2006 NISSAN VERSA engine

EI-4
PREPARATION
Revision: June 20062007 Versa
PREPARATIONPFP:00002
Special Service ToolsEIS009A8
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service ToolsEIS009A9
Tool number
(Kent-Moore No.)
Tool nameDescription
—
(J-39570)
Chassis earLocating the noise
—
(J-43980)
NISSAN Squeak and Rattle kitRepairing the cause of noise
SBT 8 39
SBT 8 40
Tool number
(Kent-Moore No.)
Tool nameDescription
—
(J-39565)
Engine earLocating the noise
SIIA0995E

EI-6
SQUEAK AND RATTLE TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:

Close a door.

Tap or push/pull around the area where the noise appears to be coming from.

Rev the engine.

Use a floor jack to recreate vehicle “twist”.

At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).

Raise the vehicle on a hoist and hit a tire with a rubber hammer.

Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.

If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear: J-39565 and mechanics stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by:

Removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fasteners
can be broken or lost during the repair, resulting in the creation of new noise.

Tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be elimi-
nated only temporarily.

Feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing
the noise.

Placing a piece of paper between components that you suspect are causing the noise.

Looking for loose components and contact marks.
Refer to EI-7, "
Generic Squeak and Rattle Troubleshooting" .
REPAIR THE CAUSE

If the cause is a loose component, tighten the component securely.

If the cause is insufficient clearance between components:
–Separate components by repositioning or loosening and retightening the component, if possible.
–Insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A NISSAN Squeak and Rattle Kit (J-43980) is available through your authorized NISSAN
Parts Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the NISSAN Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100 x 135 mm (3.94 x 5.31 in)/76884-71L01: 60 x 85 mm (2.36 x 3.35 in)/76884-71L02: 15 x 25
mm (0.59 x 0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.

EI-8
SQUEAK AND RATTLE TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the NISSAN Squeak and Rattle Kit (J-43980) to repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1. Trunk lid bumpers out of adjustment
2. Trunk lid striker out of adjustment
3. The trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sun visor shaft shaking in the holder
3. Front or rear windshield touching headliner and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
OVERHEAD CONSOLE (FRONT AND REAR)
Overhead console noises are often caused by the console panel clips not being engaged correctly. Most of
these incidents are repaired by pushing up on the console at the clip locations until the clips engage.
In addition look for:
1. Loose harness or harness connectors.
2. Front console map/reading lamp lens loose.
3. Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component installed on the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.

EI-14
FRONT BUMPER
Revision: June 20062007 Versa
FRONT BUMPERPFP:F2022
Removal and Installation EIS0096K
1. Bumper stay RH 2. Bumper reinforcement (production) 3. Bumper energy absorber
4. Engine undercover 5. Front valance 6. Front bumper fascia
7. Access cover 8. Fog lamp opening finisher (without
fog lamps)9. Fog lamp opening finisher (with fog
lamps)
10. Fog lamp assembly 11. Bumper side retainer 12. Bumper stay LH (service)
LIIA2562E

FRONT BUMPER
EI-15
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: June 20062007 Versa
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1. Open hood.
2. Remove front grille. Refer to EI-19, "
FRONT GRILLE" .
3. Remove front fender protectors RH/LH. Refer to EI-22, "
FENDER PROTECTOR" .
4. Remove front valance and engine undercover.
5. Remove screws of front bumper fascia RH/LH.
6. Pull the outboard edge of front bumper fascia away from vehicle
to disengage from the bumper side retainer.
7. Disconnect fog lamp harness connector RH/LH (if equipped).
8. Remove the front bumper fascia.
9. Remove fog lamp opening finisher and fog lamp assembly RH/
LH (if equipped). Refer to LT-50, "
Removal and Installation" .
10. Remove bumper energy absorber.
11. Remove RH/LH air guide mounting clips of bumper reinforcement.
12. Remove the nuts, then remove bumper reinforcement and bumper stay(s):

For production, bumper stay LH is part of bumper reinforcement.

For service, bumper stay RH/LH are separate assemblies.
13. Remove bumper side bracket RH/LH after front bumper fascia removal.
PIIB2537J
PIIB2538J
PIIB2543J

EM-1
ENGINE MECHANICAL
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EM
A
EM
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover ..... 3
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 3
OPERATION PROCEDURE ................................. 3
Precautions for Drain Coolant .................................. 4
Precautions for Disconnecting Fuel Piping .............. 4
Precautions for Removal and Disassembly ............. 4
Precautions for Inspection, Repair and Replace-
ment ......................................................................... 4
Precautions for Assembly and Installation ............... 4
Parts Requiring Angular Tightening ......................... 4
Precautions for Liquid Gasket .................................. 5
REMOVAL OF LIQUID GASKET SEALING .......... 5
LIQUID GASKET APPLICATION PROCEDURE ..... 5
PREPARATION ........................................................... 7
Special Service Tools ............................................... 7
Commercial Service Tools ........................................ 9
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ...............................................11
NVH Troubleshooting — Engine Noise ...................11
Use the Chart Below to Help You Find the Cause
of the Symptom. ..................................................... 12
DRIVE BELTS ........................................................... 13
Components ........................................................... 13
Checking Drive Belts .............................................. 13
Tension Adjustment ................................................ 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
Components ........................................................... 14
Removal and Installation of Drive Belt Auto-Ten-
sioner ..................................................................... 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 15
AIR CLEANER AND AIR DUCT ............................... 16Components ........................................................... 16
Removal and Installation ........................................ 16
REMOVAL ........................................................... 16
INSTALLATION ................................................... 16
Changing Air Cleaner Filter .................................... 17
REMOVAL ........................................................... 17
INSPECTION AFTER REMOVAL ....................... 17
INSTALLATION ................................................... 17
INTAKE MANIFOLD ................................................. 18
Components ........................................................... 18
Removal and Installation ........................................ 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 19
INSPECTION AFTER INSTALLATION ................ 20
EXHAUST MANIFOLD ............................................. 21
Components ........................................................... 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21
INSPECTION AFTER REMOVAL ....................... 22
INSTALLATION ................................................... 22
OIL PAN .................................................................... 24
Components ........................................................... 24
Removal and Installation ........................................ 24
REMOVAL ........................................................... 24
INSPECTION AFTER REMOVAL ....................... 26
INSTALLATION ................................................... 26
IGNITION COIL, SPARK PLUG AND ROCKER
COVER ...................................................................... 30
Components ........................................................... 30
Removal and Installation ........................................ 30
REMOVAL ........................................................... 30
INSPECTION AFTER REMOVAL ....................... 31
INSTALLATION ................................................... 31
FUEL INJECTOR AND FUEL TUBE ........................ 33
Components ........................................................... 33
Removal and Installation ........................................ 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 35
TIMING CHAIN .......................................................... 37

EM-2Revision: June 20062007 Versa Components ........................................................... 37
Removal and Installation ........................................ 38
REMOVAL ........................................................... 38
INSPECTION AFTER REMOVAL ........................ 41
INSTALLATION .................................................... 42
CAMSHAFT ............................................................... 47
Components ........................................................... 47
Removal and Installation ........................................ 47
REMOVAL ........................................................... 47
INSPECTION AFTER REMOVAL ........................ 49
INSTALLATION .................................................... 51
INSPECTION AFTER INSTALLATION ................ 54
Valve Clearance ...................................................... 55
INSPECTION ....................................................... 55
ADJUSTMENT .................................................... 57
OIL SEAL .................................................................. 59
Removal and Installation of Valve Oil Seal ............. 59
REMOVAL ........................................................... 59
INSTALLATION .................................................... 59
Removal and Installation of Front Oil Seal ............. 60
REMOVAL ........................................................... 60
INSTALLATION .................................................... 60
Removal and Installation of Rear Oil Seal .............. 61
REMOVAL ........................................................... 61
INSTALLATION .................................................... 61
CYLINDER HEAD ..................................................... 62
On-Vehicle Service ................................................. 62
CHECKING COMPRESSION PRESSURE ......... 62
Components ........................................................... 63
Removal and Installation ........................................ 63
REMOVAL ........................................................... 63
INSPECTION AFTER REMOVAL ........................ 64
INSTALLATION .................................................... 65
Components ........................................................... 66
Disassembly and Assembly .................................... 66
DISASSEMBLY ................................................... 66
ASSEMBLY ......................................................... 67
Inspection After Disassembly ................................. 68
VALVE DIMENSIONS .......................................... 68
VALVE GUIDE CLEARANCE .............................. 68
VALVE GUIDE REPLACEMENT ......................... 69
VALVE SEAT CONTACT ..................................... 70
VALVE SEAT REPLACEMENT ........................... 70
VALVE SPRING SQUARENESS ......................... 71
VALVE SPRING DIMENSIONS AND VALVE
SPRING PRESSURE LOAD ............................... 72
ENGINE ASSEMBLY ................................................ 73
Components ........................................................... 73
Removal and Installation ........................................ 73
REMOVAL ........................................................... 74
INSTALLATION .................................................... 76
INSPECTION AFTER INSTALLATION ................ 76
CYLINDER BLOCK ................................................... 77
Components ........................................................... 77
Disassembly and Assembly .................................... 78
DISASSEMBLY ................................................... 78ASSEMBLY ..........................................................81
How to Select Piston and Bearing ..........................87
DESCRIPTION ....................................................87
HOW TO SELECT PISTON .................................87
HOW TO SELECT CONNECTING ROD BEAR-
ING .......................................................................88
HOW TO SELECT MAIN BEARING ....................91
Inspection After Disassembly ..................................95
CRANKSHAFT END PLAY ..................................95
CONNECTING ROD SIDE CLEARANCE ...........95
PISTON TO PISTON PIN OIL CLEARANCE .......95
PISTON RING SIDE CLEARANCE .....................96
PISTON RING END GAP ....................................96
CONNECTING ROD BEND AND TORSION .......97
CONNECTING ROD BIG END DIAMETER ........97
CONNECTING ROD BUSHING OIL CLEAR-
ANCE ...................................................................97
CYLINDER BLOCK TOP SURFACE DISTOR-
TION ....................................................................98
MAIN BEARING HOUSING INNER DIAMETER ...98
PISTON TO CYLINDER BORE CLEARANCE ....99
CRANKSHAFT MAIN JOURNAL DIAMETER ... 100
CRANKSHAFT PIN JOURNAL DIAMETER ...... 100
OUT-OF-ROUND AND TAPER OF CRANK-
SHAFT ............................................................... 100
CRANKSHAFT RUNOUT .................................. 100
CONNECTING ROD BEARING OIL CLEAR-
ANCE ................................................................. 101
MAIN BEARING OIL CLEARANCE ................... 101
MAIN BEARING CRUSH HEIGHT .................... 102
CONNECTING ROD BEARING CRUSH
HEIGHT ............................................................. 102
MAIN BEARING CAP BOLT OUTER DIAMETER . 103
CONNECTING ROD BOLT OUTER DIAMETER . 103
CLOGGED OR DAMAGED OIL FILTER (FOR
INTAKE VALVE TIMING CONTROL) ................. 103
FLYWHEEL DEFLECTION (M/T MODELS) ...... 103
MOVEMENT AMOUNT OF FLYWHEEL (M/T
MODELS) ........................................................... 103
SERVICE DATA AND SPECIFICATIONS (SDS) .... 105
Standard and Limit ................................................ 105
GENERAL SPECIFICATIONS ........................... 105
DRIVE BELT ...................................................... 105
WATER CONTROL VALVE ................................ 105
EXHAUST MANIFOLD ...................................... 105
THERMOSTAT ................................................... 105
SPARK PLUG .................................................... 105
CYLINDER HEAD .............................................. 105
VALVE ................................................................ 106
CAMSHAFT AND CAMSHAFT BEARING ......... 109
CYLINDER BLOCK ............................................110
PISTON, PISTON RING AND PISTON PIN ...... 111
CONNECTING ROD ..........................................112
CRANKSHAFT ...................................................112
MAIN BEARING .................................................114
CONNECTING ROD BEARING .........................114

EM-4Revision: June 2006
PRECAUTIONS
2007 Versa
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.
Precautions for Drain CoolantEBS00U6S

Drain coolant when engine is cooled.
Precautions for Disconnecting Fuel PipingEBS00U6T

Before starting work, make sure no fire or spark producing items are in the work area.

Release fuel pressure before disassembly.

After disconnecting pipes, plug openings to stop fuel leakage.
Precautions for Removal and DisassemblyEBS00U6U

When instructed to use special service tools, use the specified tools. Always be careful to work safely,
avoid forceful or uninstructed operations.

Exercise maximum care to avoid damage to mating or sliding surfaces.

Cover openings of engine system with tape or the equivalent, if necessary, to seal out foreign materials.

Mark and arrange disassembly parts in an organized way for easy troubleshooting and assembly.

When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified. Power tools may be
used where noted in the step.
Precautions for Inspection, Repair and ReplacementEBS00U6V

Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way,
and replace if necessary.
Precautions for Assembly and InstallationEBS00U6W

Use torque wrench to tighten bolts or nuts to specification.

When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is speci-
fied, do exactly as specified.

Replace with new gasket, packing, oil seal or O-ring.

Thoroughly wash, clean, and air-blow each part. Carefully check oil or coolant passages for any restriction
and blockage.

Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.

Release air within route after draining coolant.

Before starting engine, apply fuel pressure to fuel lines with turning ignition switch ON (with engine
stopped). Then make sure that there are no leaks at fuel line connections.

After repairing, start engine and increase engine speed to check coolant, fuel, oil, and exhaust systems
for leakage.
Parts Requiring Angular TighteningEBS00U6X

Use an angle wrench for the final tightening of the following engine parts:
–Cylinder head bolts
–Camshaft sprocket (INT)
–Main bearing cap bolts
–Connecting rod cap nuts
–Crankshaft pulley bolt (No angle wrench is required as the bolt flange is provided with notches for angular
tightening)
Tool number : KV10112100 (BT-8653-A)