2008 GEELY FC water pump

Brief introduction on Geely model “FC”
Basic parameters...................................................
1
Maintenance period
Regular maintenance items...................................
4
Table on maintenance period at normal conditions5
Table on maintenance period at severe conditions..
7
Engine control system
EFI system.............................................................
8
On-vehicle inspection........................................
8
Inspection..........................................................
9
Throttle body assembly........................................
13Removing, installing and disassembling, assembling...13
Fuel
Fuel system..........................................................
14
Precautions......................................................
14
On-vehicle inspection......................................
16
Inspection........................................................
17
Injection nozzle assembly....................................
18
Replacement...................................................
18
Fuel pump assembly...........................................
20Removing, installing and disassembling, assembling....20
Fuel tank assembly.............................................
21Removing, installing and disassembling, assembling.....21
Exhaust gas control
Exhaust gas control system...............................
23
On-vehicle inspection......................................
23
Inspection........................................................
25
Engine mechanism
Engine assembly..................................................
26Inspection........................................................
26
Drive belt..............................................................
29
Replacement...................................................
29
Valve clearance....................................................
30
Adjustment......................................................
30
Engine assembly.................................................
36
Replacement...................................................
36
Timing chain assembly.......................................
45
Replacement...................................................
45
Camshaft.............................................................
52
Replacement...................................................
52
Crankshaft front oil seal assembly.....................
60
Replacement...................................................
60
Crankshaft rear oil seal assembly......................
62
Replacement...................................................
62
Cylinder cover gasket components.....................
63
Replacement...................................................
63
Exhaust
Exhaust pipe assembly........................................
65Removing, installing and disassembling, assembling.....65
Cooling
Cooling system....................................................
66
On-vehicle inspection......................................
66
Inspection........................................................
66
Cooling fan system..............................................
68
On-vehicle inspection......................................
68
Inspection........................................................
68
Water pump assembly........................................
69
Replacement...................................................
69
Temperature regulator components...................
71
Replacement...................................................
71
Radiator with electronic fan assembly................
72Contents

34. Remove power steering pump assembly.
35. Remove sub frame together with side member.(a) Remove front engine mounting assembly and rear en-
gine mounting assembly from engine assembly.
(b) Remove sub frame assembly.36. Remove starter mounting components
[4G18-3708100].
37. Remove transmission assembly.(a) Fix crankshaft with special tool, ant then remove 6 bolts.
(b) Remove transmission assembly.38. Remove clutch assembly [4G18-1601000]
and flywheel components [4G18-1005120J].(a) Fix crankshaft with special tool, ant remove clutch
assembly at first.
(b) Then remove flywheel components.39. Remove throttlesupporting plate [4G18-1008202].
40. Remove intake manifold assembly [4G18-
1008200].(f) As shown in the diagram, install front and rear hooks of
engine.
Torque: Hint: install engine hooks to front and rear sides of
engine.
(g) Lift engine assembly with chain pulley block and en-
gine lifting device.Engine mechanism - Engine assemblySpecial tool39 41. Remove exhaust manifold upper heat shield components [4G18-1008120].
42. Remove exhaust manifold assembly [4G18-1008100].
43. Remove fuel rail injector assembly [4G18-1112100].
44. Remove ignition coil installation components.
45. Remove oil level gauge tube components [4G18-1002140].
46. Remove temperature regulator assembly [4G18-1306100].
47. Disassemble warm air water outlet pipe components [4G18-1300100].
48. Remove oil pressure alerter [4G18-3757100].Remove oil pressure alerter with SST.49. Remove the hoses on all hose joint of engine.Remove clips and hose.50. Remove drive belt tensioner device.
51. Remove phase sensor [4G18-3600030].Engine hook
FrontRear

Engine mechanism - Timing chain assembly14. Remove drive belt tensioner device.Hint: operate the jack up and down to remove bolts.15. Remove water pump components [4G18-1307110].(a) Remove 6 bolts and water pump components.16. Remove engine stabilizer bracket on engine cross
member.
17. Remove compressor.
18. Remove speed sensor.
19. Remove chain tensioner components
[4G18-1006160].Note: do not turn crankshaft before installing chain
tensioner components.20. Remove timing chain hood components
[4G18-1006140].(a) Remove 11 bolts and nuts.
(b) Remove studs with star wrench.
(c) Pry open timing chain hood from timing chain hood pro-
trusion part between cylinder head and body with screw-
driver and remove it.
Note: be careful not to damage timing chain
hood, the contact surface of cylinder head and
body.21. Remove crankshaft front oil seal assembly
[4G18-1006150].Remove oil seal with screwdriver.22. Remove speed sensor signal panel
[4G18-3600011A].
23. Remove chain tension rail components
[4G18-1006120].
24. Remove chain guide rail components
[4G18-1006130].
25. Remove timing chain [4G18-1006110].Remove it with 2 screwdrivers.
Notes:Place a piece of cloth to protect engine.In the state of timing chain separating from timing
sprocket and turning camshaft, turn crankshaft 1/4
circle to avoid valve contacting with piston.26. Install timing chain.(a) Turn crankshaft to cylinder 1 compression top dead
center position.
(1) Turn camshaft from hexagon head part of
camshaft, and align dot marks on camshaft timing
sprocket.46

Engine mechanism - Timing chain assembly34. Install speed sensor.Torque: 35. Install engine fixing bracketTorque: 36. Install water pump mounting components
[4G18-1307100].(a) Install new o-ring on water pump.
(b) Install water pump with 6 bolts.
Torque: bolt A: m37. Install drive belt tensioner device.Torque: nut: Bolt: m38. Install right engine mounting assembly.Torque: 39. Install cylinder head cover components.(a) Install gasket to cylinder head cover.
(b) Eliminate all old seal materials.
(c) Coat sealant on 2 positions shown in the diagram.
Sealant: silicon rubber flange sealant 1596
(Kesaixin 1596).
Notes:Eliminate all grease on contact surface.After coating sealant, finish installation of cylinder
head cover within 3 minutes.After installing, do not refill engine oil within 2
minutes.
(d) Install cylinder head cover and cable bracket with 9 bolts,
2 seal washers and 2 nuts.
Torque: nut: Bolt: m40. Install ignition coil mounting components.Torque: 50

Cooling - Cooling syste2. Check engine coolant level in reservoir.Engine coolant level should be between “Low” and “Full” mark line.
Hint: if the level is too low, check there is leakage and refill coolant to “Full” mark line.3. Check engine coolant quality.(a) Remove radiator cap.
Warning: when the temperature of engine and radiator is high, do not remove radiator cap to
avoid being scalded, because coolant and steam will spurt under high pressure.
(b) Check there is too much rust deposit around radiator cap or at outlet and check there is flake; there
should not be oil in the coolant.
Hint: if coolant is too dirty, it is required to replace coolant.
(c) Install back radiator cap.Inspection1. Temperature regulatorHint: the figure on temperature regulator is the
opening temperature of valve.CoolingCooling systemOn-vehicle inspection1. Check there is leakage with cooling system.Warning: when the temperature of engine and radiator is
high, do not remove radiator cap to avoid be-
ing scalded, because coolant and steam will
spurt under high pressure.
(a) Refill coolant to radiator, and install radiator cap tester.
(b) Preheat engine.
(c) Pump tester to make pressure go up to 118KPa, and check
the pressure falls.
Hint: if the pressure falls, check there is leakage with
hose, radiator or water pump, and check heater,
cylinder body and cylinder head if no external leak-
age is found.66

Cooling - Cooling systeTemperatureDegree of valve opening(a) Immerse temperature regulator into water and heat
gradually.
(b) Check opening temperature of valve.
Opening temperature of valve: 8084Hint: if opening temperature of valve is not within
specified range, it is required to replace tempera-
ture regulator.
(c) Check opening of valve.
Opening of valve:2. Radiator cap assemblyNotes:If radiator is dirty, wash it with clean water.Before using radiator cap tester, dampen relief valve
and pressure valve with coolant or water.
(a) Use radiator cap tester to slowly pump radiator cap
tester, and check the air is released by vacuum valve.
Pumping speed: 1 time /(3 seconds or more)
Note: pump radiator tester with constant speed.
Hints:Pumping speed: 1 time /(3 seconds or more)If air could not be released by vacuum valve,
please replace radiator cap.
(b) Pump tester and check opening pressure of relief valve.
Standard opening pressure: 74-108KPa
Min. opening pressure: 59KPa
Note: pumping speed means that the speed could be increased after the first time pumping
speed (to close vacuum valve).
Hints:Pumping speed: 1 time within 1 secondMax. reading of tester is opening pressure.If opening pressure is less than min. value, please replace radiator cap. Hint: if degree of valve opening is not within speci-
fied range, it is required to replace tempera-
ture regulator.
(a) When temperature regulator is at low temperature (below), check valve is tightly closed.
Hint: if the valve could not be closed, it is required to
replace temperature regulator.67

Cooling - Water pump assemblyWater pump assemblyReplacement1. Remove engine right bottom shield.
2. Discharge engine coolant.
3. Remove drive belt.Slowly turn drive belt tensioner clockwise to loosen the belt;
then remove drive belt and put back drive belt tensioner slowly
to completely loosen the tensioner.4. Remove alternator assembly.(a) Remove rubber cover and nuts.
(b) Uncouple alternator joint.
(c) Remove 2 bolts and alternator.5. Remove water pump assembly.Remove 6 bolts, water pump and o-ring.69

Cooling - Water pump assembly6. Install water pump assembly.(a) Install new o-ring on water pump.
(b) Install water pump with 6 bolts.
Torque: bolt A: Bolt B: 7. Install alternator mounting components.Torque: 12mm bolt head: 14mm bolt head: 8. Refill engine coolant.
9. Check there is leakage with coolant.
70