2007 KIA CARNIVAL battery

Distance[in (mm)]1.57+0.19/0
(40+5/0) 1.57+0.19/0
(40+5/0)
2. Set the washer nozzle on the specified spray position.
INSPECTION
SPEED OPERATION CHECK
1. Remove the connector from the wiper motor.
2. Attach the positive (+) lead from the battery to terminal 4 and the negative ( - ) lead to terminal 1.
3. Check that the motor operates at low speed.
4. Connect the positive (+) lead from the battery to terminal 5 and the negative ( - ) lead to terminal 1.
5. Check that the motor operates at high speed.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the front bumper cover. (Refer to Body group - Front bumper)
3. Remove the washer hose, the washer motor connector (A) and washer level sensor connector (C).
4. Remove the washer reservoir after removing 2 bolts and 1 step bolt.
5.Installation is the reverse of removal.
INSPECTION
1.With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
2. Connect positive (+) battery cables to terminal 2 and negative ( - ) battery cables to terminal 1 respectively.
3. Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles. If they
are abnormal, replace the washer motor.

5.Installation is the reverse of removal.
INSTALLATION
1.Install the rear wiper arm and blade to the specified position.
※ Specified position : The first defogger line from bottom of the rear window.
2. Set the rear washer nozzle on the specified spray position.
INSPECTION
1.Remove the 3P connector from the rear wiper motor.
2. Connect battery positive (+) and negative ( - ) cables to terminals 2 and 1 respectively.
3. Check that the motor operates normally. Replace the motor if it operates abnormally.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
2. Remove the front bumper. (Refer to the Body group - Front bumper)
3. Connect positive (+) and negative ( - ) battery cables to terminals 3 and 1 respectively to see that the washer motor
runs and water is pumped.
4. Check that the motor operates normally.
Replace the motor if it operates abnormally.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the lens and open the sunglass case cover from the overhead console then remove the 2 screws holding
the overhead console. And disconnect the connector then remove the overhead console lamp assembly from the
headliner.
3.Check for continuity between the terminals. If the continuity is not as specified, replace the sunroof switch.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the overhead console and loosen sunroof motor bracket (A) mounting bolts (4EA).
3.Remove sunroof motor mounting screw (3EA) and disconnect connector (10pin). And then remove the sun roof
motor.
RESETTING THE SUNROOF
Whenever the vehicle battery is disconnected or discharged, or you use the emergency handle to operate the sunroof,
you have to reset your sunroof system as follows :
1. Turn the ignition key to the ON position. Press and hold the TILT UP button more than 15s until the sunroof has
tilted upward/downward slightly.
2. When this is complete, Press and hold the TILT UP button once again until the sunroof has raised above and
returned to the maximum TILT UP position.
When this is complete, the sunroof system is reset.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Loose the mounting bolts (2EA).
3.Remove the head lamp assembly after disconnecting the lamp connectors.
Take care that holding clip (A) is not to be damaged.
4.Remove the head lamp rear cover and pulling up head lamp bulb fixing wire clip.
5.Replace the bulb.
6. Installation is the reverse of removal.
HEAD LAMP AIMING INSTRUCTIONS
Alternately turn the adjusting gear to adjust the head lamp aiming. If beam- setting equipment is not available, proceed
as follows :
1. Inflate the tires to the specified pressure and remove any loads from the vehicle except the driver, spare tire, and
tools.

2.The vehicle should be placed on a flat floor.
3. Check the suspension spring.
4. Draw vertical lines (Vertical lines passing through respective head lamp centers) and a horizontal line (Horizontal
line passing through center of head lamps) on the screen.
5. With the head lamp and battery in normal condition, aim the head lamps so the brightest portion falls on the
horizontal and vertical lines.
Make vertical and horizontal adjustments to the lower beam using the adjusting wheel.
FRONT FOG LAMP AIMING
The front fog lamps should be aimed as the same manner used to adjust the head lamps.
With the front fog lamps and battery normal condition, aim the front fog lamps by turning the adjusting gear (A).
HEAD LAMP AND FOG LAMP AIMING POINT