2007 INFINITI M35 component

ATC-2Revision: 2007 April2007 M35/M45 AUTO SWITCH ................................................... 34
DEFROSTER (DEF) SWITCH ............................. 34
UPPER VENT SWITCH ...................................... 34
A/C SWITCH ....................................................... 35
FAN SWITCHES .................................................. 35
OFF SWITCH ...................................................... 35
REAR WINDOW DEFOGGER SWITCH ............. 35
INTAKE SWITCH ................................................. 35
DUAL SWITCH .................................................... 35
Control Operation (Rear Control Switch) ................ 35
AUTO SWITCH ................................................... 35
FAN SWITCH ...................................................... 35
REAR TEMPERATURE CONTROL SWITCH ..... 36
Fail-Safe Function .................................................. 36
Discharge Air Flow ................................................. 37
System Description ................................................. 38
SWITCHES AND THEIR CONTROL FUNCTION ... 38
CAN Communication System Description .............. 39
TROUBLE DIAGNOSIS ............................................ 40
CONSULT-II Function (ECM) .................................. 40
CONSULT-II BASIC OPERATION ....................... 40
DATA MONITOR .................................................. 40
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 40
WORK FLOW ...................................................... 40
SYMPTOM TABLE .............................................. 41
Component Parts and Harness Connector Location ... 42
ENGINE COMPARTMENT .................................. 42
PASSENGER COMPARTMENT .......................... 43
Schematic ............................................................... 44
Wiring Diagram —A/C— ......................................... 46
Auto Amp. Terminals and Reference Value ............ 54
PIN CONNECTOR TERMINAL LAYOUT ............ 54
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 54
Self-diagnosis Function .......................................... 56
DESCRIPTION .................................................... 56
FUNCTION CONFIRMATION PROCEDURE ...... 57
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 63
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 64
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 64
Operational Check .................................................. 65
CHECKING MEMORY FUNCTION ..................... 65
CHECKING BLOWER ......................................... 65
CHECKING DISCHARGE AIR (MODE SWITCH
AND DEF SWITCH) ............................................ 65
CHECKING DISCHARGE AIR (UPPER VENT
SWITCH) ............................................................. 66
CHECKING INTAKE AIR ..................................... 66
CHECKING TEMPERATURE DECREASE ......... 66
CHECKING TEMPERATURE INCREASE .......... 66
CHECKING A/C SWITCH ................................... 66
CHECKING AUTO MODE ................................... 66
Power Supply and Ground Circuit for Auto Amp. ... 67
INSPECTION FLOW ........................................... 67
COMPONENT DESCRIPTION ............................ 68DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 68
Rear Control Switch Circuit ..................................... 70
DIAGNOSIS PROCEDURE FOR REAR CON-
TROL SWITCH .................................................... 70
LAN System Circuit ................................................. 71
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 71
Mode Door Motor Circuit ......................................... 76
INSPECTION FLOW ............................................ 76
SYSTEM DESCRIPTION ..................................... 77
COMPONENT DESCRIPTION ............................ 78
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ................................................................ 78
Upper Ventilator Door Motor Circuit ........................ 79
INSPECTION FLOW ............................................ 79
SYSTEM DESCRIPTION ..................................... 80
COMPONENT DESCRIPTION ............................ 81
DIAGNOSIS PROCEDURE FOR UPPER VEN-
TILATOR DOOR MOTOR .................................... 81
Air Mix Door Motor Circuit ....................................... 82
INSPECTION FLOW ............................................ 82
SYSTEM DESCRIPTION ..................................... 83
COMPONENT DESCRIPTION ............................ 84
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR ................................................................ 84
Air Mix Door Motor PBR Circuit .............................. 84
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR ....................................................... 84
Intake Door Motor Circuit ........................................ 85
INSPECTION FLOW ............................................ 85
SYSTEM DESCRIPTION ..................................... 86
COMPONENT DESCRIPTION ............................ 87
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ................................................................ 87
Blower Motor Circuit ................................................ 88
INSPECTION FLOW ............................................ 88
SYSTEM DESCRIPTION ..................................... 89
COMPONENT DESCRIPTION ............................ 90
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ................................................................ 90
COMPONENT INSPECTION ............................... 92
Magnet Clutch Circuit .............................................. 93
INSPECTION FLOW ............................................ 93
SYSTEM DESCRIPTION ..................................... 94
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH .............................................................. 94
COMPONENT INSPECTION ............................... 97
Insufficient Cooling .................................................. 98
INSPECTION FLOW ............................................ 98
PERFORMANCE TEST DIAGNOSIS ................100
PERFORMANCE CHART ..................................102
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE .................................................................104
DIAGNOSIS PROCEDURE FOR INSUFFI-
CIENT COOLING ...............................................106
Insufficient Heating ...............................................108
INSPECTION FLOW ..........................................108
Noise .....................................................................109
INSPECTION FLOW ..........................................109
Self-diagnosis .......................................................110

ATC-3
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45 INSPECTION FLOW .......................................... 110
Memory Function ................................................. . 111
INSPECTION FLOW ......................................... . 111
Ambient Sensor Circuit ......................................... 112
COMPONENT DESCRIPTION .......................... 112
AMBIENT TEMPERATURE INPUT PROCESS .. 112
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR ............................................................ 112
COMPONENT INSPECTION ............................. 114
In-vehicle Sensor Circuit ....................................... 115
COMPONENT DESCRIPTION .......................... 115
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR ............................................................ 116
COMPONENT INSPECTION ............................. 117
Sunload Sensor Circuit ......................................... 118
COMPONENT DESCRIPTION .......................... 118
SUNLOAD INPUT PROCESS ........................... 118
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR ............................................................ 118
COMPONENT INSPECTION ............................ 120
Intake Sensor Circuit ............................................ 121
COMPONENT DESCRIPTION ......................... 121
DIAGNOSIS PROCEDURE FOR INTAKE SEN-
SOR .................................................................. 121
COMPONENT INSPECTION ............................ 122
CONTROLLER ....................................................... 123
Removal and Installation of Multifunction Switch . 123
REMOVAL ......................................................... 123
INSTALLATION ................................................. 123
AUTO AMP ............................................................. 124
Removal and Installation of Unified Meter and A/C
Auto Amp. ............................................................ 124
REMOVAL ......................................................... 124
INSTALLATION ................................................. 124
AMBIENT SENSOR ................................................ 125
Removal and Installation ...................................... 125
REMOVAL ......................................................... 125
INSTALLATION ................................................. 125
IN-VEHICLE SENSOR ............................................ 126
Removal and Installation ...................................... 126
REMOVAL ......................................................... 126
INSTALLATION ................................................. 126
SUNLOAD SENSOR .............................................. 127
Removal and Installation ...................................... 127
REMOVAL ......................................................... 127
INSTALLATION ................................................. 127
INTAKE SENSOR ................................................... 128
Removal and Installation ...................................... 128
REMOVAL ......................................................... 128
INSTALLATION ................................................. 128
BLOWER UNIT ....................................................... 129
Removal and Installation ...................................... 129
REMOVAL ......................................................... 129
INSTALLATION ................................................. 129
Disassembly and Assembly ................................. 130
BLOWER MOTOR .................................................. 131
Removal and Installation ...................................... 131
REMOVAL ......................................................... 131
INSTALLATION ................................................. 131INTAKE DOOR MOTOR .........................................132
Removal and Installation ......................................132
REMOVAL .........................................................132
INSTALLATION .................................................132
IN-CABIN MICROFILTER .......................................133
Removal and Installation ......................................133
FUNCTION ........................................................133
REPLACEMENT TIMING ..................................133
REPLACEMENT PROCEDURES .....................133
HEATER & COOLING UNIT ASSEMBLY ...............134
Removal and Installation ......................................134
REMOVAL .........................................................134
INSTALLATION .................................................135
Disassembly and Assembly ..................................137
MODE DOOR MOTOR ............................................139
Removal and Installation ......................................139
REMOVAL .........................................................139
INSTALLATION .................................................139
AIR MIX DOOR MOTOR .........................................140
Removal and Installation ......................................140
REMOVAL .........................................................140
INSTALLATION .................................................140
UPPER VENTILATOR DOOR MOTOR ..................141
Removal and Installation ......................................141
REMOVAL .........................................................141
INSTALLATION .................................................141
HEATER CORE .......................................................142
Removal and Installation ......................................142
REMOVAL .........................................................142
INSTALLATION .................................................142
DUCTS AND GRILLES ...........................................143
Removal and Installation ......................................143
COMPONENT LAYOUT ....................................143
REMOVAL .........................................................145
INSTALLATION .................................................149
REFRIGERANT LINES ...........................................150
HFC-134a (R-134a) Service Procedure ...............150
SETTING OF SERVICE TOOLS AND EQUIP-
MENT ................................................................150
Components .........................................................152
VQ35DE ............................................................152
VK45DE .............................................................153
Removal and Installation of Compressor ..............153
REMOVAL .........................................................153
INSTALLATION .................................................156
Check Disc to Pulley Clearance ...........................156
Removal and Installation of Low-pressure Flexible
Hose and Pipe ......................................................157
REMOVAL .........................................................157
INSTALLATION .................................................157
Removal and Installation of High-pressure Flexible
Hose .....................................................................158
REMOVAL .........................................................158
INSTALLATION .................................................159
Removal and Installation of High-pressure Pipe 1
(Engine Compartment) .........................................159
REMOVAL .........................................................159
INSTALLATION .................................................160
Removal and Installation of Low-pressure Pipe 1

ATC-6
PRECAUTIONS
Revision: 2007 April2007 M35/M45
Precautions for Procedures without Cowl Top CoverNJS000FP
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precautions for Working with HFC-134a (R-134a)NJS000FQ
CAUTION:

CFC-12 (R-12) refrigerant and HFC-134a (R-134a) refrigerant are not compatible. If the refrigerants
are mixed and compressor malfunction is likely to occur, refer to “CONTAMINATED REFRIGER-
ANT” below. To determine the purity of HFC-134a (R-134a) in the vehicle and recovery tank, use
Refrigerant Recovery/Recycling Recharging equipment and Refrigerant Identifier.

Use only specified lubricant for the HFC-134a (R-134a) A/C system and HFC-134a (R-134a) compo-
nents. If lubricant other than that specified is used, compressor malfunction is likely to occur.

The specified HFC-134a (R-134a) lubricant rapidly absorbs moisture from the atmosphere. The fol-
lowing handling precautions must be observed:
–When removing refrigerant components from a vehicle, immediately cap (seal) the component to
minimize the entry of moisture from the atmosphere.
–When installing refrigerant components to a vehicle, never remove the caps (unseal) until just
before connecting the components. Connect all refrigerant loop components as quickly as possi-
ble to minimize the entry of moisture into system.
–Only use the specified lubricant from a sealed container. Immediately reseal containers of lubri-
cant. Without proper sealing, lubricant will become moisture saturated and should not be used.
–Never allow lubricant (Nissan A/C System Oil Type S) to come in contact with styrene foam parts.
Damage may result.
PIIB3706J

PRECAUTIONS
ATC-7
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
CONTAMINATED REFRIGERANT
If a refrigerant other than pure HFC-134a (R-134a) is identified in a vehicle, take appropriate steps
shown below:

Explain to the customer that environmental regulations prohibit the release of contaminated refrigerant
into the atmosphere.

Explain that recovery of the contaminated refrigerant could damage service equipment and refrigerant
supply.

Suggest the customer return the vehicle to the location of previous service where the contamination may
have occurred.

In case of repairing, recover the refrigerant using only dedicated equipment and containers. Never
recover contaminated refrigerant into the existing service equipment. If the facility does not have
dedicated recovery equipment, contact a local refrigerant product retailer for available service. This refrig-
erant must be disposed of in accordance with all federal and local regulations. In addition, replacement of
all refrigerant system components on the vehicle is recommended.

If the vehicle is within the warranty period, the air conditioner warranty is void. Please contact Nissan Cus-
tomer Affairs for further assistance.
General Refrigerant PrecautionsNJS000FR
WARNING:

Avoid breathing A/C refrigerant and lubricant vapor or mist. Exposure may irritate eyes, nose and
throat. Remove HFC-134a (R-134a) from the A/C system, using certified service equipment meet-
ing requirements of SAE J-2210 [HFC-134a (R-134a) recycling equipment], or J-2209 [HFC-134a (R-
134a) recovery equipment]. If accidental system discharge occurs, ventilate work area before
resuming service. Additional health and safety information may be obtained from refrigerant and
lubricant manufacturers.

Never release refrigerant into the air. Use approved recovery/recycling equipment to capture the
refrigerant every time an air conditioning system is discharged.

Always wear eye and hand protection (goggles and gloves) when working with any refrigerant or
air conditioning system.

Never store or heat refrigerant containers above 52°C (126°F).

Never heat a refrigerant container with an open flame; if container warming is required, place the
bottom of the container in a warm pail of water.

Never intentionally drop, puncture, or incinerate refrigerant containers.

Keep refrigerant away from open flames: poisonous gas will be produced if refrigerant burns.

Refrigerant will displace oxygen, therefore be certain to work in well ventilated areas to prevent
suffocation.

Never pressure test or leak test HFC-134a (R-134a) service equipment and/or vehicle air condition-
ing systems with compressed air during repair. Some mixtures of air and HFC-134a (R-134a) have
been shown to be combustible at elevated pressures. These mixtures, if ignited, may cause injury
or property damage. Additional health and safety information may be obtained from refrigerant
manufacturers.
Precautions for Refrigerant ConnectionNJS000FS
A new type refrigerant connection has been introduced to all refrigerant lines except the following location.

Expansion valve to evaporator

Refrigerant pressure sensor to liquid tank
ABOUT ONE-TOUCH JOINT
Description

One-touch joints are pipe joints which do not require tools during piping connection.

Unlike conventional connection methods using union nuts and flanges, controlling tightening torque at
connection point is not necessary.

When removing a pipe joint, use a disconnector.

ATC-8
PRECAUTIONS
Revision: 2007 April2007 M35/M45
COMPONENT PARTS
FUNCTIONS OF COMPONENT PARTS
NOTE:

Garter spring (2) cannot be removed from cage (A) of male-side piping.

Indicator ring (3) remains near piping connection point, however, this is not a malfunction. (This is to
check piping connection during factory assembly.)
REMOVAL
1. Clean piping connection point, and set a disconnector.
1 Pipe (Male side)
Retains O-rings (4).

Retains garter spring (2) in cage (A).
2 Garter spring Anchors female side piping (5).
3 Indicator ringWhen connection is made properly, this is ejected from male-side piping (1). (This part is no longer
necessary after connection.)
4 O-ring Seals connection point. (Not reusable)
5 Pipe (Female side)

Seals connection by compressing O-rings (4).

Anchors piping connection using flare (B) and garter spring (2).
RJIA4383J
SJIA0106E

ATC-12
PRECAUTIONS
Revision: 2007 April2007 M35/M45
WARNING:
Make sure all refrigerant is discharged into the recycling equipment and the pressure in the system is
less than atmospheric pressure. Then gradually loosen the discharge side hose fitting and remove it.
CAUTION:
When replacing or cleaning refrigerant cycle components, observe the following.

When the compressor is removed, store it in the same way at it is when mounted on the car. Fail-
ure to do so will cause lubricant to enter the low-pressure chamber.

When connecting tubes, always use a torque wrench and a back-up wrench.

After disconnecting tubes, immediately plug all openings to prevent entry of dust and moisture.

When installing an air conditioner in the vehicle, connect the pipes at the final stage of the opera-
tion. Never remove the seal caps of pipes and other components until just before required for con-
nection.

Allow components stored in cool areas to warm to working area temperature before removing seal
caps. This prevents condensation from forming inside A/C components.

Thoroughly remove moisture from the refrigeration system before charging the refrigerant.

Always replace used O-rings.

When connecting tubes, apply lubricant to circle of the O-rings shown in illustration. Be careful
not to apply lubricant to threaded portion.

O-ring must be closely attached to the groove of tube.

When replacing the O-ring, be careful not to damage O-ring and tube.

Connect tube until a click can be heard, then tighten the nut or bolt by hand. Make sure that the O-
ring is installed to tube correctly.

After connecting line, perform leak test and make sure that there is no leakage from connections.
When the refrigerant leaking point is found, disconnect that line and replace the O-ring. Then
tighten connections of seal seat to the specified torque.
Precautions for Servicing CompressorNJS000FT

Plug all openings to prevent moisture and foreign matter from entering.

When the compressor is removed, store it in the same way at it is when mounted on the car.

When replacing or repairing compressor, follow “Maintenance of Lubricant Quantity in Compres-
sor” exactly. Refer to AT C - 2 6 , "
Maintenance of Lubricant Quantity in Compressor" .

Keep friction surfaces between clutch and pulley clean. If the surface is contaminated with lubri-
cant, wipe it off by using a clean waste cloth moistened with thinner.Name : Nissan A/C System Oil Type S
RHA861F

PRECAUTIONS
ATC-15
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
Precautions for Leak Detection DyeNJS000FV

The A/C system contains a fluorescent leak detection dye used for locating refrigerant leaks. An ultraviolet
(UV) lamp is required to illuminate the dye when inspecting for leaks.

Always wear fluorescence enhancing UV safety goggles to protect your eyes and enhance the visibility of
the fluorescent dye.

The fluorescent dye leak detector is not a replacement for an electrical leak detector (SST: J-41995). The
fluorescent dye leak detector should be used in conjunction with an electrical leak detector (SST: J-41995)
to pin-point refrigerant leaks.

For the purpose of safety and customer’s satisfaction, read and follow all manufacture’s operating instruc-
tions and precautions prior to performing the work.

A compressor shaft seal should not necessarily be repaired because of dye seepage. The compressor
shaft seal should only be repaired after confirming the leak with an electrical leak detector (SST: J-41995).

Always remove any remaining dye from the leak area after repairs are completed to avoid a misdiagnosis
during a future service.

Never allow dye to come into contact with painted body panels or interior components. If dye is spilled,
clean immediately with the approved dye cleaner. Fluorescent dye left on a surface for an extended period
of time cannot be removed.

Never spray the fluorescent dye cleaning agent on hot surfaces (engine exhaust manifold, etc.).

Never use more than one refrigerant dye bottle (1/4 ounce /7.4 cc) per A/C system.

Leak detection dyes for HFC-134a (R-134a) and CFC-12 (R-12) A/C systems are different. Never use
HFC-134a (R-134a) leak detection dye in CFC-12 (R-12) A/C system, or CFC-12 (R-12) leak detection
dye in HFC-134a (R-134a) A/C system, or A/C system damage may result.

The fluorescent properties of the dye will remain for three years or a little over unless a compressor mal-
function occurs.
IDENTIFICATION
NOTE:
Vehicles with factory installed fluorescent dye have a green label.
Vehicles without factory installed fluorescent dye have a blue label.
IDENTIFICATION LABEL FOR VEHICLE
Vehicles with factory installed fluorescent dye have the identification label on the front side of hood.

REFRIGERATION SYSTEM
ATC-25
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2007 April2007 M35/M45
Component LayoutNJS000G2
SJIA1785E