2005 TOYOTA AVENSIS code

± DIAGNOSTICSABS WITH EBD SYSTEM
05±701
AVENSIS REPAIR MANUAL (RM1018E)
ItemDiagnostic Note Normal Condition Measurement Item /
Range (Display)
WHEEL SPD FR
Wheel speed sensor (FR)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
WHEEL SPD FL
Wheel speed sensor (FL)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speedSpeed indicated on
speedometer
WHEEL SPD RR
Wheel speed sensor (RR)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speed±
WHEEL SPD RL
Wheel speed sensor (RL)
reading / min.: 0 km/h (0
MPH, max.: 326 km/h (202
MPH)
Actual wheel speed±
IG VOLTAGEECU power supply voltage
/ NORMAL or TOO LOWNORMAL : 9.8 V or over
TOO LOW : Below 9.8 V±
SFRRABS solenoid (SFRR) ON /
OFFOperate: ON±
SFRHABS solenoid (SFRH) ON /
OFFOperate: ON±
SFLRABS solenoid (SFLR) ON /
OFFOperate: ON±
SFLHABS solenoid (SFLH) ON /
OFFOperate: ON±
SRRR (SRR)ABS solenoid (SRRR
(SRR)) ON / OFFOperate: ON±
SRRH (SRH)ABS solenoid (SRRH
(SRH)) ON / OFFOperate: ON±
SRLRABS solenoid (SRLR) ON /
OFFOperate: ON±
SRLHABS solenoid (SRLH) ON /
OFFOperate: ON±
AIR BLD SUPPORTAir bleed support /
SUPPORT or NOT SUPNot supported±
TEST MODETest mode / NORMAL or
TESTNORMAL : Normal mode
TEST : During test mode±
#CODESNumber of DTC recorded /
min.: 0, max.: 255Min.: 0, max.: 19±
3. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the Hand±held tester allows the relay, actuator and so on to operate
without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the methods
to shorten the labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Connect the Hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) From the display on the tester, select the ºACTIVE TESTº.

05±702
± DIAGNOSTICSABS WITH EBD SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
ItemVehicle Condition / Test DetailsDiagnostic Note
SFRRTurns ABS solenoid (SFRR) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFRHTurns ABS solenoid (SFRH) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFLRTurns ABS solenoid (SFLR) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFLHTurns ABS solenoid (SFLH) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRRRTurns ABS solenoid (SRRR) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRRHTurns ABS solenoid (SRRH) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRLRTurns ABS solenoid (SRLR) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRLHTurns ABS solenoid (SRLH) ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFRR & SFRHTurns ABS solenoid SFRR & SFRH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFLR & SFLHTurns ABS solenoid SFLR & SFLH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRRR & SRRHTurns ABS solenoid SRRR & SRRH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SRLR & SRLHTurns ABS solenoid SRLR & SRLH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
SFRH & SFLHTurns ABS solenoid SFRH & SFLH ON / OFF
Operation of solenoid
(clicking sound) can be
heard
ABS MOT RELAYTurns ABS motor relay ON / OFFOperation of motor can be
heard
ABS WARN LIGHTTurns ABS warning light ON / OFFObserve combination me-
ter
BRAKE WRN LIGHTTurns BRAKE warning light ON / OFFObserve combination me-
ter
4. FREEZE FRAME DATA
(a) The vehicle (sensor) status memorized during ABS operation or at the time of error code detection can
be displayed using the hand±held tester.
(b) Only one record of the freeze frame data is stored and the freeze frame data generated during ABS
operation are constantly updated. Also, the number of the operations of the ignition switch ºONº after
the freeze frame data is stored can be memorized up to 31 and it can be displayed.
HINT:
If the ignition switch ºONº operation exceeds 31 times, º31º appears on the display.
(c) If the diagnosis code malfunction occurs, the freeze frame data at the occurrence of the malfunction
is stored but the ABS actuation data is not stored.

050X4±14
ABS Check SheetInspector 's
Name:
Customer 's Name
Date Vehicle
Brought InVIN
Licence No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency the Problem Occurs/ /
ContinuouslyIntermittently ( times a day)
ABS does not operate.
ABS does not operate efficiently.
ABS Warning LightRemains ONDoes not Light Up
DTC Check1st Time
2nd TimeNormal Code
Malfunction Code (Code )
Normal CodeMalfunction Code (Code )
Symptomskm
miles
Brake Warning
LightRemains ONDoes not Light Up
STOP LIGHT SW
SYSTEM
Freeze Frame Data
#IG ON
VEHICLE SPDON
OFF
NO SYS
ABS
FAIL SF
km/h
MPH Production Date 05±698
± DIAGNOSTICSABS WITH EBD SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
CUSTOMER PROBLEM ANALYSIS CHECK

0542Q±04
05±766
±
DIAGNOSTICS ABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DIAGNOSTIC TROUBLE CODE CHART
HINT:

Using SST 09843±18040, connect the terminal Tc and CG of the DLC3.

If malfunction is not found when inspecting parts, inspect the ECU and grou\
nd points for poor contact.

If a malfunction code is displayed during the DTC check, check the circuit\
listed for that code. For de-
tails of each code, refer to the ºSee pageº for respective ºDTC No.º\
in the DTC chart.

When 2 or more DTCs are detected, perform circuit inspection one by one unti\
l the problem is identi-
fied.
DTC chart of ABS system:
DTC No.
(See Page)Detection ItemTrouble Area
C0200 / 31 (05±774)Right front wheel speed sensor signal malfunction

Right front speed sensor

Right front speed sensor circuit

Right front speed sensor rotor
C0205 / 32
(05±774)Left front wheel speed sensor signal malfunction

Left front speed sensor

Left front speed sensor circuit

Left front speed sensor rotor
C0210 / 33
(05±778)Right rear wheel speed sensor signal malfunction

Right rear speed sensor

Right rear speed sensor circuit

Right rear speed sensor rotor
C0215 / 34
(05±778)Left rear wheel speed sensor signal malfunction

Left rear speed sensor

Left rear speed sensor circuit

Left rear speed sensor rotor
C0226 / 21
(05±782)Open or short circuit in brake actuator
Brake actuator

SFRR or SFRH circuit
C0236 / 22
(05±782)Open or short circuit in brake actuator
Brake actuator

SFLR or SFLH circuit
C0246 / 23
(05±782)Open or short circuit in brake actuator
Brake actuator

SRRR or SRRH circuit
C0256 / 24
(05±782)Open or short circuit in brake actuator
Brake actuator

SRLR or SRLH circuit
C0273 / 13
(05±784)Open or short circuit in ABS motor relay circuit
ABS motor relay

ABS motor relay circuit
C0278 / 11
(05±787)Open or short circuit in ABS solenoid relay circuit
ABS solenoid relay

ABS solenoid relay circuit
C1237 / 37
(05±807)Wrong tire size
Tire size

Speed sensor rotor
C1241 / 41
(05±808)Low battery positive voltage or abnormally high battery positive
voltage
Battery

Charging system

Power source circuit
C1249 / 58
(05±815)Open circuit in stop light switch circuit
Stop lamp switch

Stop lamp switch circuit
C1300 / 62
(05±819)Malfunction in skid control ECU
Battery

Skid control ECU
C1330 / 35
(05±774)Open circuit in right front speed sensor circuit
Right front speed sensor

Right front speed sensor circuit
C1331 / 36
(05±774)Open circuit in left front speed sensor circuit
Left front speed sensor

Left front speed sensor circuit
C1332 / 38
(05±778)Open circuit in right rear speed sensor circuit
Right rear speed sensor

Right rear speed sensor circuit

05±768
± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
DTC of sensor check function :
Code No.DiagnosisTrouble Area
C1271/71Low output voltage of right front speed sensor

Right front speed sensor

Sensor installation

Sensor rotor
C1272/72Low output voltage of left front speed sensor

Left front speed sensor

Sensor installation

Sensor rotor
C1273/73Low output voltage of right rear speed sensor

Right rear speed sensor

Sensor installation

Sensor rotor
C1274/74Low output voltage of left rear speed sensor

Left rear speed sensor

Sensor installation

Sensor rotor
C1275/75Change in output voltage of right front speed sensorRight front sensor rotor
C1276/76Change in output voltage of left front speed sensorLeft front speed sensor rotor
C1277/77Change in output voltage of right rear speed sensorRight rear sensor rotor
C1278/78Change in output voltage of left rear speed sensorLeft rear speed sensor rotor

0577Y±02
F45094
ABS Warning LightBRAKE Warning
Light
VSC Warning Light SLIP Indicator Light
TRC OFF Indicator
Light
C52361
DLC3 Tc
CG
05±756
±
DIAGNOSTICS ABS WITH EBD & BA & TRC & VSC SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
PRE±CHECK
1.DIAGNOSIS SYSTEM
(a)Check the warning lights. (1)Release the parking brake lever.
(2)When the ignition switch is turned ON, check thatthe ABS warning light, Brake warning light, VSC
warning light, TRC OFF indicator light and SLIP in-
dicator light come on for approx. 3 seconds.
HINT:

When the parking brake is applied or brake fluid level is
low, the Brake warning light comes on.

If the ECU stores DTC, the ABS warning light , VSC warn-
ing light and TRC OFF indicator light come on.

If the indicator check result is not normal, proceed to trou-
bleshooting for the light circuit.
Trouble AreaSee page
ABS warning light circuit05±827
Brake warning light circuit05±840
VSC warning light circuit05±831
TRC OFF indicator light circuit05±844
SLIP indicator light circuit05±848
(b) Without using hand±held tester: Check the DTC.
(1) Using SST, connect terminal Tc and CG of theDLC3.
SST 09843±18040
(2) Turn the ignition switch ON.
(3) Read the DTC from the ABS warning light or VSC warning light on the combination meter.
HINT:

If no code appears, inspect the diagnostic circuit, ABS
warning light circuit or VSC warning light circuit.
Trouble AreaSee page
Tc terminal circuit05±852
ABS warning light circuit05±827
VSC warning light circuit05±831

R01346
Normal Code
Code 1 1 and 21
ON
OFF
4 sec.0.5 sec.
1.5 sec.
2.5 sec. 0.5 sec.
2 sec.
0.25 sec.
0.25 sec.
ON
OFF
Cod e 1 1 Code 21
BR3890
±
DIAGNOSTIC SABS WITH EBD & BA & TRC & VSC SYSTEM
05±757
AVENSIS RE PAIR MANUAL (RM1018E)

A s an example, the blinking patterns for the normal code
an d codes 11 and 21 are shown on the left.
(4 ) Codes are explained in the code table on page
05±766.
(5) After completing the check, disconnect terminal Tc and CG of the DLC3, and turn off the display.
If 2 or more DTCs are detected at the same time, the lowest
numbered DTC is displayed first.
(c) With using the hand±held tester:
Check the DTC.
(1) Hook up the hand±held tester to the DLC3.
(2) Turn the ignition switch ON.
(3) Read the DTC by following the prompts on the tes-ter screen.
HINT:
Please refer to the hand±held tester operator's manual for fur-
ther details.
(d) Without using hand±held tester: Clear the DTCs.
(1) Using SST, connect the terminal Tc and CG of theDLC3.
SST 09843±18040
(2) Turn the ignition switch ON.
(3) Clear the DTCs stored in the ECU by depressing the
brake pedal 8 or more times within 5 seconds.
(4) Check that the ABS warning light and VSC warning
light indicates the normal code blinking pattern.
(5) Remove the SST from the DLC3.
SST 09843±18040
HINT:
Disconnecting the battery cable during repairs will not erase the
DTCs in the ECU.
(e) With using hand±held tester: Clear the DTCs.
(1) Turn the ignition switch ON.
(2) Operate the hand±held tester to erase the codes.
HINT:
Please refer to the hand±held tester operator's manual for fur-
ther details.

± DIAGNOSTICSABS WITH EBD & BA & TRC & VSC SYSTEM
05±759
AVENSIS REPAIR MANUAL (RM1018E)
ItemDiagnostic Note Normal Condition Measurement Item /
Range (Display)
SRLRABS solenoid SRLR / ON
or OFFON : Operate±
SRLHABS solenoid SRLH / ON
or OFFON : Operate±
SRCF(SA1)TRC solenoid SRCF(SA1)
/ ON or OFFON : Operate±
SRCR(SA2)TRC solenoid SRCR(SA2)
/ ON or OFFON : Operate±
SRMF(SMCF,SA3)
TRC solenoid
SRMF(SMCF,SA3)1 / ON
or OFF
ON : Operate±
SRMR(SMCR,STR)
TRC solenoid
SRMR(SMCR,STR) / ON
or OFF
ON : Operate±
ENGINE SPD
Engine Speed/
Min.: 0 rpm, Max.: 6000
rpm
Actual engine speed±
VEHICLE SPD
Maximum wheel speed
sensor reading / min.: 0
km/h (0 MPH), max.: 326
km/h (202 MPH)
Actual vehicle speedSpeed indicated on
speedometer
YAW RATE
Yaw rate sensor/
Min.: ±128 deg/s, Max.:
128 deg/s
±
YAW ZERO VALUE
Memorized zero value/
Min.: ±128 deg/s, Max.:
128 deg/s
±
STEERING ANG
Steering sensor/
Min.: ±1152 deg,
Max.: 1150.875 deg
±
MAS CYL PRS1
Master cylinder pressure
sensor 1 reading / min.: 0
V, max.: 5 VWhen brake pedal is re-
leased : 0.3 ± 0.9 VReading increases when
brake pedal is depressed
TEST MODETest mode / NORMAL or
TESTNORMAL : Normal mode
TEST : During test mode
#CODESNumber of DTC recorded /
min.: 0, max.: 255Min.: 0, max.: 26