2006 ACURA CSX airbag off


(#' 
'
-)
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
DTC 92-1x (‘‘x’’ can be 0 thru 9 or A thru F):
24-16924-169
A
B
3. Check the connection at the OPDS sensor harness
connectors (A) and the ODS unit harness 18P
connector (B).
Go to step 4.
Repair the poor connection, then clear the
DTC.
4. Replace the OPDS sensor/seat-back foam (see page 20-123), and initialize the ODS unit (see page 24-26),
then clear the DTC.
5. Clear the DTC memory, then check for DTC 86-1x or 86-2x.
Replace the ODS unit (see page 24-209), then
clear the DTC.
The system is OK. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least
3 minutes.
4. Disconnect the passenger’s airbag cutoff indicator 4P connector (see page 24-212).
(cont’d)
Open in the Passenger’s Airbag Cutoff
Indicator
I s t he connect i on OK ?Is DT C 86-1x or 86-2x indicated? Does the SRS indicator stay on, and is DT C 92-1x
indicated?
08/08/21 14:00:55 61SNR030_240_0169
ProCarManuals.com
DYNOMITE -2009-


(#' 
'-)
µ
µ µ
µ
YES
NO YES
NO
DTC 92-2x (‘‘x’’ can be 0 thru 9 or A thru F):
24-17024-170SRS
DTC Troubleshooting (cont’d)
SRS UNIT CONNECTOR A (28P)
5. Disconnect SRS unit connector A (28P) from the
SRS unit (see step 9 on page 24-21).
6. Reconnect the negative cable to the battery.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between SRS unit connector A (28P) terminal No. 13 and body ground. There
should be less than 0.2 V.
Faulty SRS unit or passenger’s airbag cutoff
indicator; replace the passenger’s airbag cutoff
indicator (see page 24-212), then clear the DTC. If
the problem is still present, replace the SRS unit
(see page 24-203).
Short to power in the dashboard wire
harness; replace the dashboard wire harness, then
clear the DTC. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least
3 minutes.
4. Disconnect the passenger’s airbag cutoff indicator 4P connector (see page 24-212).
5. Disconnect SRS unit connector A (28P) from the SRS unit (see page 24-21).
Open or Short to Ground in the Passenger’s
Airbag Cutoff Indicator
Wire side of female terminals
Is the voltage as specif ied? Does the SRS indicator stay on, and DT C 92-2x
indicated?
08/08/21 14:00:55 61SNR030_240_0170
ProCarManuals.com
DYNOMITE -2009-



(#' 
'

-)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
DTC A1-1x (‘‘x’’ can be 0 thru 9 or A thru F):
24-17124-171
SRS UNIT CONNECTOR A (28P)
PASSENGER’S AIRBAG CUTOFF
INDICATOR 4P CONNECTOR BLU
SRS UNIT CONNECTOR A (28P)
6. Measure the resistance between SRS unitconnector A (28P) terminal No. 13 and passenger’s
airbag cutoff indicator 4P connector terminal No. 4.
There should be less than 1.0 .
Go to step 7.
Open in the dashboard wire harness; replace
the dashboard wire harness, then clear the DTC.
7. Measure the resistance between SRS unit connector A (28P) terminal No. 13 body ground.
There should be an open circuit or at least 1 M .
Check for a faulty SRS unit or passenger’s
airbag cutoff indicator; replace the passenger’s
airbag cutoff indicator (see page 24-212), then clear
the DTC. If the problem is still present, replace the
SRS unit (see page 24-203).
Short to ground in the dashboard wire
harness; replace the dashboard wire harness, then
clear the DTC. NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and wait for 10 seconds.
3. Read the DTC (see page 24-22).
Go to step 4.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
4. Turn the ignition switch to LOCK (0).
5. Check the No. 9 (7.5 A) fuse in the under-dash fuse/ relay box.
Go to step 6.
Replace the fuse, then turn the ignition switch
to ON (II). If the fuse blows again, check for a short
in the No. 9 (7.5 A) fuse circuit (dashboard wire
harness, floor wire harness, front passenger’s seat
wire harness (with seat heater), or ODS unit
harness), then clear the DTC.
6. Disconnect the negative cable from the battery, then wait at least 3 minutes.
7. Disconnect the SRS unit connector A (28P) from the SRS unit (see step 9 on page 24-21).
8. Reconnect the negative cable to the battery.
9. Turn the ignition switch to ON (II).
(cont’d)
Faulty Power supply (VA Line)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the resistance as specif ied?
Is the resistance as specif ied? I s DT C A1-1x i nd i cat ed ?
IsthefuseOK?
08/08/21 14:00:56 61SNR030_240_0171
ProCarManuals.com
DYNOMITE -2009-

(#')(#')
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Side airbag cutoff indicator stays on Side airbag cutoff indicator does not come
on
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
24-18324-183
1. Make sure nothing is on the front passenger’s seat.
2. Make sure the seat back is dry.
3. Turn the ignition switch to ON (II), and see if the
indicator come on.
Go to the Symptom Troubleshooting ‘‘SRS
indicator stays on, but no DTCs are stored.’’
Go to step 2.
4. Connect the HDS to the data link connector (DLC) (see page 24-22).
5. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not troubleshoot the
DLC circuit (see page 11-204).
6. Select Body Electrical Status with the HDS.
7. Check for DTCs in the Gauge Menu with the HDS.
Go to the DTC B1187 troubleshooting
(see page 22-265).
Go to step 8.
8. Do the gauge control module self-diagnostic function (see page 22-241).
Initialize the ODS unit (see page 24-26). If the
problem is still present, replace the OPDS sensor/
seat-back (see page 20-123).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22- 277).NOTE: If the SRS indicator also stays on, go to SRS
indicator stays on, but no DTCs are stored (see page
24-182).
1. Turn the ignition switch to LOCK (0), then wait for 10 seconds.
2. Turn the ignition switch to ON (II), and check that the side airbag cutoff indicator comes on for about
6 seconds.
Go to the Symptom Troubleshooting ‘‘SRS
indicator stays on.’’
Go to step 3.
3. Connect the HDS to the data link connector (DLC) (see page 24-22).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not troubleshoot the
DLC circuit (see page 11-204).
5. Do the gauge control module self-diagnostic function (see page 22-241).
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
Does t he SRS i nd i cat or come on and st ay on?
I s DT C B1187 i nd i cat ed ?Does t he si d e ai r bag cut of f i nd i cat or f l ash? Does t he si d e ai r bag cut of f i nd i cat or come on?
Does t he si d e ai r bag cut of f i nd i cat or come on?
08/08/21 14:01:53 61SNR030_240_0183
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ µ
µ
µ
µ
Passenger’s airbag cutoff indicator stays on
or comes on suddenly
YES
NO YES
NO
YES
NO
24-184SRS
Symptom Troubleshooting (cont’d)
NOTE: Under the following conditions, the passenger’s
airbag cutoff indicator stays on or comes on suddenly.
 No one is sitting the front passenger’s seat, but there is an object on the seat more than 5 kg (11 lbs).
 The seat belt is buckled, but no one is sitting on the front passenger’s seat.
 Someone who is less than 30 kg (66 lbs) is sitting on the front passenger’s seat.
 Someone who is more than 30 kg (66 lbs) but is supporting some of their body weight on their legs,
feet, arms, or hands.
1. Check for these items, then recheck the passenger’s airbag cutoff indicator.
 The front passenger’s seat is/was installed correctly.
 Nothing is/was on the front passenger’s seat.
 Nothing is/was under the front passenger’s seat.
 Nothing is/was in the front passenger’s seat-back pocket.
 Whoever was sitting on the passenger’s seat was sitting in the proper sitting position.
Go to step 2.
Troubleshooting is complete.
2. Connect the HDS to the data link connector (DLC) (see page 24-22).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).5. Select the INSPECTION menu on the HDS, then
select AFTER REPLACING FRONT PASSENGER’S
SEAT COMPONENT(S), and follow the prompts.
Go to step 6.
Troubleshooting is complete.
6. Select the INSPECTION menu on the HDS, then select AFTER A VEHICLE COLLISION, and follow
the prompts.
Replace the SRS unit (see page 24-203). If the
problem is still present, replace the ODS unit
(see page 24-209), and then if the problem is still
present, replace the passenger’s weight sensors
(see page 24-207).
Troubleshooting is complete.
Does the passenger’s airbag cutof f indicator stayon? Does t he passenger ’ s ai r bag cut of f i nd i cat or st ay
on?
Does t he passenger ’ s ai r bag cut of f i nd i cat or st ayon?
08/08/21 14:01:53 61SNR030_240_0184
ProCarManuals.com
DYNOMITE -2009-

Î
 
Î
(#'
 )
Removal Installation
24-188SRS
Driver’s Airbag Replacement
A
B
A
B
C
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
B
A B
NOTE: If replacing the driver’s airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced.
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the access panel (A) from the steering wheel, then disconnect the driver’s airbag 4P
connector (B) from the cable reel.
3. Using a TORX T30 bit, remove the two TORX bolts (A) and discard them.
4. Disconnect the horn switch connector (1P), then remove the driver’s airbag (B). 1. Connect the horn switch connector (1P) (A) to the
driver’s airbag.
2. Place the driver’s airbag (B) in the steering wheel, and secure it with new TORX bolts (C).
3. Connect the driver’s airbag 4P connector (A) to the cable reel 4P connector, then install the access
panel (B) on the steering wheel.
4. Do the battery terminal reconnection procedure (see page 22-68).
5. Clear any DTCs (see page 24-23).
6. After installing the airbag, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 Make sure the horn works.
Replace.
08/08/21 14:01:55 61SNR030_240_0188
ProCarManuals.com
DYNOMITE -2009-




Installation
24-190SRS
Front Passenger’s Airbag Replacement (cont’d)
A
A
B
A
B B
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
6. Cut the four parts (A) of the front passenger’s lid (B)as shown, and remove the front passenger’s airbag.
NOTE: Always replace the front passenger’s lid whenever you remove the front passenger’s
airbag from the lid.
 Replace the front passenger’s airbag if the airbag mounting hooks or its housing is damaged.
7. Insert the hooks (A) of the front passenger’s airbag housing into the new front passenger’s lid, then
insert the other hooks (B) into the lid.
NOTE: Make sure there are no objects between the airbag and the front passenger’s lid.
 Make sure the airbag is fully seated, and make sure the front passenger’s lid is not deformed or
damaged after the airbag is in place.
 Do not use tools when detaching the front passenger’s airbag in order to protect it. 1. Place the front passenger’s airbag assembly (A)
into the dashboard. Tighten the front passenger’s
airbag mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector (A) to dashboard wire harness, then reinstall the
glove box and center panel.
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTC (see page 24-23).
5. After installing the airbag, confirm proper system operation: Turn the ignition switch to ON (II); the
SRS indicator should come on for about 6 seconds
andthengooff.
08/08/21 14:01:56 61SNR030_240_0190
ProCarManuals.com
DYNOMITE -2009-


Î
(#'
 )
Removal Installation
24-191
Side Airbag Replacement
AB
A
B
6.3 N·m
(0.64 kgf·m, 4.65 lbf·ft)
NOTE: If replacing the side airbag after deployment,
refer to Component Replacement/Inspection After
Deployment (see page 24-185) for a complete list of
other parts that must also be replaced. 1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the seat assembly (see page 20-118) and seat-back cover (see page 20-123).
3. Remove the mounting screws (A) and the side airbag (B). NOTE:
 If the side airbag lid is secured by tape, remove the tape.
 Do not open the lid of the side airbag cover.
 Use new mounting screws tightened to the specified torque. When you replace a side airbag, make sure
that the seat-back cover is installed properly.
Improper installation may prevent proper
deployment.
 Be sure to install the harness wires so that they are not pinched or interfering with other parts.
1. Place the side airbag on the seat-back frame (A). Install new side airbag mounting screws (B).
2. Install the seat-back cover in the reverse order of removal (see page 20-123).
3. Install the seat assembly (see page 20-118).
4. Move the front seat and the seat-back through their full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Do the battery terminal reconnection procedure (see page 22-68).
6. Clear any DTCs (see page 24-23).
7. After installing the side airbag, confirm proper system operation: Turn the ignition switch to ON
(II); the SRS indicator should come on for about
6 seconds and then go off.
Replace.
08/08/21 14:01:56 61SNR030_240_0191
ProCarManuals.com
DYNOMITE -2009-