2006 ACURA CSX battery

•••
´
´
•••
TerminalnumberWire color Terminal sign Description Signal
19-57
NOTE: Standard battery voltage is about 12 V.
10 LT BLU K-LINE Communication with HDS
12 WHT FL B Detects left-front wheel speed sensor signal
14 YEL RL B Detects left-rear wheel speed sensor signal
15 BLU RR-GND Detects right-rear wheel speed sensor signal
16 YEL GRY IG1 Power source for activating the
system With ignition switch ON (II): about battery
voltage
17 RED CAN-L F-CAN communication circuit
18 PNK FR-GND Detects right-front wheel speed sensor signal
24 BLK GND Ground for the ABS modulator- control unit Continuity to ground
25 BLK MR-GND Ground for the pump motor Continuity to ground
*1: ’06 model
*2: ’07 model
(cont’d)
*1*2
08/08/21 15:02:17 61SNR030_190_0057
ProCarManuals.com
DYNOMITE -2009-

Î(#'
)

´
19-62ABS Components
Circuit Diagram
BATTERY
UNDER-HOOD FUSE/RELAY BOX
1
19
2827
G502
BLK
WHT
RED
WHT
WHT
RED
ABS
INDICATOR
BRAKE SYSTEM
INDICATOR
GAUGE CONTROL
MODULE (TACH)
LT GRNGRN
LT BLUWHT
RED
IGNITION SWITCH
IG1 HOT in ON (II) and START (III) WHT
LT GRN
WHT
RED BLU
WHT BRAKE PEDAL
POSITION SWITCH
Closed: Brake pedal pressed1
2
C1
C2 UNDER-DASH
FUSE/RELAY BOX
No. 4 (7.5 A)
No. 3 (30 A)
No.1(100A) No.2(50A)
No. 3 (30 A)
No. 12 (15 A) F16
B
G401
BRAKE FLUID
LEVEL SWITCH
Closed: Low fluid
1 2
BLK
ORN
H1
D8
3
6
ORN
1
PARKING
BRAKE SWITCH
Closed: Parking
brake applied DATA LINK
CONNECTOR (DLC)D2
YEL*
GRY*
ORN
6
16
4 7 14
IG11
2
08/08/21 15:03:11 61SNR030_190_0062
ProCarManuals.com
DYNOMITE -2009-


´
µ
µ
µ
µ
YES
NO
YES
NO
19-77
ABS MODULATOR-CONTROL UNIT 25P CONNECTORMR B (RED)
9. Reconnect the ABS modulator-control unit 25Pconnector.
10. Turn the ignition switch to ON (II).
11. Clear the DTC with the HDS.
12. Turn the ignition switch to LOCK (0), then turn it to ON (II) again.
13. Check for DTCs with the HDS.
Replace the ABS modulator-control unit
(see page 19-90).
Troubleshooting is complete. 14. Disconnect the ABS modulator-control unit 25P
connector (see step 2 on page 19-90).
15. Measure the voltage between ABS modulator- control unit 25P connector terminal No. 9 and body
ground.
Check for loose terminals in the ABS
modulator-control unit 25P connector. If necessary,
substitute a known-good ABS modulator-control
unit (see page 19-90), and retest.
Repair open in the wire between the No. 3
(30 A) fuse in the under-hood fuse/relay box and
the ABS modulator-control unit.
Wire side of female terminals
I s DT C 5 1-12 i nd i cat ed ?
Is there battery voltage?
08/08/21 15:03:15 61SNR030_190_0077
ProCarManuals.com
DYNOMITE -2009-


(#' 
'

)
´
µ
µ µ
µ
YES
NO YES
NO
DTC 61-01:
DTC 61-21:
DTC 61-22:
DTC 61-23:
19-8119-81
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
FSR B (WHT)
14. Disconnect the ABS modulator-control unit 25Pconnector (see step 2 on page 19-90).
15. Measure the voltage between ABS modulator- control unit 25P connector terminal No. 8 and body
ground.
Check for loose terminals in the ABS
modulator-control unit 25P connector. If necessary,
substitute a known-good ABS modulator-control
unit (see page 19-90), and retest.
Repair open in the wire between the No. 3
(30 A) fuse in the under-hood fuse/relay box and
the ABS modulator-control unit. 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then start the
engine.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for loose terminals at the ABS
modulator-control unit 25P connector. Refer to
intermittent failures troubleshooting (see page
19-50).
5. Check and note BATTERY voltage in the ABS DATA LIST with the HDS.
6. Using a voltmeter, measure and note the voltage between the battery terminals.
NOTE: If the battery voltage is below 9.5 V, check
the battery (see page 22-67), and troubleshoot the
alternator regulator circuit (see page 4-28).
(cont’d)ABS Modulator-control Unit Initial
IG Low Voltage
ABS Modulator-control Unit
Power Source Low Voltage 1
ABS Modulator-control Unit
Power Source Low Voltage 2
ABS Modulator-control Unit
Power Source Low Voltage 3
Wire side of female terminals
I s t her e bat t er y v ol t age? I s DT C 61-01, 61-21, 61-22, or 61-23 i nd i cat ed ?
08/08/21 15:03:16 61SNR030_190_0081
ProCarManuals.com
DYNOMITE -2009-

(#' 
'
)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
DTC 62-21:
19-8219-82ABS Components
DTC Troubleshooting (cont’d)
7. Compare the data list voltage noted in step 5 to the
battery voltage in step 6.
Intermittent failure, the system is OK at this
time. Check for loose terminals at the ABS
modulator-control unit 25P connector. Refer to
intermittent failures troubleshooting (see page
19-50). If the code resets after clearing, replace the
ABS modulator-control unit (see page 19-90).
Check for loose terminals in the ABS
modulator-control unit 25P connector. If necessary,
substitute a known-good ABS modulator-control
unit (see page 19-90), and retest. 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then start the
engine.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Check and note BATTERY voltage in the ABS DATA LIST with the HDS.
6. Using a voltmeter, measure and note the voltage between the battery terminals.
NOTE: If the voltage is above 15.1 V, troubleshoot
the alternator regulator circuit (see page 4-28).
7. Compare the data list voltage noted in step 5 to the battery voltage in step 6.
Intermittent failure, the system is OK at this
time. Check for loose terminals at the ABS
modulator-control unit 25P connector. Refer to
intermittent failures troubleshooting (see page
19-50). If the code resets after clearing, replace the
ABS modulator-control unit (see page 19-90).
Replace the ABS modulator-control unit
(see page 19-90), and retest.ABS Modulator-control Unit IG
High Voltage
Is t he d i f f er ence bet w een t he t w o v ol t age
r ead i ngs l ess t han 3 V ?
Is DT C 62-21 indicated?
Is t he d i f f er ence bet w een t he t w o v ol t ager ead i ngs l ess t han 3 V ?
08/08/21 15:03:16 61SNR030_190_0082
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
ABS indicator and brake system indicator do
not go off
YES
NO
YES
NO YES
NO
YES
NO
19-88ABS Components
Symptom Troubleshooting
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
IG1 (YEL)*
*1: ’06 model
*2: ’07 model (GRY)*
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
IG1 (YEL)*
*1: ’06 model
*2: ’07 model (GRY)*
1
2
12
1. Turn the ignition switch to LOCK (0).
2. Check the No. 4 (7.5 A) fuse in the under-dash fuse/ relay box.
Go to step 3.
Reinstall the checked fuse, then go to step 8.
3. Disconnect the ABS modulator-control unit 25P connector (see step 2 on page 19-90).
4. Check for continuity between ABS modulator- control unit 25P connector terminal No. 16 and
body ground.
Repair short to body ground in the wire
between the No. 4 (7.5 A) fuse in the under-dash
fuse/relay box and the ABS modulator-control
unit.
Install a new No. 4 (7.5 A) fuse in the under-
dashfuse/relaybox,thengotostep5. 5. Reconnect the ABS modulator-control unit 25P
connector.
6. Turn the ignition switch to ON (II).
7. Check the ABS indicator and the brake system indicator for several sec onds when the ignition
switch is tuned to ON (II).
Troubleshooting is complete.
Replace the ABS modulator-control unit
(see page 19-90).
8. Disconnect the ABS modulator-control unit 25P connector (see step 2 on page 19-90).
9. Turn the ignition switch to ON (II).
10. Measure the voltage between ABS modulator- control unit 25P connector terminal No. 16 and
body ground.
Go to step 11.
Repair open in the wire between the No. 4
(7.5 A) fuse in the under-dash fuse/relay box and
the ABS modulator-control unit.
11. Turn the ignition switch to LOCK (0).
Wire side of female terminals
Wire side of female terminals
Isthefuseblown?
Is there continuity? Does t he i nd i cat or s come on t hen go of f ?
Is there battery voltage?
08/08/21 15:03:17 61SNR030_190_0088
ProCarManuals.com
DYNOMITE -2009-

Diagnostic Trouble Code (DTC)
Self-diagnosis
Kickback
Pump Motor
Brake Fluid Replacement/Air BleedingHow to Troubleshoot DTCs
Intermittent Failures
19-98
VSA System Components
General Troubleshooting Information (cont’d)
 The memory holds all DTCs. However, when the
same DTC is detected more than once, the more
recent DTC is written over the earlier one. Therefore,
when the same problem is detected repeatedly, it is
memorized as a single DTC.
 The DTCs are indicated in the order they occur.
 The DTCs are memorized in the EEPROM. Therefore, the memorized DTCs cannot be erased by
disconnecting the battery. Do the specified
procedures to clear the DTCs.
 Self-diagnosis can be classified into two categories: – Initial diagnosis: Done right after the ignition switch is turned to ON (II) and until the ABS and VSA
indicators go off.
– Regular diagnosis: Done right after the initial diagnosis until the ignition switch is turned to
LOCK (0).
 When the system detects a problem, the VSA modulator-control unit shifts to fail-safe mode.
The pump motor operates when the VSA modulator-
control unit is functioning, and the fluid in the reservoir
is forced out to the master cylinder, causing kickback at
the brake pedal.  The pump motor operates when the VSA modulator- control unit is functioning.
 The VSA modulator-control unit checks the pump motor operation one time after completing initial
diagnosis during regular diagnosis when the vehicle
is driven over 15 km/h (10 mph).
Brake fluid replacement and air bleeding procedures
are identical to the procedures used on vehicles without
the VSA system (see page 19-9). The troubleshooting procedures assume that the cause
of the problem is still present, and the ABS and/or VSA
indicator is still on. Following a troubleshooting
procedure for a code that has been cleared but does not
reset can result in incorrect diagnosis.
1. Question the client about the conditions when the problem occurred, and try to reproduce the same
conditions for troubleshooting. Find out when the
ABS and/or VSA indicator came on, such as during
activation, after activation, when the vehicle was
traveling at a certain speed, etc. If necessary, have
the client demonstrate the concern.
2. When the ABS or VSA indicator does not come on during the test-drive, check for loose connectors,
poor contact of the terminals, etc. in the circuit
indicated by the DTC before you start
troubleshooting.
3. After troubleshooting, or the repairs are done, clear the DTCs, and test-drive the vehicle under the same
conditions that originally set the DTCs. Make sure
the ABS and VSA indicators do not come on.
4. Check for DTCs from other systems which are connected via F-CAN. If there are DTCs that are
related to F-CAN, one possible cause was that the
ignition switch was turned to ON (II) with the VSA
modulator-control unit connector disconnected.
Clear the DTCs. Check for fuel and emissions DTC’s
first.
NOTE: Always troubleshoot fuel and emissions
DTC’s first.
The term ‘‘intermittent failure’’ means a system may
have had a failure, but it checks OK now. If you cannot
reproduce the condition, check for loose connectors or
terminal pins related to the circuit that you are
troubleshooting.
08/08/21 15:04:50 61SNR030_190_0098
ProCarManuals.com
DYNOMITE -2009-

•••
•••
´
´
´

(#'
)
VSA Modulator-Control Unit Inputs and Outputs for 37P Connector (Connector Disconnected)
TerminalnumberWire color Terminal sign Description Signal
19-106VSA System Components
System Description
NOTE: Standard battery voltage is about 12 V.
1 RED CAN-L F-CAN communication circuit
3 BLU STR-D Detects steering angle sensor signal
6 PNK FR-GND Detects right-front wheel speed sensor signal
7 ORN SVCC Power source for the steering angle sensor With ignition switch ON (II): about 5.0 V
8 PUR RL-GND Detects left-rear wheel speed sensor signal
9 LT GRN RR B Detects right-rear wheel speed sensor signal
10 BRN SGND Ground for the steering angle sensor
11 RED FL-GND Detects left-front wheel speed sensor signal
13 WHT FSR B Power source for the fail-safe relay Battery voltage at all times
14 RED MR B Power source for the motor relay Battery voltage at all times
Wire side of female terminals
08/08/21 15:04:53 61SNR030_190_0106
ProCarManuals.com
DYNOMITE -2009-