2007 NISSAN TIIDA reverse

SB-12
< ON-VEHICLE REPAIR >
TOP TETHER STRAP CHILD RESTRAINT
TOP TETHER STRAP CHILD RESTRAINT
Removal and InstallationINFOID:0000000001366763
REMOVAL
1. Disconnect the negative battery cable.
2. Remove the rear parcel shelf finisher. Refer to INT-26, "
Removal and Installation".
3. Remove the bolt (A), then remove the top tether bracket (1) from
the body panel.
INSTALLATION
Installation is in the reverse order of removal.
LHIA0134E

FRONT SEAT
SE-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
1. Remove the rear leg covers.
2. Remove the front leg covers.
3. Remove the mounting bolts on the back side of the front seat. (TORX bolt: T50)
4. Remove the mounting bolts on the front side of the front seat. (TORX bolt: T50)
5. Disconnect the harness connector under the seat and remove harness securing clips.
CAUTION:
Before removal, be sure to turn ignition switch OFF, disconnect both battery cables, and then wait
for at least 3 minutes.
6. Set seatback in a neutral position, and then remove front seat from the vehicle.
Installation
Install in the reverse order of removal. Be careful of the following three points.
 Before the installation, confirm that the inside and outside slide rails are locked at the same positions.
 Confirm that the slide rail location pin is set to the hole on the floor.
 Clamp the harness in position.
PIIB2669J
PIIB2668J

REAR SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
4. Fold the left seatback and remove the seatback mounting bolts
(A) from the left rear seat back brackets. Remove the seatback
from the vehicle.
5. Remove the kicking plate rear inner. Refer to INT-20, "
Removal and Installation" .
6. Remove the bolt under the seatback side.
7. Pull seatback side up, and then remove seatback side.
8. Remove the bolts, and then remove rear seatback center bracket.
9. Remove the bolt, and then remove rear seatback side bracket
from the vehicle.
10. Remove the rear seatback finisher. Refer to INT-20, "
Removal and Installation" .
11. Remove the bolts, and then remove the rear seat striker.
Installation
Installation is the reverse order of removal. Be careful of the following point.
 Seatback assembly and rear seatback side bracket installation procedure.
WIIA1383E
PIIB2482J
PIIB2483J
PIIB2484J

SE-20
< REMOVAL AND INSTALLATION >
REAR SEAT
1. Install the rear seatback side bracket in the vehicle.
2. Temporarily tighten the seatback assembly and rear seatback side bracket.
3. Lift to fold up seatback assembly. Be sure to lock seatback assembly to rear seat striker.
4. Tighten the bolt.
NOTE:
Confirm that side hinge bracket location pin is set to the hole on the seatback backside.
Removal and InstallationINFOID:0000000001710910
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
60:40 SPLIT FOLD DOWN SLIDING SEAT
Removal
1. Remove the front leg covers. Remove the front anchor bolts.
2. Remove the rear leg covers. Remove the front anchor bolts.
3. Remove the seat assembly.
Installation
Installation is the reverse order of removal.
PIIB2484J
WIIA1307E
WIIA1380E

FRONT SEAT
SE-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
2. Remove the hog rings to separate the seat cushion pad and seat cushion trim.
3. Remove seat cushion trim and seat cushion pad from the seat cushion frame.
Assembly
Assembly is the reverse order of removal.
SEAT CUSHION FRAME
Disassembly
1. Remove the seat cushion trim and pad. Refer to "SEAT CUSHION TRIM AND PAD" .
2. Remove the seat cushion finisher B. (Driver seat)
3. Remove the seat cushion lower finisher.
4. Remove the front seat belt buckle.
Assembly
Assembly is the reverse order of removal.
PIIB2607E
PIIB2609E

SE-26
< ON-VEHICLE REPAIR >
REAR SEAT
Disassembly and Assembly
INFOID:0000000001710914
60:40 SPLIT FOLD DOWN SLIDING SEAT
Disassembly of Armrest
1. Fold up the backside of the seatback trim and then remove the
armrest nuts.
2. Push the armrest toward left side while pulling backward to
remove.
3. Remove the rear seat bushing, and then remove the armrest
hinge cover by pulling it backward.
Assembly of Armrest
Assembly in the reverse order of disassembly.
Disassembly of Seatback Trim and Pad
1. Remove the headrest.
1. Seat cushion trim 2. Seat cushion pad 3. Seatback side
4. Armrest 5. Rear seat bushing 6. Armrest hinge cover
7. Headrest 8. Headrest holder (free) 9. Headrest holder (locked)
10. Striker cover 11. Seatback trim 12. Seatback pad
13. Rear seatback lock knob 14. Rear seat lock assembly 15. Seatback frame
16. Rear seatback center bracket 17. Rear seatback side bracket 18. Rear seat striker
19. Seat cushion hook 20. Seatbelt guide
PIIB2913J
PIIB2915J
PIIB6507E

REAR SEAT
SE-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
2. Remove the retainer under the back of seatback.
3. Remove the headrest holder.
4. To remove armrest, refer to "Disassembly of Armrest " .
5. Remove the seatback trim.
6. Remove the seatback pad from the seatback frame.
7. Remove the seatback center bracket bolt and then remove the seatback frame.
Assembly of Seatback Trim and Pad
Assembly is the reverse order of disassembly. Be careful of the following one point.
 Before installing headrest holder, check its orientation (front/rear and right/left).
Disassembly of Seat Cushion Trim and Pad
Remove the rings to separate the trim and pad.
Assembly of Seat Cushion Trim and Pad
Assembly is the reverse order of disassembly.
Disassembly and AssemblyINFOID:0000000001710917
60:40 SPLIT FOLD DOWN FIXED SEAT
Disassembly of Armrest
1. Fold down the armrest and remove the armrest bolt cover (A).
PIIB2486J
PIIB4084J
WIIA1384E

SE-28
< ON-VEHICLE REPAIR >
REAR SEAT
2. Remove the armrest bolt (A).
3. Push the armrest toward left side while pulling backward to
remove.
4. Remove the rear seat bushing, and then remove the armrest
hinge cover by pulling it backward.
Assembly of Armrest
Assembly in the reverse order of disassembly.
Disassembly of Seatback Trim and Pad
1. Remove the headrest.
2. Remove the retainer under the back of seatback.
WIIA1385E
PIIB2915J
PIIB6507E
PIIB2486J