2006 ACURA CSX gearbox




Î
Î
13-17
A
B 10x1.25mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
10x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
A B
C
10x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
10x1.25mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)10 x 1.25 mm
38 N·m
(3.9 kgf·m,
28 lbf·ft) 12x1.25mm
74 N·m
(7.5 kgf·m,
55 lbf·ft)
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m,
55 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m, 55 lbf·ft) B
A
A
14x1.5mm
93 N·m
(9.5 kgf·m,
69 lbf·ft)
16. Install the steering gearbox stiffener plate (A) andthe harness clip (B).
17. Install the stiffener plate (A) and the mounting bracket (B). Connect the exhaust mounting rubber
(C).
18. Connect the lower ball joint and the lower arm (see step 8 on page 16-21).
19. Lower the vehicle on the lift. 20. Install the transmission mount bracket (A), and
connect the ground cable (B).
21. Raise the vehicle on the lift.
22. Loosen and retighten the lower torque rod mounting bolt (A).
23. Refill the transmission with the recommended transmission fluid (see page 13-5).
24. Lower the vehicle on the lift.
(cont’d)
Replace.Replace.
Replace.
08/08/21 14:44:27 61SNR030_130_0019
ProCarManuals.com
DYNOMITE -2009-




Î


13-88Manual Transmission
Transmission Removal (cont’d)
A
B
C
A
B A
B
A
21. Remove the stiffener plate (A) from the left side ofthe steering gearbox, and the mounting bracket (B)
from the right side of the steering gearbox.
Disconnect the exhaust mounting rubber (C).
22. Remove the stiffener plate (A) and the harness clip (B). 23. Remove the front engine mount mounting bolt (A)
and nut (B), then remove the lower radiator hose
from the front engine mount bracket.
24. Remove the front engine mount (A) from the transmission and the engine.
08/08/21 14:47:22 61SNR030_130_0090
ProCarManuals.com
DYNOMITE -2009-





Î
Î
13-89
A
A BB
A B
C VSB02C000016
A
AB
A
A
25. Remove the lower torque rod mounting bolt.
26. Remove the middle subframe mounting bolts (A).
27. Note the reference marks (A) on both sides of the
front subframe that lines up with the body (B). 28. Attach the front subframe adapter (VSB02C000016)
to the front subframe, and hang the belt (A) of the
subframe attachment over the front subframe, then
secure the belt with the stop (B).
29. Raise the jack, and line up the slots in the arms with the bolt holes on the corner of the jack base (C),
then attach them securely.
30. Remove the front subframe mounting bolts (A) and the front subframe (B).
NOTE: Suspend the steering gearbox with an
appropriate size wire.
(cont’d)
08/08/21 14:47:24 61SNR030_130_0091
ProCarManuals.com
DYNOMITE -2009-









13-93
14x1.5mm
88 N·m
(9.0 kgf·m,
65 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m,
55 lbf·ft)
A
A 12x1.25mm
64 N·m
(6.5 kgf·m,
47 lbf·ft)
10x1.25mm
54 N·m
(5.5 kgf·m,
40 lbf·ft)
10x1.25mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
A
B
12. Install a new lower torque rod bracket mounting bolt.
13. Install the front engine mount bracket (A) on the transmission and the engine with new bolts.
14. Loosely tighten a new front engine mount bracket mounting bolt (A), then attach the lower radiator
hose to the front engine mount bracket. 15. Install new middle subframe mounting bolts.
16. Install the steering gearbox stiffener plate (A) and
the harness clip (B).
(cont’d)
Replace. Replace.
Replace. Replace.
08/08/21 14:47:27 61SNR030_130_0095
ProCarManuals.com
DYNOMITE -2009-








14-237
A
BC A
B
C
25. Remove the steering gearbox bracket mounting bolts.
26. Remove the steering gearbox mounting bolt (A), the stiffener mounting bolt (B), and the stiffener (C). 27. Remove the steering gearbox mounting bolt (A),
the stiffener mounting bolt (B), and the stiffener (C).
28. Remove the bolt securing the harness clamp bracket.
(cont’d)
08/08/21 14:46:56 61SNR030_140_0239
ProCarManuals.com
DYNOMITE -2009-




14-239
VSB02C000016
A
B
C
ABC
D
E
F
33. Attach the front subframe adapter (VSB02C000016)
to the front subframe by looping the strap (A) over
the front of the front subframe, then secure the
strap with the stop (B), then tighten the wing nut (C).
34. Raise a jack and line up the slots in the arms with the bolt holes on the corner of the jack base, then
tighten the bolts.
35. Remove the four bolts securing the front subframe, and lower the front subframe.
36. Secure the steering gearbox to the body with a rope. 37. Remove the driveshafts from the differential and
the intermediate shaft. Coat all precision machined
surfaces with clean engine oil, then put plastic bags
over the driveshaft ends.
38. Remove the three bolts securing the shift cable holder (A), then remove the shift cable cover (B).
39. Pry up the lock tab of the lock washer (C), and remove the lock bolt (D) and the lock washer, then
separate the shift cable (E) from the selector control
shaft (F). Do not bend the shift cable excessively.
(cont’d)
08/08/21 14:48:40 61SNR030_140_0241
ProCarManuals.com
DYNOMITE -2009-








14-246Automatic Transmission
Transmission Installation (cont’d)
14x1.5mm
103 N·m
(10.5kgf·m,75.9lbf·ft)
14x1.5mm
103 N·m
(10.5 kgf·m, 75.9 lbf·ft)
A BCC
B A 14x1.5mm
88 N·m (9.0 kgf·m, 65 lbf·ft)
C
10x1.25mm
54 N·m
(5.5 kgf·m,
40 lbf·ft) A
B
10x1.25mm
59 N·m
(6.0 kgf·m,
43 lbf·ft)
23. Loosely install new front subframe mounting bolts.
24. Align the reference marks (A) on the front subframe (B) with the edge (C) of the body, and tighten the
mounting bolts to the specified torque. 25. Secure the lower torque rod with a new bolt.
26. Position the steering gearbox on the gearbox
mounting bracket of the front subframe.
27. Install the gearbox stiffener (A) in the direction shown. Install the steering gearbox mounting bolt
(B) and the stiffener mounting bolt (C), and tighten
the bolts loosely.
Replace. Replace. Replace.
08/08/21 14:48:46 61SNR030_140_0248
ProCarManuals.com
DYNOMITE -2009-





14-247
A
C
10x1.25mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
B
10x1.25mm
59N·m(6.0kgf·m,43lbf·ft)
A
10x1.25mm
38 N·m (3.9 kgf·m, 28 lbf·ft) A6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64N·m(6.5kgf·m,47lbf·ft)
28. Install the stiffener (A), the steering gearbox
mounting bolt (B), and the stiffener mounting bolt
(C), and tighten the bolts loosely.
29. Install the steering gearbox bracket mounting bolts (A).
30. Tighten the steering gearbox mounting bolts and the stiffener mounting bolts to the specified torque. 31. Install the bolt securing the harness clamp bracket.
32. Install both front subframe body mount brackets
with new bolts.
(cont’d)
Replace.
Replace.
08/08/21 14:48:46 61SNR030_140_0249
ProCarManuals.com
DYNOMITE -2009-