2006 ACURA CSX battery

Î
Î
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
ABS indicator, brake system indicator, and
VSA indicator do not go off
YES
NO
YES
NO YES
NO
YES
NO
19-166
VSA System Components
Symptom Troubleshooting (cont’d)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
IG1 (GRY) VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
IG1 (GRY)
1. Turn the ignition switch to LOCK (0).
2. Check the No. 4 (7.5 A) fuse in the under-dash fuse/relay box.
Go to step 3.
Reinstall the checked fuse, then go to step 9.
3. Disconnect the VSA modulator-control unit 37P connector (see step 2 on page 19- 171).
4. Disconnect the yaw rate-lateral acceleration sensor 5P connector (see page 19- 169).
5. Check for continuity between VSA modulator- control unit 37P connector terminal No. 28 and
body ground.
Repair short to body ground in the wire
between the No. 4 (7.5 A) fuse in the under-dash
fuse/relay box and the VSA modulator-control unit
or the yaw rate-lateral acceleration sensor.
Install a new No. 4 (7.5 A) fuse in the under-
dashfuse/relaybox,thengotostep6. 6. Reconnect all connectors.
7. Turn the ignition switch to ON (II).
8. Check the ABS indicator, the brake system
indicator and the VSA indicator for several seconds
when the ignition switch is tuned to ON (II).
Troubleshooting is complete.
Replace the VSA modulator-control unit
(see page 19-171).
9. Disconnect the VSA modulator-control unit 37P connector (see step 2 on page 19-171).
10. Turn the ignition switch to ON (II).
11. Measure the voltage between VSA modulator- control unit 37P connector terminal No. 28 and
body ground.
Go to step 12.
Repair open in the wire between the No. 4
(7.5 A) fuse in the under-dash fuse/relay box and
the VSA modulator-control unit.
12. Turn the ignition switch to LOCK (0).
Wire side of female terminals Wire side of female terminals
Isthefuseblown?
Is there continuity? Does t he i nd i cat or s come on t hen go of f ?
Is there battery voltage?
08/08/21 15:06:44 61SNR030_190_0166
ProCarManuals.com
DYNOMITE -2009-

Î
Î
´
µ
µ
µ
µ µ
µ
YES
NO
YES
NO Sign
YES
NO
VSA Modulator- control Unit 37P
Connector Terminal Gauge Control
Module (Tach) 36P
Connector Terminal
19-167
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
GND (BLK)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR FSR B (WHT) VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
CAN-L (RED)CAN-L (RED)
CAN-H (WHT) CAN-H (WHT)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
13. Check for continuity between VSA modulator- control unit 37P connector terminal No. 36 and
body ground.
Go to step 14.
Repair open in the wire between the VSA
modulator-control unit and body ground (G 202).
14. Measure the voltage between VSA modulator- control unit 37P connector terminal No. 13 and
body ground.
Go to step 15.
Repair open in the wire between the No. 3
(40 A) fuse in the under-hood fuse/relay box and
the VSA modulator-control unit. 15. Disconnect the gauge control module (tach) 36P
connector.
16. Check for continuity between VSA modulator- control unit 37P connector terminal and gauge
control module (tach) 36P connector terminal (see
table).
CAN-L No. 1 No. 19
CAN-H No. 15 No. 1
Check for loose terminals in the VSA
modulator-control unit 37P connector. If necessary,
substitute a known-good VSA modulator-control
unit (see page 19-171), and retest.
Repair open in the wire between the gauge
control module (tach) and the VSA modulator-
control unit.
Wire side of female terminals
Wire side of female terminals Wire side of female terminals
Wire side of female terminals
Is there continuity?
Is there battery voltage? Is there continuity?
08/08/21 15:06:45 61SNR030_190_0167
ProCarManuals.com
DYNOMITE -2009-

(#')
Symptom Diagnostic procedure
20-54
Moonroof
Symptom Troubleshooting Index
Water leaks from moonroof 1.
2.
3.
4.
5.Check for a clogged drain tube.
Check for a gap between the glass weatherstrip and the roof panel
(see page 20-55).
Check for a defective or an improperly installed glass weatherstrip or drain
channel.
Check for a gap between the drain seal and the roof panel.
Adjust the moonroof position.
Wind noise from moonroof 1.
2.Check for excessive clearance between the glass weatherstrip and the roof
panel.
Adjust the moonroof position.
Motor noise from moonroof 1. 2.
3.Check for a loose motor.
Check for a worn gear or bearing.
Check for a deformed cable assembly.
Moonroof glass does not move,
but motor turns 1.
2.
3.
4.Check for a defective gear or inner cable.
Check for foreign matter stuck between the guide rail and the slider.
Check for a loose inner cable.
Make sure the cable assembly is attached properly.
Moonroof glass does not move
and motor does not turn (glass
can be moved with 5 mm
hexagonal wrench) 1.
2.
3.
4.Check for a blown fuse.
Check for a faulty moonroof switch.
Check for a run down battery.
Check for a defective motor control unit.
Moonroof glass does not stop at
proper flush closed position 1.
2.Reset the moonroof control unit (see page 22-287).
Check glass position adjustment.
During auto close operation,
moonroof glass r everses when
no object is trapped Check for dirt and debris in the track. Reset the moonroof control unit (see page
22-287).
Moonroof glass moves, but
there is no AUTO function Reset the moonroof control unit (see page 22-287).
08/08/21 15:00:18 61SNR030_200_0056
ProCarManuals.com
DYNOMITE -2009-



Î
(#'

 )
S

pecial Tools Required
20-84 Interior Trim
Headliner Removal/Installation
A
B
C A
B
F
astener Locations
:TORXScrew,2
AB
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations, (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:  A-pillar trim, both sides (see page 20-69)
 Ceiling light (see page 22-197)
 Front seat belt upper anchor, both sides (see step6 on page 24-4)
 B-pillar lower trim, both sides (see page 20-72)
 B-pillar upper trim, both sides (see page 20-72)
 C-pillar trim, both sides (see page 20-75)
 Grab handles, four places (see page 20-82)
3. Release the tabs (A) from the bracket (B) of the sunvisor cap (C) with a trim tool. 4

. Remove the sunvisor cap (A) from the bracket (B).
5. From both sides, remove the sunvisor (A). –1 Remove the sunvisor from the body and theholder (B).
–2 Remove the screws with a TORX T25 bit.
–3 Remove the sunvisor from the body, and if equipped disconnect the vanity mirror light
connector.
08/08/21 15:01:39 61SNR030_200_0086
ProCarManuals.com
DYNOMITE -2009-

Î
20-87
Fastener Locations:Bolt,1
A :Bolt,2
B
A
B C
B D
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
5x0.8mm
6N·m
(0.6 kgf·m, 4 lbf·ft)
16. If necessary, remove the side curtain airbag mounting bolt (A) and grab handle bracket
mounting bolts (B), then remove the grab handle
bracket (C) from each side by releasing the hooks
(D). 17. Install the headliner in the reverse order of removal,
and note these items:
 If the side curtain airbag has deployed, replace the headliner and related parts with new ones
(see page 24-185).
 To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the removed pieces and replace
them if they have any of the following damage:
– Any crease or tears in the headliner (A)
– Any cracks or breakage in the grab handle (B)
– Any damages around the grab handle holes (C) or sunvisor holes in the headliner
– Any cracks in the sunvisor stay base (D)
– Any bends or cracks in the sunvisor stay shaft (E)
– Any cracks in the sunvisor base (F)
– Any cracks or breakage in the vanity mirror base (G)
– Any Velcro fasteners (H) and the clip bases (I) which have come off the headliner
 When installing the grab handle, push on the grab handle against the bracket (J) until the clips
(K) snap into place securely.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace the removed cushion tape with new ones.
 Check that both sides of the headliner are securely attached to the trim.
 Make sure the headliner overlaps the trim pieces correctly (see page 24-187).
 When reinstalling the headliner through the front passenger’s door opening, be careful not to fold
or bend it. Also, be careful not to scratch the
body.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68).
(cont’d)
08/08/21 15:01:41 61SNR030_200_0089
ProCarManuals.com
DYNOMITE -2009-

(#'

 )
(#' )
S

pecial Tools Required
Special Tools Required
20-10820-108Dashboard
Side Defogger Vent Trim Removal/
Installation
Dashboard/Steering Hanger Beam
Removal/Installation
A
B C
KTC trim tool set SOJATP2014
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to scratch the dashboard and related parts.
1. Insert the trim tool into a gap between the side defogger vent trim (A) and the dashboard (B), and
release the hook (C).
2. Install the side defogger vent trim in the r everse
order of removal. KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Have an assistant help you when removing and installing the das hboard/steering hanger beam.
 Take care not to scratch the dashboard, the body and other related parts.
 Put on gloves to protect your hands.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:  Driver’s dashboard lower cover (see page20-102)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Glove box (see page 20-104)
 Kick panel, both sides (see page 20-66)
 A-pillar trim, both sides (see page 20-69)
 Steering column (see page 17-10)
 EPS control unit (see page 17-84)
08/08/21 15:02:57 61SNR030_200_0110
ProCarManuals.com
DYNOMITE -2009-



Special bolt tightening on passenger’s side
20-113
A
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft) A
B
C
A
B
C
B C
14. Install the dashboard in the r
everse order of
removal, and note these items:
 Before tightening the bolts, make sure the wire harnesses are not pinched.
 Make sure the connectors are plugged in properly, and the antenna lead and each cable
are connected properly.
 Before reinstalling the dashboard, screw the special bolts (A) into the adjusting nuts (B), and
check that they turn together. If they do not turn
together, replace the special bolts.
 After setting the dashboard in the body, reinstall all of the mounting bolts but do not tighten them.
First tighten the driver’s side bracket bolts to the
specified torque. Next, loosen the special bolts to
turn the adjusting nuts out of the sleeves (C) until
the nuts contact the body. Then tighten the
special bolts to the specified torque.
 Tighten all remaining mounting bolts to the specified torque.
 Apply medium strength liquid thread lock to the bolts securing the center bracket and the
dashboard before reinstallation.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68).
08/08/21 15:02:59 61SNR030_200_0115
ProCarManuals.com
DYNOMITE -2009-




(#'

 )
S

pecial Tools Required
20-118 Seats
Front Seat Removal/Installation
A
A
7/16
-20 UNF
32 N·m
(3.3 kgf·m, 24 lbf·ft)
A
B
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
 Take care not to scratch the body or tear the seat covers.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Tilt the steering wheel all the way up, and push it all the way in. Adjust the seat-back recline to a
middle position.
3. Slide the front seat forward fully. Carefully pry up on the bottom edge of the anchor cover (A) to
release the hooks, and remove the cover. 4.

Remove the lower anchor bolt (A).
5. Remove the seat track outer end covers (A) and the seat track center end covers (B) from the back of
both seat tracks.
08/08/21 15:03:07 61SNR030_200_0120
ProCarManuals.com
DYNOMITE -2009-