2006 ACURA CSX airbag off


24-195
A
2. Connect the side curtain airbag 2P connector (A) to the floor wire harness.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTCs (see page 24-23).
5. After installing the side curtain airbag, confirm proper system operation: Turn the ignition switch to ON (II); theSRS indicator should come on for about 6 seconds and then go off.
6. Install all removed parts.
7. Confirm proper headliner/pillar trim overlap (see page 24-187).
Left side shown; right side is similar.
08/08/21 14:01:57 61SNR030_240_0195
ProCarManuals.com
DYNOMITE -2009-


Î
Î
Seat Belt Tensioner
Seat Belt Buckle Tensioner
24-197
A
A A
A
30 ft
(10 m) 07HAZ-SG00500
A 30 ft
(10 m)
07HAZ-SG00500
8. Disconnect the floor wire harness 4P connector (A) from the seat belt tensioner. Pull the seat belt out
all the way and cut it.
9. Disconnect the floor wire harness 2P connector (A) from the seat belt buckle tensioner. 10. Cut off each connector, and strip the ends of the
wires. Twist each pair of unlike colored wires
together, and clip an alligator clips (A) from the
deployment tool to each pair.
NOTE: Place the deployment tool at least 30 ft (10 m) away from the vehicle.
 The driver’s and front passenger’s airbags have dual inflators. Twist each pair of unlike colored
wires together, and clip an alligator clip to each
pair.
(cont’d)
08/08/21 14:01:59 61SNR030_240_0197
ProCarManuals.com
DYNOMITE -2009-



24-202SRS
Cable Reel Replacement (cont’d)
A
D
B
A C A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
5. Install the steering column covers.
6. If necessary, center the cable reel (new
replacement cable reels come centered). Do this by
first rotating the cable reel clockwise until it stops.
Then rotate it counterclockwise (about three turns)
until the arrow mark (A) on the cable reel label
points straight up.
7. Position the two tabs (A) of the turn signal canceling sleeve (B) as shown, and install the
steering wheel on to the steering column shaft,
making sure the steering wheel hub (C) engages
the pins (D) of the cable reel and tabs of the turn
signal canceling sleeve. Do not tap on the steering
wheel or steering column shaft when installing the
steering wheel. 8. Install a new steering wheel bolt (A), then
reconnect the connectors.
9. Install the driver’s airbag (see page 24-188).
10. Do the battery terminal reconnection procedure (see page 22-68).
11. Clear any DTCs (see page 24-23).
12. After installing the cable reel, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 After the SRS indicator has turned off, turn the steering wheel fully left and right to confirm the
SRS indicator does not come on.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel switches work properly.
Replace.
08/08/21 14:02:00 61SNR030_240_0202
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
24-212SRS
Passenger’s Airbag Cutoff Indicator Illumination Bulb Test/Replacement
B
A
C
1. Remove the center panel: Navigation unit, with navigation system.– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
 Audio unit, without navigation system. – ’06-08 models (see page 23-80)
– ’09 model (see page 23-155)
2. Remove the screws (A) and the passenger’s airbag cutoff indicator (B) from the center panel.
3. Check for continuity between the No. 2 and No. 3 terminals of the indicator. If there is no continuity,
replace the bulb (C).
4. Reinstall the parts in the reverse order of removal.
08/08/21 14:02:11 61SNR030_240_0212
ProCarManuals.com
DYNOMITE -2009-