MA-22
ENGINE MAINTENANCE (QR20DE·QR25DE)
FLUSHING COOLING SYSTEM
1. Install reservoir tank if removed, and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
If water drain plug on cylinder block is removed, close and tighten it. Refer to EM-89, "CYLIN-
DER BLOCK" .
2. Fill radiator and reservoir tank with water and reinstall radiator cap.
3. Run the engine and warm it up to normal operating temperature.
4. Rev the engine two or three times under no-load.
5. Stop the engine and wait until it cools down.
6. Drain water from the system. Refer to MA-20, "
DRAINING ENGINE COOLANT" .
7. Repeat steps 1 through 6 until clear water begins to drain from radiator.
Checking Cooling SystemELS000ZF
WARNING:
Do not remove radiator cap when the engine is hot. Serious burns occur from high-pressure
engine coolant escaping from radiator.
Wrap a thick cloth around radiator cap and carefully remove the cap. First, turn the cap a quarter
of a turn to release built-up pressure. Then turn the cap all the way.
CHECKING COOLING SYSTEM HOSES
Check hoses for improper attachment, leaks, cracks, damage, loose connections, chafing and deterioration.
CHECKING RADIATOR
Check radiator for mud or clogging. If necessary, clean radiator as follows.
Be careful not to bend or damage radiator fins.
When radiator is cleaned without removal, remove all surrounding parts such as cooling fan, radiator
shroud and horns. Then tape harness and connectors to prevent water from entering.
1. Apply water by hose to the back side of the radiator core vertically downward.
2. Apply water again to all radiator core surface once per minute.
3. Stop washing if any stains no longer flow out from the radiator.
4. Blow air into the back side of radiator core vertically downward.
Use compressed air lower than 490 kPa (4.9 bar, 5 kg/cm2 , 71 psi) and keep distance more than 30 cm
(11.8 in).
5. Blow air again into all the radiator core surfaces once per minute until no water sprays out.
CHECKING RADIATOR CAP
Check valve seat of radiator cap.
–Check if valve seat is swollen to the extent that the edge of the
plunger cannot be seen when watching it vertically from the top.
–Check if valve seat has no soil and damage.
PBIC2816E
ENGINE MAINTENANCE (YD22DDTI)
MA-33
C
D
E
F
G
H
I
J
K
MA
B
MA
CHECKING RADIATOR CAP
Check valve seat of radiator cap.
–Check if valve seat is swollen to the extent that the edge of the
plunger cannot be seen when watching it vertically from the top.
–Check if valve seat has no soil and damage.
Pull negative-pressure valve to open it, and make sure that it is
completely closed when released.
–Make sure that there is no dirt or damage on the valve seat of
radiator cap negative-pressure valve.
–Make sure that there are no unusualness in the opening and
closing conditions of negative-pressure valve.
Check radiator cap relief pressure.
–When connecting radiator cap to the radiator cap tester (com-
mercial service tool) and the radiator cap tester adapter (special
service tool), apply engine coolant to the cap seal surface.
Replace radiator cap if there is an unusualness related to the above three.
CAUTION:
When installing radiator cap, thoroughly wipe out the radiator filler neck to remove any waxy residue
or foreign material.
CHECKING RADIATOR SYSTEM FOR LEAKS
To check for leaks, apply pressure to the cooling system with
radiator cap tester (commercial service tool) and radiator cap
tester adapter (special service tool).
WARNING:
Never remove the radiator cap when the engine is hot. Seri-
ous burns could occur from high pressure engine coolant
escaping from the radiator.
CAUTION:
Higher test pressure than specified may cause radiator
damage.
PBIC2816E
SMA967B
Standard:
78 - 98 kPa (0.78 - 0.98bar, 0.8 - 1.0 kg/cm
2 , 11 - 14 psi)
Limit:
59 kPa (0.59bar, 0.6 kg/cm
2 , 9 psi)
SLC755AC
Testing pressure:
157 kPa (1.57 bar, 1.6 kg/cm
2 , 23 psi)
SLC134B
CHASSIS AND BODY MAINTENANCE
MA-43
C
D
E
F
G
H
I
J
K
MA
B
MA
Checking Differential Gear OilELS000BF
Check for oil leakage and oil level. (For details, refer to RFD-8,
"Checking Differential Gear Oil" .)
CAUTION:
Gaskets are not reusable. Never reuse them.
Changing Differential Gear OilELS000BG
1. Drain oil from drain plug and refill with new gear oil.
(For details, refer to RFD-8, "
Changing Differential Gear Oil" .)
2. Check oil level.
CAUTION:
Gaskets are not reusable. Never reuse them.
Balancing WheelsELS000BH
Adjust wheel balance using the road wheel center.
RotationELS000BI
After rotating the tires, adjust the tire pressure.
Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
CAUTION:
When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.Filler plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
SMA012C
Oil grad and Viscosity:
Refer to MA-17, "
RECOMMENDED FLU-
IDS AND LUBRICANTS" .
Capacity:
0.55 (1 lmp pt)
Drain plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
Filler plug:
: 34.5 N·m (3.5 kg-m, 25 ft-lb)
SDIA1151E
Wheel balance (Maximum allowable unbalance):
Refer to WT-6, "
SERVICE DATA AND SPECIFICATIONS (SDS)" .
Tightening torque of wheel nut:
98 - 117 N·m (10 - 12 kg·m, 73 - 86 ft·lb)
SMA829C
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-49
C
D
E
F
G
H
I
J
K
MA
B
MA
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitELS000K3
BELT DEFLECTION AND TENSION
QR20DE and QR25DE
YD22DDTi
*: When engine is cold.
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
ENGINE COOLANT CAPACITY
QR20DE and QR25DE
Unit: (lmp qt)
YD22DDTi
Unit: (lmp qt)
ENGINE OIL CAPACITY (APPROXIMATE)
QR20DE and QR25DE
Unit: (lmp qt)
YD22DDTi
Unit: (lmp qt)
SPARK PLUG
QR20DE and QR25DE
Unit: mm (in) Tensions of drive belts Auto-adjustment by auto-tensioner
Applied beltBelt deflection with 98 N (10 kg, 22 lb) force applied* mm (in)
New Adjusted Limit for re-adjusting
A/C compressor belt 4 - 5 (0.16 - 0.20) 6 - 7 (0.24 - 0.28) 8.5 (0.335)
Alternator and water pump belt 9.0 - 10.5 (0.354 - 0.413) 11.0 - 12.5 (0.433 - 0.492) 16.5 (0.650)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11 - 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)
Coolant capacity (With reservoir tank at “MAX” level) 7.1 (6-1/4)
Reservoir tank coolant capacity (At “MAX” level) 0.7 (5/8)
Coolant capacity (With reservoir tank at “MAX” level) 9.5 (8-3/8)
Reservoir tank coolant capacity (At “MAX” level) 0.7 (5/8)
Drain and refill With oil filter change 4.1 (3-5/8)
Without oil filter change 3.7 (3-1/4)
Dry engine (Overhaul)4.7 (4-1/8)
Drain and refill With oil filter change 5.2 (4-5/8)
Without oil filter change 4.9 (4-3/8)
Dry engine (Overhaul)6.3 (5-1/2)
Destination Except Russia For Russia
MakeNGK
Standard type LFR5A-11 PLFR5A-11
Hot type LFR4A-11 PLFR4A-11
Cold type LFR6A-11 PLFR6A-11
Spark plug gap Standard: 1.0 - 1.1 (0.039 - 0.043) Nominal: 1.1 (0.043)
IDX-2
ALPHABETICAL INDEX
Numerics
4WD - Wiring diagram ....................................... TF-23
4WD control unit inspection table ...................... TF-30
A
A/C air flow ......................................... ATC-32
, MTC-5
A/C component layout ..................................... ATC-23
A/C compressor clutch removal and installation ...........
ATC-146
A/C compressor precaution ............................. ATC-10
A/C compressor special service tool ................ ATC-14
A/C diagnostic work flow (auto A/C) ................ ATC-34
A/C HFC134a (R134a) system precaution ........ ATC-4
A/C HFC134a (R134a) system service procedure .......
ATC-141
A/C HFC134a (R134a) system service tools ... ATC-15
A/C HFC134a system service equipment precaution ...
ATC-10
A/C lubricant (R134a) ...................................... ATC-24
A/C operational check ......................... ATC-65, MTC-7
A/C performance test diagnoses ..................... ATC-98
A/C reray .......................................................... ATC-94
A/C self-diagnoses (auto A/C) ......................... ATC-57
A/C system description (auto A/C) ................... ATC-27
A/C trouble diagnoses (auto A/C) ....... ATC-34, MTC-3
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-16, MA-40
A/T fluid replacement ............................. AT-17, MA-41
A/T fluid temperature sensor ........................... AT-111
A/T IND - Wiring diagram .................................... DI-53
A/T indicator ........................................................ DI-53
A/T shift lock system ........................................ AT-398
A/T shift lock system - Wiring diagram ............ AT-399
A/T trouble diagnoses .......................... AT-57, AT-251
A/T Wiring diagram AT - 1ST ........................... AT-127
A/T Wiring diagram AT - 2ND .......................... AT-132
A/T Wiring diagram AT - 3RD .......................... AT-137
A/T Wiring diagram AT - 4TH .......................... AT-143
A/T Wiring diagram AT - BA/FTS ..................... AT-376
A/T Wiring diagram AT - CAN .............. AT-98, AT-330
A/T Wiring diagram AT - ENG SS ...... AT-121, AT-383
A/T Wiring diagram AT - FTS .......................... AT-108
A/T Wiring diagram AT - LPSV .......... AT-156, AT-389
A/T Wiring diagram AT - MAIN ........................ AT-395
A/T Wiring diagram AT - OVRCSV .... AT-180, AT-364
A/T Wiring diagram AT - PNP/SW ................... AT-102
A/T Wiring diagram AT - SSV/A ......... AT-163, AT-352
A/T Wiring diagram AT - SSV/B ......... AT-169, AT-358
A/T Wiring diagram AT - TCV ............ AT-150, AT-370
A/T Wiring diagram AT - TPS ............ AT-175, AT-347
A/T Wiring diagram AT - VSS A/T ..... AT-114, AT-334
A/T Wiring diagram AT - VSSMTR .... AT-194, AT-341
Accelerator control system ............................... ACC-2
Accelerator pedal position (APP) sensor ........ EC-409,
EC-416
, EC-432, EC-815, EC-822, EC-838, EC-1099,
EC-1138
, EC-1285, EC-1455, EC-1493, EC-1624
Accelerator pedal released position learning .... EC-46, EC-559
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-42
Air bleeding (hydraulic clutch) .............................. CL-8
Air bleeding for brake system .............................. BR-9
Air cleaner and air duct(QR20DE-QR25DE) ..... EM-16
Air cleaner and air duct(YD22DDTi) ............... EM-142
Air cleaner filter replacement(QR20DE-QR25DE) ........
MA-24
Air cleaner filter replacement(YD22DDTi) ......... MA-35
Air cleaner filter(QR20DE-QR25DE) ................. EM-16
Air cleaner filter(YD22DDTi) ........................... EM-142
Air conditioner cut control .... EC-38, EC-551, EC-988,
EC-1364
Air flow meter - See Mass air flow sensor ....... EC-151,
EC-644
Air mix door control linkage adjustment ......... ATC-78,
ATC-135
, MTC-10, MTC-32
Air mix. door motor ......................... ATC-76, ATC-135
Air spoiler, rear ................................................... EI-30
Alternator ........................................................... SC-13
Ambient sensor ............. ATC-109, ATC-111, ATC-121
Angular tightening application(QR20DE-QR25DE) ......
EM-5
Angular tightening application(YD22DDTi) ..... EM-130
Antenna - See Power antenna ........................... AV-37
APP2PW - Wiring diagram ........... EC-1241, EC-1580
APPS - Wiring diagram . EC-1101, EC-1457, EC-1626
APPS1 - Wiring diagram ................... EC-411, EC-817
APPS2 - Wiring diagram .. EC-418, EC-824, EC-1140,
EC-1495
APPS3 - Wiring diagram ... EC-434, EC-840, EC-1287
ASC/BS - Wiring diagram ............. EC-1208, EC-1547
ASC/SW - Wiring diagram EC-379, EC-782, EC-1220,
EC-1559
ASCBOF - Wiring diagram ................ EC-507, EC-947
ASCD ................................................ EC-529, EC-969
ASCD brake switch EC-387, EC-506, EC-790, EC-946
ASCD indicator lamp ........................ EC-514, EC-954
ASCD steering switch ....................... EC-377, EC-780
ASCIND - Wiring diagram EC-515, EC-955, EC-1342,
EC-1693
Ashtray illumination .......................................... LT-121
Audio .................................................................... AV-4
Auto air conditioner - Wiring diagram ............. ATC-39
Automatic amplifier ........................... ATC-55, ATC-67
Automatic transmission fluid replacement ....... MA-40,
MA-42
Axle ................................................................... MA-46
B
Back door ........................................................... BL-99
Back door window ............................................ GW-15
Back window .................................................... GW-15
BACK/L - Wiring diagram ................................. LT-100
Back-up lamp ...................................... LT-100, LT-118
Back-up lamp switch (M/T) ............................... MT-15
Barometric pressure (BARO) sensor ............ EC-1303,
IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
EC-1641
Basic inspection .. EC-79, EC-578, EC-1012, EC-1382
Battery ................................................................. SC-4
Baulk ring (M/T) .................................... MT-23, MT-41
Blower motor .... ATC-82, ATC-87, ATC-127, MTC-15,
MTC-18
, MTC-24
Blower resistor ................................................ MTC-25
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1153, EC-1508
Boring/horning cylinder block(QR20DE-QR25DE) .......
EM-111
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-44
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-44
Brake lines and cables inspection ..................... MA-44
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-405, EC-809, EC-1313, EC-1664
BRK/SW - Wiring diagram EC-406, EC-811, EC-1314,
EC-1665
Bulb specifications ............................................ LT-152
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DE-QR25DE) .......... EM-58
Camshaft inspection(YD22DDTi) .................... EM-181
Camshaft position sensor (CMPS) EC-1169, EC-1175,
EC-1525
, EC-1531
Camshaft position sensor (PHASE) .. EC-257, EC-701
Camshaft(QR20DE-QR25DE) ........................... EM-56
Camshaft(YD22DDTi) ...................................... EM-180
CAN - Wiring diagram ....... EC-134, EC-634, EC-1057,
EC-1426
, LAN-12, LAN-28, LAN-44, LAN-69, LAN-87,
LAN-105
, LAN-131, LAN-144, LAN-157
CAN (Controller Area Network) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
CAN communication EC-39, EC-133, EC-552, EC-633,
EC-989
, EC-1056, EC-1365, EC-1425, AT-32, AT-97,
AT-329
, TF-45, LAN-11, LAN-27, LAN-43, LAN-68,
LAN-86
, LAN-104, LAN-130, LAN-143, LAN-156
Canister-See EVAP canister ............. EC-525, EC-965
CHARGE - Wiring diagram .................... SC-14, SC-15
Charging system ................................................ SC-13
Chassis and body maintenance ........................ MA-39
CHIME - Wiring diagram ................ DI-54, DI-57, DI-58
CIGAR - Wiring diagram .................................. WW-29
Cigarette lighter ............................................... WW-29
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram EC-1059, EC-1158, EC-1164,
EC-1428
, EC-1513, EC-1520
Clearance lamp ................................................ LT-116
Clock ................................................................... DI-63
CLOCK - Wiring diagram .................................... DI-63
Closed loop control .............................. EC-36, EC-549
Clutch cover ....................................................... CL-16
Clutch disc ......................................................... CL-16
Clutch master cylinder ......................................... CL-9
Clutch operating cylinder ................................... CL-12
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-14
Clutch release mechanism ................................ CL-14
Clutch withdrawal lever ...................................... CL-14
CMPS - Wiring diagram EC-1059, EC-1170, EC-1176,
EC-1428
, EC-1526, EC-1532
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-96
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DE-QR25DE) ..... EM-70
Compression pressure(YD22DDTi) ................ EM-209
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DE-QR25DE)
EM-109
Connecting rod bearing clearance(YD22DDTi) EM-252
Connecting rod bushing clearance(YD22DDTi) EM-246
Connecting rod(QR20DE-QR25DE) ............... EM-109
Connecting rod(YD22DDTi) .............. EM-242, EM-248
CONSULT for engine ......................... EC-103, EC-604
CONSULT-II for engine ................. EC-1034, EC-1405
Control lever (M/T) ............................................. MT-16
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-76
Controller Area Network (CAN) ........ LAN-11, LAN-27,
LAN-43
, LAN-68, LAN-86, LAN-104, LAN-130,
LAN-143
, LAN-156
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-356, EC-759, EC-1127,
EC-1483
Coolant replacement(QR20DE-QR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-30
Cooling circuit (engine)(QR20DE-QR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-30
Cooling fan ............................................ CO-19, CO-37
Cooling fan relay EC-367, EC-770, EC-1137, EC-1492
Coupling sleeve (M/T) ........................... MT-23, MT-41
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-989, EC-1365
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-527
, EC-967
Crankshaft position sensor (POS) ..... EC-250, EC-693
Crankshaft position sensor (TDC) EC-1157, EC-1163,
EC-1512
, EC-1518
Crankshaft(QR20DE-QR25DE) ........................ EM-90
Cylinder block boring(QR20DE-QR25DE) ...... EM-112
Cylinder block boring(YD22DDTi) ................... EM-250
Cylinder block(QR20DE-QR25DE) ................... EM-89
Cylinder block(YD22DDTi) .............................. EM-230
Cylinder head bolt tightening(QR20DE-QR25DE) ........
IDX-4
ALPHABETICAL INDEX
EM-73
Cylinder head bolt tightening(YD22DDTi) ....... EM-211
Cylinder head gasket selection(YD22DDTi) ... EM-212
Cylinder head(QR20DE-QR25DE) ................... EM-70
Cylinder head(YD22DDTi) .............................. EM-209
D
Data link connector ............................ EC-518
, EC-958
Data link connector for Consult ......... EC-105, EC-606,
EC-1034
, EC-1405
DEF - Wiring diagram ....................................... GW-21
Desiccant Assembly ...................................... ATC-156
Diagnosis sensor unit ..................................... SRS-41
Diagnostic trouble code (DTC) ...................... EC-1372
Diagnostic trouble code (DTC) for OBD system EC-19,
EC-55
, EC-533, EC-565, EC-973, EC-998, EC-1351
Diagnostic trouble code (DTC) inspection priority chart
EC-77
, EC-576, EC-1010, EC-1381
Differential gear (FF M/T) ..................... MT-26, MT-44
DLC - Wiring diagram ........................ EC-518, EC-958
Door glass ........................................... GW-80, GW-83
Door glass Fitting Adjustment ............. GW-80, GW-83
Door lock ................................................. BL-91, BL-95
Door mirror ........................................................ GW-86
Door trim ............................................................. EI-32
Door, front .......................................................... BL-18
Door, rear ........................................................... BL-18
Drive belt inspection(QR20DE-QR25DE) ......... MA-20
Drive belt inspection(YD22DDTi) ...................... MA-29
Drive belt(QR20DE-QR25DE) .......................... EM-13
Drive belt(YD22DDTi) ..................................... EM-140
Drive shaft (front) ............................................. FAX-11
Drive shaft (rear) ............................................. RAX-14
Driver air bag .................................................. SRS-30
Dropping resistor (A/T) ...................... AT-160, AT-393
DTC work support ............................................ EC-112
Dual pressure switch ........ ATC-18, ATC-95, ATC-158
Duct and grilles ............................... ATC-137, MTC-33
E
ECM input/output signal ....................... EC-95
, EC-595
ECM power supply EC-125, EC-286, EC-625, EC-719
ECM/PW - Wiring diagram ................. EC-287, EC-720
ECTS - Wiring diagram .... EC-167, EC-654, EC-1095,
EC-1451
EGR function ................ EC-1186, EC-1193, EC-1651
EGR volume control valve ............ EC-1186, EC-1193,
EC-1651
EGRC/V - Wiring diagram ............. EC-1188, EC-1195,
EC-1653
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-294, EC-296,
EC-314
, EC-723, EC-726, EC-745
Electrical load signal circuit ................ EC-480, EC-920
Electrical unit ..................................................... PG-76
Electrical units location ...................................... PG-69
Electronic ignition (EI) system ............. EC-37, EC-550
Engine control circuit diagram ........... EC-93, EC-593,
EC-1025
, EC-1396
Engine control component parts location .......... EC-88,
EC-588
Engine control module (ECM) .......... EC-283, EC-716,
EC-1227
, EC-1229, EC-1566, EC-1568
Engine control system diagram and chart ........ EC-30,
EC-543
, EC-984, EC-1360
Engine coolant temperature sensor (ECTS) ... EC-165,
EC-652
, EC-1093, EC-1449
Engine coolant(QR20DE-QR25DE) .................... CO-9
Engine coolant(YD22DDTi) .............................. CO-32
Engine fail-safe system ....................... EC-78, EC-577
Engine oil filter replacement(QR20DE-QR25DE) .........
MA-25
Engine oil filter replacement(YD22DDTi) MA-36, MA-37
Engine oil precautions .......................................... GI-7
Engine oil replacement(QR20DE-QR25DE) ..... MA-24
Engine oil replacement(YD22DDTi) .................. MA-35
Engine oil(QR20DE-QR25DE) ............................. LU-7
Engine oil(YD22DDTi) ....................................... LU-20
Engine removal(QR20DE-QR25DE) ................. EM-81
Engine removal(YD22DDTi) ........................... EM-222
ETC1 - Wiring diagram ..................... EC-297, EC-728
ETC2 - Wiring diagram ..................... EC-308, EC-739
ETC3 - Wiring diagram ..................... EC-315, EC-746
EVAP canister purge volume control solenoid valve ....
EC-269
, EC-522, EC-884, EC-962
EVAP vapor lines inspection(QR20DE-QR25DE) ........
MA-28
Evaporative emission (EVAP) system EC-522, EC-962
Evaporator .................................................... ATC-158
Exhaust manifold(QR20DE-QR25DE) .............. EM-25
Exhaust manifold(YD22DDTi) ......................... EM-151
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-39
Expansion valve ............................................ ATC-159
Exterior EI-21, EI-22, EI-24, EI-25, EI-26, EI-27, EI-28,
EI-30
, EI-31
F
F/FOG - Wiring diagram ..................... LT-108
, LT-109
F/PUMP - Wiring diagram EC-467, EC-907, EC-1270,
EC-1609
Fan control amp. ............................. ATC-84, ATC-129
Fan switch ....................................................... MTC-18
FIAR - Wiring diagram .................. EC-1253, EC-1592
Final drive (FF M/T) .............................. MT-26, MT-44
Finisher, interior - See Trim ................................ EI-32
Finisher, rear panel ............................................. EI-31
Floor trim ............................................................. EI-38
Flow charts ......................................................... GI-23
Fluid temperature sensor (A/T) ........................ AT-111
Fluorescent leak detector ............................. ATC-160
Flywheel (clutch) ................................................ CL-16
Flywheel runout(QR20DE-QR25DE) .............. EM-116
Flywheel runout(YD22DDTi) ........................... EM-255
Fog lamp, front ................................................. LT-108
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Fork rod (M/T) ....................................... MT-25, MT-43
Freeze frame data EC-56, EC-566, EC-999, EC-1373
FRO2 - Wiring diagram ...................... EC-847, EC-862
Front bumper ....................................................... EI-14
Front disc brake ................................................. BR-27
Front door ........................................................... BL-18
Front Door Trim ................................................... EI-32
Front fog lamp .................................................. LT-108
Front passenger air bag .................................. SRS-35
Front seat .......................................................... SE-24
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner .... SB-2, SRS-3, SRS-40
Front side air bag ............................................. SRS-37
Front suspension ............................................... FSU-5
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FRPS - Wiring diagram .................. EC-1111, EC-1467
FTS - Wiring diagram .................... EC-1107, EC-1463
FUEL - Wiring diagram ...................... EC-221, EC-227
Fuel check valve ................................ EC-522, EC-962
Fuel cut control (at no load high engine speed) EC-38,
EC-551
, EC-988, EC-1364
Fuel filler lid ...................................................... BL-103
Fuel filter .......................................... EC-994, EC-1370
Fuel filter replacement(QR20DE-QR25DE) .......... FL-4
Fuel filter replacement(YD22DDTi) ....... FL-17, MA-34
Fuel gauge ............................................................ DI-4
Fuel injection control system ........... EC-986, EC-1362
Fuel injection system ......................... EC-219, EC-225
Fuel injector adjustment resistor .... EC-1251, EC-1590
Fuel injector and fuel tube(QR20DE-QR25DE) . EM-34
Fuel injector and fuel tube(YD22DDTi) ............ EM-167
Fuel line inspection(QR20DE-QR25DE) . FL-3, MA-24
Fuel line inspection(YD22DDTi) ............ FL-16, MA-34
Fuel pressure check ............................ EC-49, EC-562
Fuel pressure release .......................... EC-49, EC-562
Fuel pump .......... EC-466, EC-906, EC-994, EC-1263,
EC-1602
Fuel pump and gauge(QR20DE-QR25DE) .......... FL-4
Fuel rail pressure sensor ............... EC-1110, EC-1466
Fuel system(QR20DE-QR25DE) .......................... FL-3
Fuel system(YD22DDTi) ..................................... FL-16
Fuel tank(QR20DE-QR25DE) ............................ FL-11
Fuel tank(YD22DDTi) ......................................... FL-23
Fuel temperature sensor ............... EC-1106, EC-1462
Fuse ................................................................... PG-12
Fuse and fusible link box ................................... PG-80
Fusible link ......................................................... PG-12
G
Gauges ................................................................. DI-4
Gear components (M/T) ....................... MT-23, MT-41
Generator .......................................................... SC-13
Generator - See Alternator ................................ SC-13
Generic scan tool (GST) .................. EC-113, EC-1040
Glass .................................................. GW-80, GW-83
GLOW - Wiring diagram EC-1183, EC-1306, EC-1644
Glow plug ....................................... EC-1305, EC-1643
Glow plug(YD22DDTi) .................................... EM-162
Glow relay ..................... EC-1182, EC-1305, EC-1643
Grille - See Exterior ............................................ EI-19
Ground distribution ............................................ PG-13
H
H/LAMP - Wiring diagram ......................... LT-9
, LT-28
H/MIRROR - Wiring diagram ............................ GW-21
Harness connector ............................................. PG-74
Harness layout ................................................... PG-32
Headlamp ............................................................. LT-5
Headlamp aiming control .................................... LT-66
Headlamp washer ............................................ WW-20
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 1 .... EC-179, EC-186, EC-196,
EC-322
, EC-328, EC-666, EC-673, EC-861
Heated oxygen sensor 1 heater ......... EC-139, EC-846
Heated oxygen sensor 2 .... EC-204, EC-211, EC-334,
EC-342
, EC-867
Heated oxygen sensor 2 heater ......... EC-145, EC-851
Heated seat ........................................... SE-18, SE-21
HEATER - Wiring diagram ................................ MTC-6
Heater and cooling unit (Heater core) ............ ATC-131
Heater mirror ..................................................... GW-21
Heater system - Wiring diagram ....................... MTC-6
Heater unit (heater core) .. ATC-136, MTC-27, MTC-30
HFC134a (R134a) system precaution ............... ATC-4
HFC134a (R134a) system service procedure ATC-141
HFC134a (R134a) system service tools .......... ATC-15
HFC134a system service equipment precaution ..........
ATC-10
HO2S1 - Wiring diaram ...... EC-181, EC-189, EC-199,
EC-668
, EC-675
HO2S1H - Wiring diagram ............................... EC-141
HO2S2 - Wiring diagram .... EC-206, EC-214, EC-337,
EC-345
HO2S2H - Wiring diagram ............................... EC-147
Hood .................................................................. BL-12
Horn ................................................................. WW-27
HORN - Wiring diagram ................................... WW-27
How to erase DTC ........................... EC-566, EC-1372
How to erase DTC for OBD system ..... EC-63, EC-999
I
IATS - Wiring diagram .... EC-161
, EC-1089, EC-1445
IATSEN - Wiring diagram ................................ EC-857
Identification ...................................... ATC-12, ATC-13
Idle air volume learning ........................ EC-47, EC-560
Idle speed ........... EC-79, EC-578, EC-1012, EC-1382
Ignition coil ......................................... EC-440, EC-873
Ignition coil(QR20DE-QR25DE) ....................... EM-31
Ignition control system ....................... EC-440, EC-873
Ignition timing ....................................... EC-79, EC-578
IGNSYS - Wiring diagram .................. EC-441, EC-874
ILL - Wiring diagram ......................................... LT-122
Illumination ........................................................ LT-122
In vehicle sensor ........... ATC-111, ATC-113, ATC-122