2006 SUZUKI SX4 Service Workshop Manual

Downloaded from www.Manualslib.com manuals search engine Manual Transmission/Transaxle: 5B-13
Gear Shift and Select Shaft Assembly ComponentsS6RW0D5206011
1
10
3
4
9
2
6
12
7
11
5
8(a)
(a)
(a)
(a)1217G
1217G
1217G
A13
I6RW0C520001-01
1. Gear shift & select shaft 7. Gear shift guide case bolt No.1
: Apply sealant 99000-31260 to bolt thread.13. Oil seal
: Apply grease 99000-25011 to oil seal lip.
2. 5th & reverse gear shift cam 8. Gear shift guide case bolt No.2 : 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
3. Gear shift interlock plate 9. 5th to reverse interlock guide bolt
: Apply sealant 99000-31260 to bolt thread.: Do not reuse.
4. Gear shift & select lever 10. Gear shift interlock bolt
: Apply sealant 99000-31260 to bolt thread.: Apply transaxle oil.
5. Shift cable lever 11. Guide case
6. Select cable lever 12. Select lever bush

Downloaded from www.Manualslib.com manuals search engine 5B-14 Manual Transmission/Transaxle:
Gear Shift and Select Shaft Assembly Removal
and Installation
S6RW0D5206012
Removal
1) Remove battery and tray with ECM.
2) Disconnect gear shift and gear select control cables
from transaxle.
3) Remove gear shift interlock bolt (1) and 5th to
reverse interlock guide bolt (2) from transaxle case.
4) Remove gear shift & select shaft assembly (3).
Installation
1) Clean mating surface of guide case (1) and left case
(5), apply sealant to left case as shown in figure by
such amount that its section is 1.5 mm (0.059 in.) in
diameter, mate guide case with left case.
“B”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
2) Install guide case bolts No.1 to which sealant has
been applied and guide case bolts No.2 (2), and
tighten them to specified torque.
: Sealant 99000–31260 (SUZUKI Bond No.1217G)
Tightening torque
Guide case bolt No.1: 23 N·m (2.3 kgf-m, 17.0 lb-
ft)
Guide case bolt No.2 (a): 23 N·m (2.3 kgf-m, 17.0
lb-ft)3) Install washer and gear shift interlock bolt (3) to
which sealant has been applied and then tighten it to
specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Gear shift interlock bolt (b): 23 N·m (2.3 kgf-m,
17.0 lb-ft)
4) Install washer and 5th to reverse interlock guide bolt
(4) to which sealant has been applied and then
tighten it to specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
5th to reverse interlock guide bolt (c): 23 N·m (
2.3 kgf-m, 17.0 lb-ft)
5) Connect gear shift and gear select control cables to
transaxle.
6) Install battery and tray with ECM.
7) Check input shaft for rotation in each gear position.
4. Transaxle side cover
3
1
2
4
I5RW0A520016-01
I5RW0A520017-02

Downloaded from www.Manualslib.com manuals search engine Manual Transmission/Transaxle: 5B-15
Gear Shift and Select Shaft Assembly
Disassembly and Reassembly
S6RW0D5206013
1) Push spring pins out using 2.8 – 3.0 mm (0.11 – 0.12
in.) commercially available spring pin remover and
specified spring pin removers as shown bellow.
Special tool
(A): 09922–85811 4.5 mm
(B): 09925–78210 6.0 mm
2) Inspect component parts for wear, distortion or
damage. If any detect is found, replace detective
part with new one.
NOTE
• When driving in spring pins, prevent shaft
from being bent by supporting it with wood
block.
• Assemble 5th & reverse gear shift cam
with its pit and spring pin aligned.
• Make sure to select an appropriate spring
by identifying the painted colors to keep
gear shifting performance as designed.
– Low speed select spring - Light blue
– Reverse select spring - Pink

1. E-ring 8. Spring pin
2. Washer 9. Gear shift & select shaft
3. Reverse select spring 10. 5th & reverse gear shift cam
4. Gear shift interlock plate 11. Cam guide return spring
5. Ball 12. 5th & reverse gear shift cam guide
6. Gear shift interlock spring 13. Low speed select spring
7. Gear shift & select lever 14. Spring pin remover
I6RW0C520002-01

Downloaded from www.Manualslib.com manuals search engine 5B-16 Manual Transmission/Transaxle:
Manual Transaxle Assembly ComponentsS6RW0D5206014
I5RW0A520018-03
1. Transaxle right case 22. Shift fork bolt
: Apply thread lock 99000-32110 to all around thread part of bolt.
2. Transaxle left case
: Apply sealant 99000-31260 to mating surface of left case and right
case.23. 5th gear shift fork
3. Gear shift and select shaft assembly
: Apply sealant 99000-31260 to mating surface of guide case and left
case.24. Needle bearing
4. Transaxle left case plate 25. Input shaft 5th gear
5. Transaxle side cover
: Apply sealant 99000-31260 to mating surface of side cover and left
case.26. Reverse gear shift lever
6. Back up light switch 27. Reverse gear shift lever bolt
: Apply thread lock 99000-32110 to all around thread part of bolt.
7. O-ring28. Reverse gear shaft
8. Differential assembly 29. Washer
9. Oil level / filler plug
: Apply sealant 99000-31260 to all around thread part of plug.30. Reverse idler gear

Downloaded from www.Manualslib.com manuals search engine Manual Transmission/Transaxle: 5B-17
Fifth Gear Disassembly and ReassemblyS6RW0D5206015
Disassembly
1) Remove cover bolts and take off transaxle side
cover.
CAUTION!
Care should be taken not to distort side cover
when it is removed from left case.

2) Using special tool, remove circlip (1).
Special tool
: 09900–06107
3) Remove shift fork shaft bolt (2).
4) Remove gear shift fork (3) and 5th gear all together.
Use gear puller for removal if spline fitting of hub is
tight.5) Unfasten caulking of countershaft nut (2), install
input shaft 5th gear (1) and special tool to stop
rotation of shafts, and then remove countershaft nut
(2).
Special tool
(A): 09927–76060
6) Remove input shaft 5th gear, needle bearing and
then countershaft 5th gear (1). Gear puller (2) would
be necessary if spline fitting of countershaft 5th gear
is tight.
10. Oil drain plug
: Apply sealant 99000-31260 to all around thread part of plug.31. Reverse shaft bolt
: Apply sealant 99000-31260 to thread part of bolt.
11. Oil gutter bolt
: Apply thread lock 99000-32110 to all around thread part of bolt.32. Washer
12. Left case plate bolt
: Apply thread lock 99000-32110 to all around thread part of bolt.33. Oil seal
: Apply SUZUKI SUPER GREASE A
99000-25010 to Oil seal lip.
13. Side cover bolts 34. Outer race
14. Transaxle case bolts 35. Shim
15. 5th speed synchronizer ring 36. Oil gutter
16. 5th speed synchronizer lever : 21 N⋅m (2.1 kgf-m, 15.5 lb-ft)
17. 5th speed sleeve & hub : 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
18. Circlip: 10 N⋅m (1.0 kgf-m, 7.5 lb-ft)
19. Bearing set shim : 100 N⋅m (10.0 kgf-m, 72.5 lb-ft)
20. Countershaft 5th gear : Do not reuse.
21. Countershaft nut
: After tightening nut to specified torque, caulk nut securely.: Apply transaxle oil.
32
1
I4RH01520015-01
(A)
2
1
I4RH01520016-01
I4RH01520017-01

Downloaded from www.Manualslib.com manuals search engine 5B-18 Manual Transmission/Transaxle:
Reassembly
1) Install countershaft 5th gear (1) to countershaft
facing machined boss “A” inward.
2) Apply transaxle oil to needle bearing, and install it to
input shaft.
3) Install input shaft 5th gear (1) to input shaft.
4) Install special tool in order to stop shaft rotation.
Special tool
(A): 09927–76060
5) Tighten new countershaft nut (2) to specified torque,
and caulk nut securely.
Tightening torque
Countershaft nut (a): 100 N·m (10.0 kgf-m, 75.0
lb-ft)
6) Assemble 5th speed synchronizer sleeve (1), hub
(2), 5th speed synchronizer levers (3) and
synchronizer ring (4) as follows.a) Install hub (1) to 5th speed synchronizer sleeve
(2) in specified direction as shown in figure.
b) Fit 5th speed synchronizer levers (1) to hub (2) in
specified position as shown in figure.
NOTE
Align protrusion “A” of 5th speed
synchronizer levers (1) with groove of hub
(2).

c) Install synchronizer ring (1) to hub (2) in
specified direction as shown in figure.
A: Machined boss (Inside)
B: No machining (Outside)
I2RH01520088-01
(A)
2, (a)
1
I4RH01520047-01
I4RH01520054-01
A: Chamfered side
B: Long boss
1
2 B
A
I4RH01520048-01
1A
2 A
I4RH01520049-01
1
2
I4RH01520055-01

Downloaded from www.Manualslib.com manuals search engine Manual Transmission/Transaxle: 5B-19
7) Fit 5th gear shift fork (1) to sleeve (3) and hub (2)
assembly, and install them into input shaft and gear
shift shaft, aligning punch mark (4) with matching
mark (5) on input shaft.
8) Tighten shift fork shaft bolt (2) to which thread lock
cement has been applied.
“A”: Thread lock cement 99000–32110 (Thread
Lock Cement Super 1322)
Tightening torque
Shift fork shaft bolt (a): 10 N·m (1.0 kgf-m, 7.5 lb-
ft)
9) Using special tool, install new circlip (1) to input shaft
(3).
Special tool
: 09900–0610710) Clean mating surface of both left case and side
cover (1), apply sealant to side cover as shown in
figure by such amount that its section is 1.5 mm
(0.059 in.) in diameter, mate it with left case, and
then tighten side cover bolts with specified torque.
“B”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Side cover bolt (a): 10 N·m (1.0 kgf-m, 7.5 lb-ft)
Manual Transaxle Assembly Disassembly and
Reassembly
S6RW0D5206016
Disassembly
1) Remove left case plate bolts (1), and take off left
case plate (2).
I3RH0A520080-01
2, (a), “A”
13
I5RW0A520019-013. Input shaft
I5RW0A520020-01
I4RH01520018-01

Downloaded from www.Manualslib.com manuals search engine 5B-20 Manual Transmission/Transaxle:
2) Remove bearing set shim.
3) Remove snap ring (1) using special tool.
Special tool
(A): 09900–06107
4) Remove gear shift locating bolts (1), then take out
locating springs and steel balls.
5) Remove reverse shaft bolt (2) with washer.
6) Remove transaxle case bolts (1) from outside and
another bolts from clutch housing side.
7) Tapping left case flanges with plastic hammer,
remove left case.8) Pull out reverse gear shaft (1) with washer (2), then
take off reverse idler gear (3).
9) Remove reverse gear shift lever bolts (4) and
reverse gear shift lever (5).
10) Pull out 5th & reverse gear shift guide shaft (6)
together with 5th & reverse gear shift shaft (7).
NOTE
When removing 5th & reverse gear shift shaft
(7) and guide shaft (6), push up high speed
gear shift shaft and shift it to 4th to facilitate
removal of 5th & reverse shift shaft.

11) Tapping input shaft end with plastic hammer, push it
out as assembly from case a little, then take out
input shaft assembly (1), countershaft assembly (2),
high speed gear shift shaft (3) and low speed gear
shift shaft (4) all at once.
12) Remove countershaft left bearing outer race from left
case.
13) Remove differential assembly from right case.
2. Input shaft
3. Input shaft left bearing
1 (A)
2
3
I4RH01520019-01
1I5RW0A520021-01
I4RH01520020-01
I3RH0A520012-01
I2RH01520035-01