2008 GEELY FC light

Engine cover/automobile door--Front automobile door 368 Name of parts Specification Amount Marked
number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33Number of parts
68000147
68000162
68000149
Q1860610
68000159
67000157
Q32006
68000153
Q2580816
Q1860610
JQ2756316
67000123
Q1860610
68000145
Q2716319
67000132
68000144
Q2714216
68010050
Q2204816
67000107
68000141
68000160
62000479
62000025
62000024
Q1840820
68000163JQ1840816T1F31Q1400616
62000027
68010052
68000151Right front glass assembly
Seal tape of right front glass leading slot
Right front glass leading slot assembly
Hexagon flange face bolt
Exterior seal tape of right front door glass
Right exterior electric rearview mirror assembly
Hexagon flange face nut
Right front door locker organization assembly
Inner hexagon floriated raised countersunk head screw
Hexagon flange face bolt
Combination part of hexagon head self-tapping screw with flat gasket
Right front door glass lift assembly
Hexagon flange face bolt
Right front door board bracket
Cross slot plate head self-tapping screw
Right front small speaker cover assembly
Right front door control panel assembly
Freerson plate head self-tapping screw
Right front door inner defending board assemblyCombination part of cross slot plate head self-tapping screw with flat washerDoor light assembly
Right front door defender water curtain assembly
Right front door seal tape assembly
Right front door assembling assembly
Right front door upper hinge assembly
Hexagon flange face bolt (with step)
Hexagon flange face bolt
Front door limiter assembly
Hexagon flange face bolt
Combination part of hexagon head bolt with flat washer
Right front door lower hinge assembly
Right side door inner handle assembly
Right front door exterior handle assembly1
1
1
1
1
1
3
1
3
2
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
2
4
2
2
2
1
2
1M6 × 10
M6
M6× 18
M6× 10
ST6.3 × 16
M6 × 10
ST6.3 × 19
ST4.2 × 16
ST4.8 × 16
M8× 20
M8× 20
M8× 16
M8× 16

Engine cover/automobile door--Front automobile door
Overhaul
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special
specification.
zOverhaul procedure for right side is same as the left side.
zPlease refer to subassembly figure of front door on page 360.
1. Disassemble left front door control panel assembly [68000142]
(a) Disassemble the screw.
(b) Use screw driver to disassemble left front door control panel assembly.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
(c) Disassemble the joint.
2. Disassemble left front door inner defending board assembly [68010049]
(a) Disassemble the screw.
(b) Without equipping with door control light: use screw driver to disassemble door inner defending board
assembly.
(c) Equipping with door control light: use screw driver to disassemble door inner defending board assembly,
then disassemble the joint again.
(d) Equipping with door control light: use screw driver to disassemble door control light.
3. Disassemble left door inner handle assembly [68010051]
(a) Disassemble inner handle, and disassemble two pull cables from inner handle.
4. Disassemble repairing hole cover of left front door
5. Disassemble left front small loudhail cover assembly [67000131]
 369  6. Disassemble left exterior electric rearview mirror
assembly [67000155]
(a) Disassemble the joint.
(b) Disassemble three screw caps and left exterior electric
rearview mirror.
7. Disassemble exterior seal tape of left front door glass
[68000158]

Engine cover/automobile door--Front automobile door
Adjustment
Hint: the working procedure for right side is same as left side.
1. Check the clearance of left front door
(a) Check whether following data is in standard value.
2. Adjust the clearance of left front door.
(a) Use special tool to loosen hinge bolt at the side of automo-
bile body to adjust the door.
Torque: 26 N
⋅ ⋅⋅ ⋅
⋅m
(b) Loosen hinge bolt at the side of automobile body to adjust
the door.
Torque: 26 N
⋅ ⋅⋅ ⋅
⋅m
(c) Loosen lightly fixing screw of locking pedestal and use plas-
tic hammer to knock lightly locking pedestal to adjust its
position.
(d) Lock fixing screw of locking pedestal again.
Torque: 23 N
⋅ ⋅⋅ ⋅
⋅m
At the side of
automobile bodyAt the side of
automobile door
 372 
At the side of
automobile door At the side of
automobile body

Engine cover/automobile door--Rear automobile door
2. Adjust the clearance of left rear door.
(a) Loosen hinge screw cap at the side of automobile body to
adjust the door.
Torque: 26 N
⋅ ⋅⋅ ⋅
⋅m
(b) Loosen hinge screw cap at the side of automobile door to
adjust the door.
Torque: 26 N
⋅ ⋅⋅ ⋅
⋅m
(c) Loosen lightly fixing screw of locker pedestal, and use plastic
hammer to knock lightly the locker pedestal to adjust its
position.
(d) Lock the fixing screw of locker pedestal again.
Torque: 23 N
⋅ ⋅⋅ ⋅
⋅m
At the side of
automobile body
 376 
At the side of
automobile bodyAt the side of
automobile door
At the side of
automobile door

Engine cover/automobile door--Trunk cover
Trunk cover
Adjustment
1. Check the clearance of trunk cover.
(a) Check whether following data is in standard value.
2. Adjust the clearance of trunk cover.
(a) If you want to make front and rear, left and right adjustment,
please loosen the bolt at first.
(b) If the front end of trunk cover needs to adjust vertically, please
increase or decrease the number of washers between hinge
and trunk cover.
Torque: 7.0 N
⋅ ⋅⋅ ⋅
⋅m
(c) Use the hammer and copper stick to knock lightly the locker
pedestal to adjust.
Torque: 5.5 N
⋅ ⋅⋅ ⋅
⋅m
 377 

Exterior/inner trim board--Front bumper
Exterior/inner trim board
Front bumper
Subassembly
Inner gasket of
right front wheel
Inner gasket of
left front wheel Fixing pedestal of
radar probe
Radar probe head
Radar probe head
Fixing pedestal of
radar probe head
Front fog light assemblyRadiator cover
assembly
Front bumper
Equipping with fog light
 379 

Exterior/inner trim board--Front bumper
Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of front bumper on page 379.
1. Disassemble radiator cover assembly [68000094]
(a) Disassemble the bolt and radiator cover assembly.
2. Disassemble inner gasket of left front wheel [68000225]
(a) Use disassembling tool for fixing clamp to disassemble two fixing clamps.
(b) Disassemble the screw and a part of inner gasket of left front wheel.
Hint: Disassemble the fixing clamp of screw and inner gasket of left front wheel in the scope of
front bumper which could be disassembled.
3. Disassemble inner gasket of right front wheel [68000228]
4. Disassemble front bumper [68000005]
(a) Disassemble four screws and two fixing clamps.
(b) Disassemble fixing clasp and front bumper.
(c) Equipping with fog light: disassemble two joints of fog light.
(d) Equipping with radar probe head: disassemble two radar probe heads (luxury type).
5. Disassemble reversing radar probe head assembly.
(a) Disassemble two fixing pedestals of radar probe head and two radar probe heads.
6. Disassemble left front fog light assembly [67000098]
(a) Disassemble fixing clasp and left front fog light assembly.
7. Disassemble right front fog light assembly [67000099]
 380 

Change
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction.
zPlease refer to subassembly figure of rear bumper on page 381.
Exterior/inner trim board--Rear bumper
 382  1. Disassemble trunk carpet assembly [68000114]
2. Disassemble rear trim board of trunk [68000118]
(a) Use two fixing clasps.
(b) Use disassembling tool for trim tape to disassemble rear
trim board of trunk.
3. Disassemble left decoration of trunk [68000112]
(a) Use disassembling tool for fixing clamp to disassemble
fixing clamp and a part of left decoration of trunk.
Hint:
Disassemble the fixing clasp and left decoration of trunk in the scope of screw cap used for
fixing rear bumper and trunk which could be disassembled.
4. Disassemble right decoration of trunk [68000113]
5. Disassemble mudguard of left rear wheel [68000223]
(a) Disassemble two screws and mudguard of left rear wheel.
6. Disassemble mudguard of right rear wheel [68000224]
7. Disassemble trim board of left rear wheel [68000230]
(a) Use screw driver to disassemble fixing clasp from rear bumper.
(b) Use disassembling tool for fixing clasp to disassemble fix-
ing clasp.
(c) Disassemble trim board of left rear wheel.
Hint: Disassemble trim board of left rear wheel in the
scope of screw used for fixing rear bumper which could
be disassembled.
8. Disassemble trim board of right rear wheel [68000231]
9. Disassemble rear bumper [68000012]
(a) Use screw driver to disassemble two fixing clasps.
(b) Disassemble four screw caps and two screws.
(c) Disassemble fixing clasp and rear bumper.
(d) Equipping with radar probe head: disassemble four joints of
radar probe head.
10. Disassemble reversing radar probe head assembly.
(a) Disassemble fixing pedestal of radar probe and radar probe.
11. Disassemble left rear fog light assembly [67000100]
(a) Disassemble fixing nut and left rear fog light assembly.
12. Disassemble right rear fog light assembly [67000101]