2006 ACURA CSX airbag off


(#' 
'
-)
µ
µ
µ
µ
DTC 33-1x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO YES
NO
24-106SRS
DTC Troubleshooting (cont’d)
B
070AZ-SNAA300 07SAZ-TB4011A
A
Open in the Left Side Curtain Airbag Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the left side curtain airbag 2P connector
(A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).
Go to step 9.
Open in the left side curtain airbag; replace
the left side curtain airbag (see page 24-192), then
clear the DTC.
Does the SRS indicator stay on, and is DT C 33-1x indicated?
Is DTC 33-1x indicated?
08/08/21 13:58:21 61SNR030_240_0106
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ µ
µ
YES
NO Special Tools Required
YES
NO
DTC 33-3x (‘‘x’’ can be 0 thru 9 or A thru F):
24-10724-107
FLOOR WIRE HARNESS
2P CONNECTOR 070AZ-SNAA300 A
9. Turn the ignition switch to LOCK (0). Disconnect thenegative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner connectors (see step 8 on page 24-21) and both
seat belt tensioner connectors (see step 7 on page
24-21).
11. Disconnect SRS unit connector B (28P) from the SRS unit (see step 9 on page 24-21).
12. Disconnect the SRS inflator simulator from the SRS simulator lead. Do not disconnect the simulator
lead from the floor wire harness 2P connector.
13. Measure the resistance between the terminals of the black SRS simulator lead (A). There should be
less than 1.0 .
Faulty SRS unit or poor connection at the
SRS unit connector B (28P) and the SRS unit. Check
the connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Open in the harness; replace the floor wire
harness, then clear the DTC.  SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
 SRS short canceller 070AZ-SAA0100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
(cont’d)
Short to Another Wire or Decreased
Resistance in the Left Side Curtain Airbag
Inflator
Is the resistance as specif ied? Does the SRS indicator stay on, and is DT C 33-3x
indicated?
08/08/21 13:58:21 61SNR030_240_0107
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 33-8x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-109
A
070AZ-SNAA300 07SAZ-TB4011A
B
Short to Power in the Left Side Curtain
Airbag Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the left side curtain airbag 2P connector
(A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
(cont’d)
Does the SRS indicator stay on, and is DT C 33-8xindicated?
08/08/21 13:58:22 61SNR030_240_0109
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 33-9x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-111
A
070AZ-SNAA300 07SAZ-TB4011A
B
Short to Ground in the Left Side Curtain
Airbag Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the left side curtain airbag 2P connector
(A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
(cont’d)
Does the SRS indicator stay on, and is DT C 33-9xindicated?
08/08/21 13:58:22 61SNR030_240_0111
ProCarManuals.com
DYNOMITE -2009-


(#' 
'
-)
µ
µ
DTC 34-1x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-113
A 070AZ-SNAA300
07SAZ-TB4011A
B
Open in the Right Side Curtain Airbag Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the right side curtain airbag 2P
connector (A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
(cont’d)
Does t he SRS i nd i cat or st ay on, and i s DT C 34-1xindicated?
08/08/21 13:58:23 61SNR030_240_0113
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
DTC 34-3x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO
24-115
A 070AZ-SNAA300
07SAZ-TB4011A
B
Short to Another Wire or Decreased
Resistance in the Right Side Curtain Airbag
Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
 SRS short canceller 070AZ-SAA0100
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the right side curtain airbag 2P
connector (A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
(cont’d)
Does t he SRS i nd i cat or st ay on, and i s DT C 34-3xindicated?
08/08/21 13:58:23 61SNR030_240_0115
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ
µ
µ
DTC 34-8x (‘‘x’’ can be 0 thru 9 or A thru F):
Special Tools Required
YES
NO YES
NO
24-117
A
070AZ-SNAA300
07SAZ-TB4011A
B
Short to Power in the Right Side Curtain
Airbag Inflator
 SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes. 4. Remove the headliner (see page 20-84), then
disconnect the right side curtain airbag 2P
connector (A) from the floor wire harness (B).
5. Connect the SRS inflator simulator (2 connector) and simulator lead L to the floor wire harness.
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22).
Go to step 9.
Short to power in the right side curtain airbag
inflator; replace the right side curtain airbag
(see page 24-192), then clear the DTC.
(cont’d)
Does t he SRS i nd i cat or st ay on, and i s DT C 34-8xindicated?
Is DTC 34-8x indicated?
08/08/21 13:58:24 61SNR030_240_0117
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)

µ
µ µ
µ
YES
NO Special Tools Required
YES
NO
DTC 34-9x (‘‘x’’ can be 0 thru 9 or A thru F):
24-11824-118SRS
DTC Troubleshooting (cont’d)
FLOOR WIRE HARNESS
2P CONNECTOR
070AZ-SNAA300 A
9. Turn the ignition switch to LOCK (0). Disconnect thenegative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner connectors (see step 8 on page 24-21) and both
seat belt tensioner connectors (see step 7 on page
24-21).
11. Disconnect SRS unit connector B (28P) from the SRS unit (see step 9 on page 24-21).
12. Disconnect the SRS inflator simulator from the SRS simulator lead. Do not disconnect the simulator
lead from the floor wire harness 2P connector.
13. Reconnect the negative cable to the battery.
14. Turn the ignition switch to ON (II).
15. Measure the voltage between each terminal of the black SRS simulator lead (A) and body ground.
There should be less than 0.2 V.
Faulty SRS unit or poor connection at SRS
unit connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Short to power in the floor wire harness;
replace the floor wire harness, then clear the
DTC.  SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNAA300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
Short to Ground in the Right Side Curtain
Airbag Inflator
Is the voltage as specif ied? Does t he SRS i nd i cat or st ay on, and i s DT C 34-9x
indicated?
08/08/21 13:58:24 61SNR030_240_0118
ProCarManuals.com
DYNOMITE -2009-