2006 ACURA CSX lights

GPS Information
23-142Navigation System
System Diagnostic Mode (cont’d)
 ILL-Illumination Indication
(Navigation unit connector A (17P) terminal No. 10)
a) OFF (0) when parking lights, or headlights are off
b) ON (1) when parking lights, or headlights are on
The navigation unit uses the signal to determine
whether to put the navigation screen into the Day or
Night brightness mode. (Setup screen 1)
 Display-this displays the current position of the display
a) (Close) when the display is closed
b) (Open) when the display is open
The navigation unit has a micro switch to detect this. If
open is indicated when the display is closed, replace
the navigation unit. This screen shows the current status of GPS reception.
The circular diagram shows the current location of the
GPS satellites (yellow balls) as they would appear in the
sky. The outer circle represents the horizon (0 degrees
elevation). The middle and inner circles represents 30
and 60 degrees respectively. The very center of the
diagram (90 degrees elevation) is directly overhead.
Nearby obstructions, like tall buildings, will block
satellites in that direction. That is why it is necessary to
be in an open area to effectively troubleshoot GPS
reception issues. The satellites shown on the diagram
correspond to the PRN number in the GPS Details
screen. There are always 24 active GPS satellites in
orbit. Because satellites fail, and have to be removed
from service, spares are always parked in orbit, ready
to be activated. This is why the PRN (satellite ID
number) can be greater than 24.
NOTE:
 When you use this screen for troubleshooting, park the vehicle outside, away from buildings, tall trees,
and high-tension wires for at least 10 minutes with
the engine running.
 Metallic window tinting on the front or side window or after-market electronic accessories mounted near
the navigation unit, GPS antenna, or navigation
display can interfere with GPS acquisition.
 The Number of Satellites box shows the number of acquired satellites (maximum of 12). It should contain
4 or more icons. If not, troubleshoot for GPS icon is
white or not shown (see page 23-122).
 The Current Position shows latitude, longitude, and elevation (in meters). If there are less than 4 satellites,
the elevation can be grossly inaccurate.
 The Date/Time field shows the current date, and also a time that includes daylight savings and other
offsets entered by the client in Setup function Adjust
Time Zone/Clock.
08/08/21 14:07:32 61SNR030_230_0145
ProCarManuals.com
DYNOMITE -2009-

(#'#

 )

(#'#


 )
23-15723-157
Voice Control Switch Replacement Microphone Replacement
B E
D
A C
B
A
A B
SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
1. Remove the steering wheel (see page 17-6).
2. Remove the voice control switch (see page 17-7).
3. Install the audio remote switch in the reverse order of removal. 1. Remove the front individual map light lens (A).
2. Remove the bolts (B), then disconnect the
connectors, and remove the map lights housing (C).
3. Carefully pry off the moonroof switch (D) from the map light housing while pressing in on the
retaining tabs (E).
4. From the moonroof switch (A), remove the screw and microphone (B).
5. Install the microphone in the reverse order of removal.
08/08/21 14:08:39 61SNR030_230_0160
ProCarManuals.com
DYNOMITE -2009-

µµ
´
µ
´
´
´ µ
´
µ
´
´ µ
µ
´
µ
´
´
µ
´
µ
´
´
Î
NAVIGATION UNIT CONNECTOR A (24P)
Type S model
Cavity Wire Color Connect to Except Type S model
Cavity Wire Color Connect to
23-171
A1 RED Dash lights brightness
controller (ILL )
A3 LT BLU Data link connector (DLC) (K-LINE)
A4 GRN Multiplex integrated control unit (MICU) (SCTY RADIO)
A5 BRN Audio remote switch (AUDIO REMOTE GND)
A6 PUR Stereo amplifier (RR SIG )
A7 LT GRN Stereo amplifier (RR SIG )
A10 WHT Stereo amplifier (RL SIG )
A11 BLK Stereo amplifier (RL SIG )
A12 BLK Body ground to G505 (GND)
A13 GRY No. 14 (7.5 A) fuse in the under- dash fuse/relay box (ILL )
A14 PUR No. 35 (7.5 A) fuse in the under- dash fuse/relay box
(ACC RADIO)
A15 BLU ECM/PCM (VSP)
A16 PNK Audio remote switch (AUDIO REMOTE SW)
A17 LT BLU Stereo amplifier (SWD B)
A18 PNK Stereo amplifier (FR SIG )
A19 BLU Stereo amplifier (FR SIG )
A22 RED Stereo amplifier (FL SIG )
A23 BLU Stereo amplifier (FL SIG )
A24 WHT No. 23 (10 A) fuse in the under- hood fuse/relay box
( B BACK UP) A1 RED Dash lights brightness
controller (ILL )
A3 LT BLU Data link connector (DLC) (K-LINE)
A4 GRN Multiplex integrated control unit (MICU) (SCTY RADIO)
A5 BRN Audio remote switch (AUDIO REMOTE GND)
A6 ORN Right rear speaker (RR R )
A7 BLU Right rear speaker (RR R )
A10 BRN Left rear speaker (RR L )
A11 YEL Left rear speaker (RR L )
A12 BLK Body ground to G505 (GND)
A13 GRY No. 14 (7.5 A) fuse in the under- dash fuse/relay box (ILL )
A14 PUR No. 35 (10 A) fuse in the under- dash fuse/relay box
(ACC RADIO)
A15 BLU ECM/PCM (VSP)
A16 PNK Audio remote switch (AUDIO REMOTE SW)
A18 BRN Front passenger’s door speaker, right tweeter (FR R )
A19 GRY Front passenger’s door speaker, right tweeter (FR R )
A22 PNK Driver’s door speaker, left tweeter (FR L )
A23 LT GRN Driver’s door speaker, left tweeter (FR L )
A24 WHT No. 23 (10 A) fuse in the under- hood fuse/relay box
( B BACK UP)
(cont’d)
Wire side of female terminals
08/08/21 14:08:47 61SNR030_230_0174
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
µµ µ
´
´ ´
´´ ´
´
Î Î

AUDIO UNIT CONNECTOR A (17P)
Cavity Wire Color Connect to AUDIO UNIT CONNECTOR B (20P)
Cavity Wire Color Connect to
23-175
A1 RED Dash lights brightness
controller
A2 BRN Left rear speaker ( )
A3 PNK Driver’s door speaker ( ), Left tweeter ( )
A4 GRN Multiplex integrated control unit (MICU) (SCTY RADIO)
A6 LT BLU Multiplex integrated control unit (MICU) (K-LINE)
A7 BRN Front passenger’s door speaker ( ), Right tweeter ( )
A8 ORN Right rear speaker ( )
A9 BLK Body ground to G505 (GND)
A10 GRY No. 14 (7.5 A) fuse in the under- dash fuse/relay box (ILL )
A11 YEL Left rear speaker ( )
A12 LT GRN Driver’s door speaker ( )
A13 BLU ECM/PCM (VSP)
A14 PUR No. 35 (7.5 A) fuse in the under- dash fuse/relay box
(ACC RADIO)
A15 GRY Front passenger’s door speaker ( ), Right tweeter ( )
A16 BLU Right rear speaker ( )
A17 WHT No. 23 (10 A) fuse in the under- hood fuse/relay box
( B BACK UP) B3 BRN Auxiliary jack assembly
(AUX S GND)
B4 GRY Shield for terminals No. 3, No.5,No.13,No.14,andNo.15
(AUX SH GND)
B5 BLU Auxiliary jack assembly (AUX GND)
B6 BRN Audio remote switch (AUDIO REMOTE GND)
B7 PNK Audio remote switch (AUDIO REMOTE SW)
B13 YEL Auxiliary jack assembly (AUX L)
B14 GRN Auxiliary jack assembly (AUX R)
B15 WHT Auxiliary jack assembly (AUX DET)
: The shielded wires have a heat-shrink tube insulating the outside of the wire. The color of the
insulating tube, typically black or dark gray, may
not match the color of the wire listed on the
schematic.
(cont’d)
Wire side of female terminals Wire side of female terminals
08/08/21 14:08:48 61SNR030_230_0178
ProCarManuals.com
DYNOMITE -2009-

Î(#'#
)
µ´
µ
´
´
´
With Navigation
23-184Audio System
Circuit Diagram
3
G2 21 G1
SCTY
RADIO
K-LINE
PUR
PUR
UNDER-DASH FUSE/RELAY BOX
AM/FM ANTENNA
UNDER-HOOD FUSE/RELAY BOX
() ()AM/FM ANTENNA LEAD
AM/FM ANTENNA SUBLEAD
G3
ILL A1
RED RADIO ACC
SCTY
RADIO
K-LINE Q8 Q4 Q1 Q14
LT BLU A3 A4 GRN WHT
A24
VSP
ECM/PCM
BLU A14
PUR
MICU
ACC HOT in ACC (I) and ON (II)
ORN RED
WHT
ACC
BAT
IGNITION SWITCH
No. 23 (10 A)
No. 2 (IG) (50 A)
BATTERY
No. 1 (BAT) (100 A)
A13 A15
ILL
NAVIGATION UNIT
GRY
ANT B
10 k
1.2 k
470
270
100
CH
( DOWN VOL VOL UP
( MODEBRN
A5
BRN
3.9 k
)
) CH
RED/BLK GRN/RED A16
PNK
GRN SW REMOTE AUDIO
AUDIO
REMOTE
GND
9 4 3
10
AUDIO REMOTE SWITCH
BLK
G505
GND RADIO
A12
No.14(7.5A)FUSE
(In the under-dash
fuse/relay box)
DASH LIGHTS
BRIGHTNESS
CONTROLLER AM/FM
ANTENNA
AMPLIFIER
No.14(7.5A)FUSE
(In the under-dash
fuse/relay box) CABLE
REEL CABLE
REEL
DASH LIGHTS
BRIGHTNESS
CONTROLLER STEREO
AMPLIFIER
LT GRN
STEREO
AMPLIFIER No. 17
(15 A)
D1
D4 C2
G2 No. 35
(7.5 A)
(Type S model)
VSPA29 (Type S model)
RADIO B
BRN
HFL-VOICE
CONTROL
SWITCH
J3
RF
SHRF
IN
2
1
08/08/21 14:09:45 61SNR030_230_0187
ProCarManuals.com
DYNOMITE -2009-

Î(#'# 
)
µ´
µ
´
´
´
Without Navigation
23-188Audio System
Circuit Diagram (cont’d)
3
G2 21 G1
SCTY
RADIO
K-LINE UNDER-DASH FUSE/RELAY BOX
AM/FM ANTENNA
UNDER-HOOD FUSE/RELAY BOX
() ()AM/FM ANTENNA LEAD
AM/FM ANTENNA SUBLEAD
G3
ILL A1
RED RADIO ACC
SCTY
RADIO
K-LINE Q8 Q4 Q1 Q14
LT BLU A6 A4 GRN
WHT
A17
VSP
ECM/PCM
BLU A14
PUR
MICU
ACC HOT in ACC (I) and ON (II)
ORN RED
WHT
ACC
BAT
IGNITION SWITCH
No. 23 (10 A)
No. 2 (IG) (50 A)
BATTERY
No. 1 (BAT) (100 A)
A10 A13
ILL GRY
ANT B
10 k
1.2 k
470
270
100
CH
( DOWN VOL VOL UP
( MODEBRN
B6
BRN
3.9 k
)
) CH
RED/BLK GRN/RED B7
PNK
GRN SW REMOTE
AUDIO
AUDIO
REMOTE
GND
9 4 3
10
AUDIO REMOTE SWITCH
BLK
G505
GND RADIO
A9
No.14(7.5A)FUSE
(In the under-dash
fuse/relay box)
DASH LIGHTS
BRIGHTNESS
CONTROLLER AM/FM
ANTENNA
AMPLIFIER
No.14(7.5A)FUSE
(In the under-dash
fuse/relay box) CABLE
REEL CABLE
REEL
DASH LIGHTS
BRIGHTNESS
CONTROLLER
D1
D4
C2
G2 No. 35
(7.5 A)
VSP A29
RADIOB
RF
SHRF
IN
AUDIO UNIT
08/08/21 14:09:48 61SNR030_230_0191
ProCarManuals.com
DYNOMITE -2009-

Î
How to check for audio system condition
No. 3 button
No. 4 button
No. 5 button
FM button (Push and hold 5 sec.)
CD button (Push and hold 5 sec.)
23-191
A
NOTE: The audio unit must be in the code enter screen before performing the self-diagnostic function.
 The self diagnostic function does not find every problem with the audio system. Check any official H onda service
website for more information about the audio system.
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. When you are in the self-diagnostic mode, pressing a preset button starts.
Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence or absence of an LCD failure.
The entire display must appear. If there are dead segments, replace the audio unit.
Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights
are on.
Vehicle speed pulse indication mode: Indicates the vehicle speed pulse.
Reception level check mode: Indicates the reception level (dB). When entering the reception level check mode, the
AM/FM button is used to change the main/sub antenna. See Reception level indication for more information.
DRAM residual quantity indication mode: Indicates the DRAM residual quantity.
(cont’d)
08/08/21 14:09:49 61SNR030_230_0194
ProCarManuals.com
DYNOMITE -2009-

ÎDisplay Specifications
Speaker check mode
23-192 Audio System
Self-diagnostic Function (cont’d)
Entry LCD Lighting
No. 3 button
Entry LCD Lights-outs
No. 3 button
Duty (for the illumination) indication
No. 4 button
Vehicle speed pulse indication
No. 5 button
Reception level indication
FM button
DRAM residual quantity indication
CD button
7. The end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
8. Turn off the audio unit.
9. Push and hold the No. 1 and No. 3 buttons. While holding the buttons, push the VOL push PWR knob to ON. Release the buttons and the speaker check mode begins. A low-frequency hum should sound for about one
minute. Change the test speaker by pushing the SKIP button. If you find a speaker(s) with no sound, check the
speaker and harness connections. If the connections are good, replace the speaker, and retest.
10. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
08/08/21 14:09:50 61SNR030_230_0195
ProCarManuals.com
DYNOMITE -2009-