2007 KIA CARNIVAL battery

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT POWER WINDOW MOTOR
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Remove the window motor (B) after disconnecting the motor connector (A) and mounting nuts.
4.Installation is the reverse of removal.
SLIDING POWER WINDOW MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Remove the door trim seal and glass.
4. Remove the door regulator.
5. Remove the power window motor (A) after disconnecting the motor connector and power window motor mounting
nuts.
6.Installation is the reverse of removal.
QUARTER GLASS MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)

3.Remove the quarter glass motor (B) after disconnecting the motor connector (A) and quarter glass motor mounting
bolts and screws.
4.Installation is the reverse of removal.
INSPECTION
FRONT POWER WINDOW MOTOR INSPECTION
1. Remove ( - ) negative battery terminal.
2. Remove the rear door trim panel. (Refer to the Body group - front door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage (12V) and check that the motor operates smoothly. Next,
reverse the polarity and check that the motor operates smoothly in the reverse direction. If the operation is
abnormal, replace the motor.
SLIDING POWER WINDOW MOTOR INSPECTION

1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.
QUARTER GLASS MOTOR INSPECTION
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
DRIVER/ASSIST DOOR MODULE (DDM/ADM)
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Disconnect the door module mounting screws (5EA) after disconnecting the module connectors (3EA) from the
motor.
4.Remove the door module (DDM/ADM) (A) from the front door trim panel.
5.Installation is the reverse of removal.
SLIDING POWER WINDOW SWITCH
1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the sliding power window switch (A) from the B pillar trim (C).
3.Installation is the reverse of removal.
QUARTER GLASS SWITCH

1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the quarter glass switch (A) from the rear cargo area luggage trim.
3.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Remove the cowl top cover.(Refer to the wiper)
2. Disconnect the windshield deicer connector (A) from the wiper motor linkage.
3.Check for continuity between the terminals of deicer lines.
4.Turn the ignition switch ON and the windshield deicer switch ON, then measure the voltage between the terminals
of harness side deicer connector.
O K: approx. Battery voltage (12V)

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the console lower cover (A).
3.Remove the center facia panel(A) after loosening screws. Take care not to damage fixing clips.
4.Remove the windshield deicer switch from the center facia panel switch.
5.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center facia panel, console lower cover and center air vent (A) after loosening screws. Take care not
to damage fixing clips.
3.Remove the center facia panel switch and air control panel (A) after loosening screws.
4.Disconnect the air control panel connector (A).
5.Installation is the reverse of removal.