2005 TOYOTA AVENSIS transmission

C83132
Match±marks
C83133
C83139
C50259
C
C
C
CA
AA B
BB
C83572
SST
± AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U241E)
40±105
U241E A/T REPAIR MANUAL (RM840U)
(c) Set the match±marks, install the front differential ring gear
case quickly.
(d) Tighten the 10 bolts.
Torque: 95 N
m (969 kgf
cm, 70 ft
lbf)
16. INSPECT TAPERED POLLER BEARING PRELOAD
(a) Install the differential assy to the transaxle case.
(b) Install the transaxle housing to the transaxle case.
(c) Install the 16 bolts.
Torque:
Bolt A, B: 29.4 N
m (300 kgf
cm, 21.7 ft
lbf)
Bolt C: 22.1 N
m (225 kgf
cm, 16.3 ft
lbf)
BoltBolt length (mm)
A, B42
C50
(d) Using SST, turn the differential assy.
SST 09564±32011

C83572
SST
D09182
C83139
40±106
± AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U241E)
U241E A/T REPAIR MANUAL (RM840U)
(e) Using SST and torque wrench, measure the preload of
the differential assy.
SST 09564±32011
Preload
New bearing:
0.20 ± 0.69 N
m (2.0 ± 7.0 kgf
cm, 1.8 ± 6.1 in.
lbf)
Used bearing:
0.10 ± 0.35 N
m (1.0 ± 3.6 kgf
cm, 0.9 ± 3.1 in.
lbf)
Adjusting shim thickness: mm (in.)
MarkThickness
01.90 (0.074)
11.95 (0.077)
22.00 (0.079)
32.05 (0.081)
42.10 (0.083)
52.15 (0.085)
62.20 (0.087)
72.25 (0.089)
82.30 (0.091)
92.35 (0.093)
A2.40 (0.094)
B2.45 (0.096)
C2.50 (0.098)
D2.55 (0.100)
E2.60 (0.102)
F2.65 (0.104)
G2.70 (0.106)
H2.75 (0.108)
J2.80 (0.110)
(f) Remove the 16 bolts.
(g) Using a practice hammer, remove the transaxle housing.
(h) Remove the differential assy.

D25606
SST
D25605
SST
± AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U241E)
40±107
U241E A/T REPAIR MANUAL (RM840U)
17. INSTALL TRANSAXLE HOUSING OIL SEAL
(a) Using SST, drive into a new oil seal.
SST 09350±32014 (09351±32150), 09950±70010
(09951±07150)
(b) Coat the rip of oil seal with a little MP grease.
18. INSTALL DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST, drive into a new oil seal.
SST 09350±32014 (09351±32150), 09950±70010
(09951±07150)
(b) Coat the rip of the oil seal with a little MP grease.

4103Z±01
C83559
C83560
Matchmarks
C83561
C83562
41±78
±
MANUAL TRANSMISSION/TRANSAXLE DIFFERENTIAL CASE ASSY (E355/E356)
E355,E356 M/T REPAIR MANUAL (RM867E)
DIFFERENTIAL CASE ASSY (E355/E356)
OVERHAUL
HINT:
COMPONENTS: See page 41±1 1. REMOVE SPEEDOMETER DRIVE (MTM) GEAR
(a) Remove the speedometer drive (MTM) gear from front dif-ferential case assy.
2. REMOVE FRONT DIFFERENTIAL RING GEAR
(a) Place machmarks on the from the front differential ring gear and from the front differential case.
(b) Remove the 16 bolts. using a plastic hammer, remove the front differential case.
3. INSPECT FRONT DIFFERENTIAL SIDE GEAR BACKLASH
(a) Fixing the front differential pinion to the front differential
case side. Using a dial indicator, measure the front differ-
ential side gear backlash.
Standard backlash: 0.05 ± 0.2 mm (0.0020 ± 0.0079 in.)

SST
C83563
C83564
C83565
C83566
C68517
± MANUAL TRANSMISSION/TRANSAXLEDIFFERENTIAL CASE ASSY (E355/E356)
41±79
E355,E356 M/T REPAIR MANUAL (RM867E)
4. REMOVE FRONT DIFFERENTIAL PINION SHAFT
STRAIGHT PIN
(a) Using SST and a hammer, loosen the stacked part of the
front differential case.
SST 09930±00010
(b) Using a pin punch and a hammer, remove the front differ-
ential pinion shaft straight pin from the front differential
case.
5. REMOVE FRONT DIFFERENTIAL PINION SHAFT
NO.1
(a) Remove the front differential pinion shaft No.1 to the front
differential case.
6. REMOVE FRONT DIFFERENTIAL SIDE GEAR
(a) Remove the 2 front differential pinions, 2 front differential
pinion thrust washers, 2 front differential side gear and 2
front differential side gear thrust washer No.1 from the
front differential case.
HINT:
Revolving front differential pinion, remove the 2 pinion thrust
washers and side gear thrust washers.
7. INSPECT FRONT DIFFERENTIAL PINION THRUST
WASHER
(a) Using a micrometer, measure the thickness of the front
differential pinion thrust washer.
Minimum thickness: 0.94 mm (0.03701 in)
If the thickness exceed the minimum, replace the front differen-
tial pinion thrust washer.

C68518
C83566
C83565
C83567
41±80
± MANUAL TRANSMISSION/TRANSAXLEDIFFERENTIAL CASE ASSY (E355/E356)
E355,E356 M/T REPAIR MANUAL (RM867E)
8. INSPECT FRONT DIFFERENTIAL PINION SHAFT
NO.1
(a) Using a micrometer, measure the outer diameter of the
front differential pinion shaft No.1.
9. INSTALL FRONT DIFFERENTIAL SIDE GEAR
(a) Coat the rotating surface of the front differential side gear
with gear oil.
(b) Install the 2 front differential side gear thrust washers to
the 2 front differential side gears.
HINT:
(c) Install the 2 front differential side gears, 2 front differential
pinions and front differential thrust washers to the front
differential case.
HINT:
Revolving the front differential pinion, install the 2 front differen-
tial pinions with front differential washers.
10. INSTALL FRONT DIFFERENTIAL PINION SHAFT NO.1
(a) Coat the rotating surface of the front differential pinion
shaft No.1 with gear oil.
(b) Install the front differential pinion shaft No.1 to the front
differential case so that the hole for the front differential
pinion shaft straight pin is aliened with the hole in the front
differential case.
11. INSTALL FRONT DIFFERENTIAL PINION SHAFT
STRAIGHT PIN
(a) Using a pin punch and a hammer, install the front differen-
tial pinion shaft straight pin to the front differential case.

C83562
90
11 0
C58905
C70796
Machmarks
C70795
± MANUAL TRANSMISSION/TRANSAXLEDIFFERENTIAL CASE ASSY (E355/E356)
41±81
E355,E356 M/T REPAIR MANUAL (RM867E)
12. ADJUST FRONT DIFFERENTIAL SIDE GEAR
BACKLASH
(a) Fixing the front differential pinion to the front differential
case side. Using a dial indicator, measure the front differ-
ential side gear backlash.
Standard backlash: 0.05 ± 0.2 mm (0.0020 ± 0.0079 in.)
(b) If the backlash is out of the specification, select the front
differential side gear thrust washer and ajust it.
Thrust washer: mm (in.)
Part No.ThicknessMark
41361 ± 282301.00
(0.0397)1
41361 ± 282401.10
(0.0437)2
41361 ± 282501.20
(0.0476)3
41361 ± 282601.30
(0.0516)4
13. INSTALL FRONT DIFFERENTIAL RING GEAR
(a) Using a heater, heart the front differential ring gear to 90
± 100
C (194.0 ± 230.0
F).
(b) Clean the contact surface differential case.
(c) Aligning the both matchmarks, quickly install the front dif-
ferential ring gear to the front differential case.
Torque: 106 N
m (1080 kgf
cm, 77 ft
lbf)
14. INSTALL SPEEDOMETER DRIVE (MTM) GEAR
(a) Install the speedometer drive (MTM) gear to the front dif-
ferential case.

41041±01
C69529
C69530
C69532
C69799
41±72
±
MANUAL TRANSMISSION/TRANSAXLE SHIFT & SELECT LEVER SHAFT ASSY (E355/E356)
E355,E356 M/T REPAIR MANUAL (RM867E)
SHIFT & SELECT LEVER SHAFT ASSY (E355/E356)
OVERHAUL
HINT:
COMPONENTS: See page 41±1 1. REMOVE CONTROL SHIFT LEVER BUSH
(a) Remove the control shift lever bush from the selectingbellcrank No.2.
2. REMOVE SELECTING BELLCRANK DUST COVER NO.1
(a) Remove the selecting bellcrank dust cover No.1 from the selecting bellcrank No.2.
3. REMOVE SELECTING BELLCRANK SUPPORT SUB±ASSY
(a) Remove the nut, washer and selecting bell crank No.2 plate washer from the selecting bellcrank No.2.
(b) Remove the selecting bellcrank support sub±assy from the selecting bell crank No.2.