2006 ACURA CSX lights

µµ µ
¶
¶
¶
¶
¶
¶•••
•••
µ µ •••
µµ
µµ
Fuel and Emissions
Clutch
Item Measurement Qualification Standard or New
Item Measurement QualificationStandard or New Service Limit
2-7
Fuel pressure
regulatorPressure with fuel pressure gauge
connected 330 380 kPa (3.4 3.9 kgf/cm , 48 55 psi)
Fuel tank Capacity 50 L (13.2 US gal)
Engine idle
(K20Z2) Idle speed without load M/T (in neutral) 700 50 rpm
A/T (in N or P) 800 50 rpm
Idle speed with high electrical load
(A/C switch ON, temperature set to
max cool, blower fan on High, rear
window defogger ON, and headlights
on high beam) M/T (in neutral) 780 50 rpm
A/T (in N or P) 800 50 rpm
Engine idle
(K20Z3) Idle speed without load M/T (in neutral) 750 50 rpm
Idle speed with high electrical load
(A/C switch ON, temperature set to
max cool, blower fan on High, rear
window defogger ON, and headlights
on high beam) M/T (in neutral) 750 50 rpm
Clutch pedal Height from floor Except Type S 159.3 mm (6.27 in.) Type S 161.3 mm (6.35 in.)
Stroke 130 140 mm (5.12 5.51 in.)
Flywheel Runout on clutch mating surface 0.05 mm (0.002 in.) max. 0.15 mm (0.006 in.)
Clutch disc Rivet head depth 1.65 2.25 mm (0.065 0.089 in.) 0.7 mm (0.03 in.) Thickness 8.3 8.9 mm (0.33 0.35 in.) 6.0 mm (0.24 in.)
Pressure plate Warpage 0.03 mm (0.001 in.) max. 0.15 mm (0.006 in.) Evenness of the height of the
diaphragm spring fingers 0.6 mm (0.02 in.) max. 0.8 mm (0.03 in.)2
08/08/21 14:07:14 61SNR030_020_0007
ProCarManuals.com
DYNOMITE -2009-

µµ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Item Measurement Qualification Specification
2-23
ELECTRICAL
RATINGS
Battery 12 V 47 Ah/20 HR (12 V 38 Ah/5 HR)
Fuses Under-hood
fuse/relay box
(’06-07 models)100 A, 80 A, 70 A, 50 A, 40 A, 30 A, 20 A, 15 A, 10 A, 7.5 A
Under-hood
fuse/relay box
(’08-09 models) 100 A, 70 A, 60 A, 50 A, 40 A, 30 A, 20 A, 15 A, 10 A, 7.5 A
Under-dash
fuse/relay box 30 A, 20 A, 15 A, 10 A, 7.5 A
Light bulbs Headlight high beam12 V 60 W (HB3)
Headlight low
beam 12 V 51 W (HB4)
Headlight low
beam (HID) 12 V 35 W (D2R)
Front turn signal
lights 12 V 24/2.2 CP (Amber)
Front side marker
lights 12 V 2 CP
Side turn signal
lights LED
Front parking lights 12 V 3 CP
Front fog lights
(TYPE S, PREMIUM
(’08 model), TECH
PKG) 12 V 55 W (H11)
Rear turn signal
lights 12 V 21 W (Amber)
Rear side marker
lights 12 V 3 CP
Brake/taillights 12 V 21/5 W
Taillights 12 V 5 W
High mount brake
light (except TYPE
S) 12 V 21 W
High mount brake
light (TYPE S) LED
Back-up lights 12 V 16 W
Licenseplatelights 12V 5W
Ceiling light 12 V 8 W
Trunk light 12 V 5 W
Front individual
map lights 12 V 8 W
Gauge lights LED
Indicator lights LED
Ambient light LED
Door courtesy
lights 12 V 3.4 W
Vanity mirror lights 12 V 2 W
Glove box light 12 V 3.4 W
Footwell lights
(TYPE S) LED
Washer reservoir Capacity 4.5 L (4.8 US qt)
08/08/21 14:07:26 61SNR030_020_0023
ProCarManuals.com
DYNOMITE -2009-



(#'
") ¶
¶
Ignition Timing
M/T model: 8 ° 2 ° BTDC (RED mark (B)) at
idle in neutral
A/T model: 8 ° 2 ° BTDC (RED mark (B)) at idle in N or P
4-20Ignition System
Ignition Timing Inspection
A
B
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
4. Check for DTCs (see page 11-3). If a DTC is present, diagnose and repair the cause before continuing
with this test.
5. Start the engine. Hold the engine speed at 3,000 rpm with no load (in N or P (A/T model) or
neutral (M/T model)) until the radiator fan comes
on, then let it idle.
6. Check the idle speed (see page 11-309).
7. Jump the SCS line with the HDS.
8. Connect the timing light to the service loop (white tape). 9. Aim the light toward the pointer (A) on the cam
chain case. Check the ignition timing under a no
load condition (headlights, blower fan, rear window
defogger, and air conditioner are turned off).
10. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK,
update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7), then recheck. If the
system work properly, and the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228).
11. Disconnect the HDS and the timing light.
08/08/21 14:10:07 61SNR030_040_0021
ProCarManuals.com
DYNOMITE -2009-



(#'


)
µ
µ µ
µ
YES
NO YES
NO
4-29
Alternator Control Circuit Troubleshooting
BATTERY
ALTERNATOR
4P CONNECTOR C (WHT/GRN) ALT C
(WHT/GRN)
ECM/PCM CONNECTOR B (44P)
1. Connect the Honda Diagnostic System (HDS) to the
data link connector (DLC) (see step 2 on page 11-3).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
4. Check for DTCs (see page 11-3). If a DTC is present, diagnose and repair the cause before continuing
with this test.
5. Disconnect the alternator 4P connector.
6. Start the engine, and turn on the headlights to high beam.
7. Measure the voltage between alternator 4P connector terminal No. 2 and the positive terminal
of the battery.
Go to step 11.
Go to step 8.
8. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0).
NOTE: This step must be done to protect the ECM/
PCM from damage.
9. Disconnect ECM/PCM connector B (44P). 10. Check for continuity between ECM/PCM connector
terminal B41 and body ground.
Repair short to ground in the wire between
alternator 4P connector terminal No. 2 and ECM/
PCM connector terminal B41.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
11. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0).
NOTE: This step must be done to protect the ECM/
PCMfromdamage.
12. Disconnect ECM/PCM connector B (44P).
(cont’d)
Wire side of
female terminals Terminal side of female terminals
Is t her e 1 V or l ess?
Is there continuity?
08/08/21 14:10:12 61SNR030_040_0030
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
´
µ
4-46 Cruise Control
Circuit Diagram
(A/T model) 764 5 12
G504 11
3
LIGHTS
CRUISE CONTROL INDICATOR
C21
C20
C12
12 V
5V
C4
G401 3 2 C1
A20
3
2 4
1 (50 A) No. 2
No. 19 (15 A) No. 21 (15 A)
A8
A6
C43 B28 GRY
ORN
ECM/PCM A37
A36
BAT
IG1
A39
A40
C39
C3
A41
THROTTLE BODY
TP SENSOR
No. 3
(10 A)
CRUISE MAIN INDICATOR
DRIVER
GAUGE CONTROL MODULE (TACH)
No. 12
(15 A)
UNDER-HOOD FUSE/RELAY BOX
BATTERY
No. 1 (100 A)
CPU
IG1 HOT in
ON (II) and
START (III)
CABLE
REEL
CAN-
CEL RESUME/
ACCEL
CABLE
REEL
THROTTLE
ACTUATOR
BRAKE
PEDAL
POSITION
SWITCH MULTIPLEX
INTEGRATED
CONTROL UNIT
TRANSMISSION
RANGE SWITCH SET/
DECEL
CRUISE
CONTROL
MAIN
CRUISE CONTROL
DIMMING CIRCUIT
PGM-FI
MAIN
RELAY 1
ETCS
CONTROL
RELAY
UNDER-DASH
FUSE/RELAY
BOX HORN
SWITCH
CRUISE CONTROL
COMBINATION SWITCH
IGNITION
SWITCH
IG1ETCS
ETCSRLY
IGP
MRLY CANL
CANH
BKSWNC
BKSW
TPSB
TPSA
VCC3
ETCSM
NC ATPFWD SG3
ETCSM
CRMTCLS
D8
H1 F9 F6 F5 E1
3
6
19101114
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED SENSOR CLUTCH
PEDAL
POSITION
SWITCH No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
YEL
WHT BLU
YEL
LT BLU
BLK LT GRN ORN RED
LT GRN BRN ORN GRN WHT WHT
YEL RED
5V
BLU/WHT LT BLU BLU/YEL BLU
BLU/RED
GRN/YEL GRN RED/BLK RED/BLU
BLK
WHT
D2
F5 42 31
32
41 1
10
679 8 2
21 18 C101
(M/T model) CANL CANH
19
08/08/21 14:10:50 61SNR030_040_0047
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ
µ
µ
YES
NO
YES
NO
DTC P0562:
11-14011-140PGM-FI System
DTC Troubleshooting (cont’d)
36. Monitor the OBD STATUS for DTC P050B in the
DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCs were indicated in step 35, go to the indicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the CKP sensor,
the throttle body, the MAF/IAT sensor, ECT
sensor 1, ECT sensor 2, and the ECM/PCM. If the
ECM/PCM was updated, substitute a known-good
ECM/PCM (see page 11-7), then go to step 33. If the
ECM/PCM was substituted, go to step 1. If the
screen indicates EXECUTING, keep idling until a
result comes on. If the screen indicates OUT OF
CONDITION, go to step 33. NOTE:
 Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If any high current load accessories are installed, this DTC can be set.
 If DTC P16BB and/or P16BC is stored at the same time as DTC P0562, troubleshoot DTC P16BB and/or P16BC
first, then recheck for DTC P0562.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check under these conditions: A/Con
 Temperature control at maximum cool
 Blower fan at maximum speed
 Rear window defogger on
 Headlights on high beam
5. Hold the engine speed at 2,000 rpm (A/T in P or N, M/T in neutral) for 1 minute.
6. Check for Temporary DTCs or DTCs with the HDS.
Replace the alternator (see page 4-34), then
go to step 7.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the alternator and the under-hood fuse/relay box,
and check the battery performance (see page
22-67).Charging System Low Voltage
Does t he scr een i nd i cat e PASSE D?
Is DTC P0562 indicated?
08/08/21 14:18:57 61SNR030_110_0140
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ µ
µ
YES
NO YES
NO
DTC P0563:
11-14111-141
7. Turn the ignition switch to ON (II).
8. Reset the ECM/PCM with the HDS.
9. Do the ECM/PCM idle learn procedure (see page
11-310).
10. Start the engine.
11. Check under these conditions:
A/Con
 Temperature control at maximum cool
 Blower fan at maximum speed
 Rear window defogger on
 Headlights on high beam
12. Hold the engine speed at 2,000 rpm (A/T in P or N, M/T in neutral) for 1 minute.
13. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the alternator and the under-hood
fuse/relaybox,thengotostep1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0).
4. Wait 10 seconds.
5. Turn the ignition switch to ON (II).
6. Check for Temporary DTCs or DTCs with the HDS.
Go to step 7.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
atPGM-FImainrelay1andtheECM/PCM.
7. Turn the ignition switch to LOCK (0).
8. Jump the SCS line with the HDS.
9. Disconnect ECM/PCM connector A (44P).
(cont’d)ECM/PCM Power Source Circuit
Unexpected Voltage
Is DTC P0562 indicated? Is DTC P0563 indicated?
08/08/21 14:18:57 61SNR030_110_0141
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
11-161
ECM/PCM CONNECTOR A (44P)
ELD (ORN)
10. Check for continuity between ECM/PCM connectorterminal A23 and body ground.
Repair short in the wire between the ECM/
PCM (A23) and the ELD, then go to step 13.
Go to step 20.
11. Turn the ignition switch to LOCK (0).
12. Replace the ELD (see page 11-226).
13. Reconnect all connectors.
14. Turn the ignition switch to ON (II).
15. Reset the ECM/PCM with the HDS.
16. Do the ECM/PCM idle learn procedure (see page 11-310).
17. Start the engine.
18. Turn on the headlights.
19. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the ELD and the ECM/PCM, then go to
step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. 20. Reconnect all connectors.
21. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
22. Start the engine.
23. Turn on the headlights.
24. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the ELD and the ECM/PCM. If the ECM/
PCM was updated, substitute a known-good ECM/
PCM(seepage11-7),thengotostep22.IftheECM/
PCM was substituted, go to step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.
Terminal side of female terminals
Is there continuity?
Is DTC P1297 indicated? Is DTC P1297 indicated?
08/08/21 14:20:24 61SNR030_110_0161
ProCarManuals.com
DYNOMITE -2009-