change
Hint:
zWhen assembling, please work by the sequence that is reverse with disassembling sequence,
if necessary, assembling instruction could be got.
zChanging procedure for left side and right side is same.
zRefer to subassembly drawing of front safety belt on page 275.
1. Disassemble cushion assembly of rear row seat.
2. Disassemble Right backrest assembly of rear row seat [68010079]
3. Disassemble left backrest assembly of rear row seat [68010078]
4. Disassemble cushion assembly of rear row seat [68010074]
5. Disassemble backrest assembly of rear row seat [68010076]
6. Disassemble high mount brake light assembly [68010008]
7. Disassemble inner trim board assembly of right rear column [68010027]
8. Disassemble inner trim board assembly of left rear column [68010026]
9. Disassemble rear platform with sun blind assembly [68010032]
(a) Use special disassembling tool to disassemble three fixed clamps.
(b) Pull out safety belt from the clearance, then disassemble rear platform with sun blind assembly.
10. Disassemble rear safety belt crimper assembly [68010048]
(a) Disassemble the bolts and safety belt clamps.
(b) Disassemble the bolts and rear safety belt crimper assembly.
11. Disassemble middle waistband of rear row safety belt with locker assembly. [68010043]
(a) Disassemble the bolts and middle waistband of rear row safety belt with locker assembly.
 277 

Light--Light SystemThe phenomena table1. front combination lights and tail lightPhenomena
Only one front combination light
lights
Low beam headlights do not light
(all)
distance lights do not light (all)
Distance light do not light (one
side)
Flare does not light
Front combination lights are too
dark
Only one rear combination light
lights
Rear combination lights do not light
(front combination lights are normal)
Rear combination lights do not light
(front combination lights are abnormal)Reference pages
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-LightLight SystemNotes1. Notes for changing the front combination bulb(a) When the surface of halogen bulbs (the bulb of front assembled headlamp and front fog light) touches
oil, their working life will be shorten. When it lights, it becomes hot.
(b) Because of pressured gas in halogen bulbs (the bulb of front assembled headlamp and front fog
light), the bulb may explode and pieces of broken glass disperse around. So deal with it carefully.
(c) If the time after disassembling the bulb from lamp carrier is too long, the mirror may be polluted by
dirties or hydrosphere. You should prepare a new bulb,then replace it.
(d) Replace it with the lamp of same wattage.
(e) Assemble the changing bulb on the lamp carrier firmly, or it may bring mirror mirage or water intrusion.
(f) Do not touch the black of the top of glass, or it may shorten its working life.Possible part
1.bulb
2.fuse
3.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.bulb
2.wiring harness
1.left combination switch
2.flare
3.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
3.left combination switch
4.wiring harness
1.fuse
2.relay 279 

Light--Light System 280  2. Fog light System
3. Turning and emergency warning light systemEmergency warning light and turn
light does not light
Emergency warning light does
not light (turning light is normal)
Turn light does not light
(Emergency warning light is normalSide turning light does not light
(warning light is normal)
One side of turning light does not
light
One side of turning light does not
light
Only one bulb does not light1. (meter) fuse
2. (turn) fuse
3. ignition switch
4. flasher assembly
5. wiring harness
1. Emergency warning light switch
2. wiring harness
1. turn light switch
2. wiring harness
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
1. bulb
2. wiring harnessThe light control switch switches on,
the front fog lights do not light (front
combination lights are normal)Lamp switch turn to “HEAD”. front fog
lights do not light (front combination light
do not light)Only one front fog light do not light
Rear fog lights do not light (front
combination lights are normal)
(front fog lights are normal)
Rear fog lights do not light (front fog
lights do not light)1.(front fog light)fuse
2.fog light relay
3.fog light switch
4.wiring harness
1.other parts
2.wiring harness
1.bulb
2.wiring harness
1.fuse
2.rear fog light switch
3.wiring harness
4.bulb
1.other parts
2.wiring harness
3.bulb
4.front fog light switch
5.rear fog light switchphenomena
Possible part
Reference pagesphenomena
Possible partsReference pages

Light--Light System
All lights do not light
When driver cap side door opens,
the light does not light
When right front door opens, the
light does not light
When right rear door opens, the
light does not light
When left rear door opens, the light
does not light
Only one light can light
After all doors are closed, illuminat-
ing lamp will not flame out gradually.
After all doors closed, the head lamp
does not light in 15 seconds, when
turn ignition switch to ACC or ON.
Driver side light or passenger cap
side light do not light
When Driver side door opens,
driver side light does not light
When Passenger side door opens,
passenger side light does not light1. (room light) fuse
1. driver cap side door control switch
2. wiring harness
3. bulb
1. right front door control switch
2. wiring harness
3. bulb
1. right rear door control switch
2. wiring harness
3. bulb
1. left rear door control switch
2. wiring harness
3. bulb
1. bulb
1. Door-control switch
2. Wire harness
1. ignition switch
2. fuse
3. light relay
4. wiring harness
1. (door) fuse
2. (meter) fuse
3. light relay
4. driver side door control switch
5. bulb
6. wiring harness
1. driver side door control switch
2. wiring harness
3. bulb
1. passenger side door control switch
2. wiring harness
3. bulb
4. Room lights system
Inspect the car
1. inspect turning flasher wiring
(a) Disassemble joint from turning flasher and inspect wiring
harness side joint as following table.
phenomena
Possible partsReference pages
 281 

(b) Inspect function of rear fog light.
(1) Turn the ignition switch to ON.
(2) Inspect rear fog light’s situation when every switch works, just as following table.
Light--Light System
(b) Connect joint to directional switch and inspect from wiring harness’s side joint as following table:
Avometer terminals
2-earth
2-earth
3-earth
3-earth
5-earth
6-earth
8-earthcondition
warning light switch OFF → ON
turn light switch (right) OFF → ON
warning light switch OFF → ON
turn light (left) switch OFF → ON
turn light(left) switch OFF → ON
turn light(right) switch OFF → ON
warning light switch OFF → ONregular situation
0V → 0 ⇔ 9Vevery min 60 to 120 times
0V → 0 ⇔ every min 60 to 120 times
0V → 0 ⇔ 9Vevery min 60 to 120 times
0V → 0 ⇔ 9Vevery min 60 to 120 times
over 9V → 0V
over 9V → 0V
over 9V → 0V
2. Inspect rear fog light switch
(a) inspect rear fog light wiring
(1) Disassemble the joint from switch sides and inspect the
joint from wiring harness as following table.
Avometer terminals
1-earth
2-earth
3-earth
5-earth
6-earth
7-earthcondition
normal
light control switch OFF → ON
normal
light control switch OFF → ON
front fog light switch OFF → ON
normalregular situation
conduct
ion
0V → 10-14V
10-14V
not conduct
ion → conduction
not conduction→ conduction
conduction
Situation
Light switch OFF → ON, front fog light switch OFF
Light switch OFF → ON, front fog light switch ON, rear fog light switch ONrear fog light working situations
rear fog light does not light
rear fog light lights
3. Inspect lighting system function
Clues on: key aperture lamp and room light.
Avometer terminals
7-earth
1-earth
1-earth
4-earthcondition
normal
turn light switch ON
turn light switch ON
normalregular situations
conduct
ion
battery voltage
no voltage
battery voltage
Wiring
harness side
 282