2005 MERCEDES-BENZ SPRINTER automatic transmission

(4) Remove floor distribution ducts from the center
floor distribution duct.
(5) Remove the shift mechanism (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC -
NAG1/SHIFT MECHANISM - REMOVAL).
(6) Remove center floor distribution duct from the
heater housing.
INSTALLATION
(1) Install the center floor distribution duct onto
the heater housing.
(2) Install the shift mechanism (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC -
NAG1/SHIFT MECHANISM - INSTALLATION).
(3) Install the left and right floor distribution
ducts onto the center floor distribution duct.
(4) Install the left and right floor distribution duct
retaining screws to the instrument panel support.
Tighten the screws to 2 N´m (17 in. lbs.).
(5) Install the defroster ducts (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/DE-
FROSTER DUCTS - INSTALLATION).
(6) Install the instrument panel (Refer to 23 -
BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL ASSEMBLY - INSTALLATION).
HVAC HOUSING
REMOVAL
The heater housing assembly must be removed
from the vehicle and the two halves of the housing
separated for service access of the heater core, evap-
orator and each of the various mode doors.
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
WARNING: REVIEW THE WARNINGS AND CAU-
TIONS IN PLUMBING BEFORE PERFORMING THE
FOLLOWING OPERATION. (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - WARNING) (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
CAUTION)
(1) Recover the refrigerant from the refrigerant
system. (Refer to 24 - HEATING & AIR CONDI-
TIONING/PLUMBING - STANDARD PROCEDURE -
REFRIGERANT RECOVERY)
(2) Partially drain the engine cooling system
(Refer to 7 - COOLING/ENGINE/COOLANT - STAN-
DARD PROCEDURE).
(3) Disconnect and isolate the battery negative
cable.
(4) Remove the air cleaner housing (Refer to 9 -
ENGINE/AIR INTAKE SYSTEM/AIR CLEANER
HOUSING - REMOVAL).
(5) Remove the windshield washer reservoir (Refer
to 8 - ELECTRICAL/WIPERS/WASHERS/WASHER
RESERVOIR - REMOVAL).
(6) Remove the air filter from the ventilation hous-
ing (Refer to 24 - HEATING & AIR CONDITION-
ING/DISTRIBUTION/AIR FILTER - REMOVAL).
(7) Disconnect the wire harness and vacuum con-
nectors from the recirculation door actuator (Refer to
24 - HEATING & AIR CONDITIONING/CONTROLS/
RECIRCULATION DOOR ACTUATOR - REMOVAL).
(8) Disconnect the wire harness connector from the
blower motor resistor block (Refer to 24 - HEATING
& AIR CONDITIONING/CONTROLS/BLOWER
MOTOR RESISTOR BLOCK - REMOVAL).
Fig. 6 Floor Distribution Duct, RH Shown, LH
Typical
1 - HEATER HOUSING
2 - SCREW (1)
3 - RH FLOOR DUCT
4 - CENTER FLOOR DUCT
24 - 34 DISTRIBUTION - FRONTVA
FLOOR DISTRIBUTION DUCTS (Continued)

INDEX
ABS INDICATOR - DESCRIPTION..........8J-9
ABS INDICATOR - OPERATION...........8J-9
A/C COMPRESSOR - DESCRIPTION......24-49
A/C COMPRESSOR - INSTALLATION......24-51
A/C COMPRESSOR - OPERATION........24-49
A/C COMPRESSOR - REMOVAL.........24-50
A/C COMPRESSOR CLUTCH -
DESCRIPTION........................24-8
A/C COMPRESSOR CLUTCH -
OPERATION..........................24-8
A/C CONDENSER - DESCRIPTION........24-52
A/C CONDENSER - INSTALLATION.......24-52
A/C CONDENSER - OPERATION..........24-52
A/C CONDENSER - REMOVAL...........24-52
A/C DISCHARGE LINE - INSTALLATION . . . 24-54
A/C DISCHARGE LINE - REMOVAL.......24-53
A/C EVAPORATOR - DESCRIPTION.......24-54
A/C EVAPORATOR - INSTALLATION......24-55
A/C EVAPORATOR - OPERATION.........24-54
A/C EVAPORATOR - REMOVAL..........24-55
A/C EXPANSION VALVE - DESCRIPTION . . . 24-55
A/C EXPANSION VALVE - DIAGNOSIS
AND TESTING.......................24-56
A/C EXPANSION VALVE - INSTALLATION . . 24-56
A/C EXPANSION VALVE - OPERATION.....24-55
A/C EXPANSION VALVE - REMOVAL.......24-56
A/C HEATER CONTROL - DESCRIPTION . . . 24-12
A/C HEATER CONTROL - INSTALLATION . . . 24-13
A/C HEATER CONTROL - OPERATION.....24-12
A/C HEATER CONTROL - REMOVAL......24-12
A/C HOUSING - INSTALLATION, REAR....24-41
A/C HOUSING - REMOVAL, REAR........24-40
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-3
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-13
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-13
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-14
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-13
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-14
A/C SYSTEM, SPECIFICATIONS...........24-5
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION...............14-17
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING.........................7-5
ACCESSORY SWITCH BEZEL -
INSTALLATION.......................23-54
ACCESSORY SWITCH BEZEL - REMOVAL . . 23-54
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-20
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-34,23-37
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-21
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-20
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-34,
23-37
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-21
ADAPTATION - STANDARD PROCEDURE,
TCM................................8E-8
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-11
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-11
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-34
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-33
ADJUSTERS - FRONT - INSTALLATION,
SEAT ..............................23-78
ADJUSTERS - FRONT - REMOVAL, SEAT . . 23-78
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE.................8O-6
AIR CLEANER ELEMENT - INSTALLATION . . 9-20
AIR CLEANER ELEMENT - REMOVAL
......9-20
AIR CLEANER HOUSING - INSTALLATION
. . 9-20
AIR CLEANER HOUSING - REMOVAL
......9-20
AIR CONDITIONER - DESCRIPTION,
HEATER
.............................24-1
AIR CONDITIONER - OPERATION,
HEATER
.............................24-2AIR COOLER AND PLUMBING -
CLEANING, CHARGE...................11-5
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE................11-4
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-5
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE................11-5
AIR COOLER AND PLUMBING -
OPERATION, CHARGE..................11-4
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE...................11-5
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE.......11-4
AIR FILTER - INSTALLATION.......24-31,24-39
AIR FILTER - REMOVAL..........24-31,24-39
AIR FLOW (MAF) SENSOR -
DESCRIPTION, MANIFOLD.............14-30
AIR FLOW (MAF) SENSOR -
INSTALLATION, MANIFOLD.............14-31
AIR FLOW (MAF) SENSOR - OPERATION,
MANIFOLD..........................14-30
AIR FLOW (MAF) SENSOR - REMOVAL,
MANIFOLD..........................14-31
AIR GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH................24-9
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING............................14-2
AIR OUTLET TEMPERATURE SENSOR -
DESCRIPTION.......................24-14
AIR OUTLET TEMPERATURE SENSOR -
INSTALLATION.......................24-15
AIR OUTLET TEMPERATURE SENSOR -
OPERATION.........................24-15
AIR OUTLET TEMPERATURE SENSOR -
REMOVAL..........................24-15
AIR OUTLETS - INSTALLATION..........24-32
AIR OUTLETS - REMOVAL.............24-31
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-29
AIR TEMPERATURE SENSOR -
INSTALLATION, INLET.................14-30
AIR TEMPERATURE SENSOR -
OPERATION, INLET...................14-29
AIR TEMPERATURE SENSOR -
REMOVAL, INLET....................14-30
AIRBAG - DESCRIPTION, DRIVER........8O-16
AIRBAG - DESCRIPTION, PASSENGER....8O-23
AIRBAG - INSTALLATION, DRIVER.......8O-18
AIRBAG - INSTALLATION, PASSENGER . . . 8O-26
AIRBAG - OPERATION, DRIVER.........8O-17
AIRBAG - OPERATION, PASSENGER......8O-24
AIRBAG - REMOVAL, DRIVER...........8O-17
AIRBAG - REMOVAL, PASSENGER.......8O-24
AIRBAG BRACKET - INSTALLATION,
PASSENGER........................8O-27
AIRBAG BRACKET - REMOVAL,
PASSENGER........................8O-27
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-8
AIRBAG CONTROL MODULE -
INSTALLATION......................8O-11
AIRBAG CONTROL MODULE -
OPERATION..........................8O-9
AIRBAG CONTROL MODULE - REMOVAL . . 8O-10
AIRBAG INDICATOR - DESCRIPTION......8J-10
AIRBAG INDICATOR - OPERATION.......8J-10
ALB CONTROLLER - INSTALLATION
.......5-15
ALB CONTROLLER - REMOVAL
...........5-15
ALB LEVER - INSTALLATION
.............5-15
ALB LEVER - REMOVAL
................5-15
ALIGNMENT - DESCRIPTION, WHEEL
......2-17
ALIGNMENT - SPECIFICATIONS, WHEEL
....2-19
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE
...............21-27
AMBIENT TEMPERATURE INDICATOR -
DESCRIPTION
.......................8J-11
AMBIENT TEMPERATURE INDICATOR -
OPERATION
.........................8J-11
AMBIENT TEMPERATURE SENSOR -
DESCRIPTION
.......................24-15
AMBIENT TEMPERATURE SENSOR -
INSTALLATION
.......................24-16
AMBIENT TEMPERATURE SENSOR -
OPERATION
.........................24-15
AMBIENT TEMPERATURE SENSOR -
REMOVAL
..........................24-15ANTENNA BODY & CABLE -
INSTALLATION.......................8A-1
ANTENNA BODY & CABLE - REMOVAL.....8A-1
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-2
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-1
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER........................8E-3
ANTILOCK BRAKE - REMOVAL,
CONTROLLER........................8E-3
A-PILLAR TRIM - INSTALLATION........23-68
A-PILLAR TRIM - REMOVAL............23-67
ARM - DESCRIPTION, WIPER...........8R-13
ARM - INSTALLATION, CENTER ROLLER . . 23-38
ARM - INSTALLATION, LOWER CONTROL . . . 2-6
ARM - INSTALLATION, LOWER ROLLER . . . 23-38
ARM - INSTALLATION, UPPER ROLLER . . . 23-37
ARM - INSTALLATION, WIPER..........8R-14
ARM - OPERATION, WIPER............8R-14
ARM - REMOVAL, CENTER ROLLER......23-37
ARM - REMOVAL, LOWER CONTROL.......2-6
ARM - REMOVAL, LOWER ROLLER......23-38
ARM - REMOVAL, UPPER ROLLER.......23-37
ARM - REMOVAL, WIPER..............8R-14
ARMREST - INSTALLATION.............23-76
ARMREST - REMOVAL................23-76
ASH RECEIVER - INSTALLATION.........23-55
ASH RECEIVER - REMOVAL............23-55
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - INSTALLATION.................8L-27
ASH RECEIVER/CIGAR LIGHTER LAMP
UNIT - REMOVAL....................8L-27
ASSIST HANDLE - INSTALLATION........23-68
ASSIST HANDLE - REMOVAL...........23-68
AUDIO, SPECIAL TOOLS................8A-1
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING........21-23,21-24
AUTOMATIC TRANSMISSION - NAG1 -
DESCRIPTION........................21-2
AUTOMATIC TRANSMISSION - NAG1 -
OPERATION..........................21-4
AUTOMATIC TRANSMISSION - SPECIAL
TOOLS, NAG1.......................21-69
AUTOMATIC TRANSMISSION -
SPECIFICATIONS, NAG1...............21-68
AUTOMATIC TRANSMISSION FLUID -
NAG1 - DESCRIPTION...................0-4
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-4
AUXILIARY BATTERY INSTALLATION,
INSTALLATION.......................8F-13
AUXILIARY BATTERY REMOVAL,
REMOVAL..........................8F-13
AXLE - DESCRIPTION...................0-3
AXLE - DESCRIPTION, REAR.............3-10
AXLE - DIAGNOSIS AND TESTING, REAR . . . 3-10
AXLE - INSTALLATION, REAR............3-12
AXLE - OPERATION, REAR..............3-10
AXLE - REMOVAL, REAR................3-11
AXLE - SPECIAL TOOLS, REAR...........3-14
AXLE - SPECIFICATIONS, REAR..........3-13
AXLE BEARINGS/SEALS - INSTALLATION . . . 3-17
AXLE BEARINGS/SEALS - REMOVAL......3-17
AXLE HUB BEARINGS/SEALS -
INSTALLATION........................3-20
AXLE HUB BEARINGS/SEALS - REMOVAL . . 3-20
AXLE SHAFTS - DUAL REAR WHEELS -
INSTALLATION........................3-19
AXLE SHAFTS - DUAL REAR WHEELS -
REMOVAL...........................3-19
AXLE SHAFTS - INSTALLATION...........3-15
AXLE SHAFTS - REMOVAL..............3-15
B1 - ASSEMBLY, HOLDING CLUTCH.....21-113
B1 - DISASSEMBLY, HOLDING CLUTCH . . 21-112
B2 - ASSEMBLY, HOLDING CLUTCH.....21-116
B2 - DISASSEMBLY, HOLDING CLUTCH . . 21-115
BACK - FRONT - INSTALLATION, SEAT....23-77
BACK - FRONT - REMOVAL, SEAT
.......23-77
BACK CUSHION/COVER - REAR -
INSTALLATION, SEAT
.................23-80
BACK CUSHION/COVER - REAR -
REMOVAL, SEAT
.....................23-80
BACK SHIELD - INSTALLATION, REAR
SEAT
..............................23-79
BACK SHIELD - REMOVAL, REAR SEAT
. . . 23-79
VAINDEX 1
Description Group-Page Description Group-Page Description Group-Page

DUAL REAR WHEEL INSTALLATION -
STANDARD PROCEDURE...............22-12
DUAL REAR WHEELS - INSTALLATION,
AXLE SHAFTS........................3-19
DUAL REAR WHEELS - REMOVAL, AXLE
SHAFTS.............................3-19
DUCTS - INSTALLATION, DEFROSTER....24-33
DUCTS - INSTALLATION, FLOOR
DISTRIBUTION.......................24-34
DUCTS - INSTALLATION, INSTRUMENT
PANEL.............................24-38
DUCTS - REMOVAL, DEFROSTER........24-33
DUCTS - REMOVAL, FLOOR
DISTRIBUTION.......................24-33
DUCTS - REMOVAL, INSTRUMENT
PANEL.............................24-37
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING............21-102
ELECTRIC COOLANT PUMP -
DESCRIPTION.......................24-57
ELECTRIC COOLANT PUMP -
INSTALLATION.......................24-57
ELECTRIC COOLANT PUMP - OPERATION . 24-57
ELECTRIC COOLANT PUMP - REMOVAL . . . 24-57
ELECTRICAL - DESCRIPTION............5-29
ELECTRICAL - OPERATION..............5-29
ELECTROHYDRAULIC UNIT - ASSEMBLY . . 21-95
ELECTROHYDRAULIC UNIT -
DESCRIPTION.......................21-82
ELECTROHYDRAULIC UNIT -
DISASSEMBLY.......................21-92
ELECTROHYDRAULIC UNIT -
INSTALLATION......................21-100
ELECTROHYDRAULIC UNIT - OPERATION . . 21-87
ELECTROHYDRAULIC UNIT - REMOVAL . . . 21-92
ELECTROLYTE LEVEL - STANDARD
PROCEDURE, CHECKING BATTERY.......8F-12
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-7
ELEMENT - DESCRIPTION, HEATED SEAT . . 8G-3
ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-3
ELEMENT - INSTALLATION, AIR
CLEANER............................9-20
ELEMENT - OPERATION, HEATED SEAT....8G-3
ELEMENT - REMOVAL, AIR CLEANER......9-20
END - DIAGNOSIS AND TESTING, OUTER
TIE ROD............................19-10
END - INSTALLATION, TIE ROD.........19-11
END - REMOVAL, TIE ROD.............19-11
ENGINE - DESCRIPTION.................9-2
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL...............0-1
ENGINE - DIAGNOSIS AND TESTING,
DIESEL.............................11-2
ENGINE - STANDARD PROCEDURE,
COMPRESSION TESTING................9-3
ENGINE BLOCK HEATER - INSTALLATION . . . 7-14
ENGINE BLOCK HEATER - REMOVAL......7-14
ENGINE CONTROL MODULE -
DESCRIPTION........................8E-3
ENGINE CONTROL MODULE -
INSTALLATION........................8E-4
ENGINE CONTROL MODULE - REMOVAL . . . 8E-4
ENGINE COOLANT - DESCRIPTION.........0-1
ENGINE COOLANT TEMP SENSOR -
DESCRIPTION........................7-14
ENGINE COOLANT TEMP SENSOR -
INSTALLATION........................7-15
ENGINE COOLANT TEMP SENSOR -
REMOVAL...........................7-14
ENGINE COOLANT THERMOSTAT -
INSTALLATION........................7-16
ENGINE COOLANT THERMOSTAT -
REMOVAL...........................7-15
ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE, REPLACING....9-34
ENGINE COVER - INSTALLATION..........9-7
ENGINE COVER - REMOVAL
..............9-4
ENGINE CRADLE CROSSMEMBER -
INSTALLATION
........................13-8
ENGINE CRADLE CROSSMEMBER -
REMOVAL
...........................13-6
ENGINE OIL - DIESEL ENGINES -
DESCRIPTION
.........................0-3
ENGINE TEMPERATURE GAUGE -
DESCRIPTION
.......................8J-15ENGINE TEMPERATURE GAUGE -
OPERATION.........................8J-15
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL..............................0-3
ENTRY MODULE - DESCRIPTION,
SENTRY KEY REMOTE.................8Q-2
ENTRY MODULE - INSTALLATION,
SENTRY KEY REMOTE.................8Q-4
ENTRY MODULE - OPERATION, SENTRY
KEY REMOTE........................8Q-3
ENTRY MODULE - REMOVAL, SENTRY
KEY REMOTE........................8Q-3
ENTRY TRANSMITTER - DESCRIPTION,
REMOTE KEYLESS....................8N-2
ENTRY/EXIT LAMP BULB -
INSTALLATION.......................8L-32
ENTRY/EXIT LAMP BULB - REMOVAL.....8L-31
ENTRY/EXIT LAMP UNIT - INSTALLATION . 8L-32
ENTRY/EXIT LAMP UNIT - REMOVAL.....8L-32
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-46
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-47
EVAPORATOR - DESCRIPTION, A/C.......24-54
EVAPORATOR - INSTALLATION, A/C......24-55
EVAPORATOR - INSTALLATION, REAR....24-61
EVAPORATOR - OPERATION, A/C........24-54
EVAPORATOR - REMOVAL, A/C..........24-55
EVAPORATOR - REMOVAL, REAR........24-60
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION....................24-17,24-25
EVAPORATOR TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............24-26
EVAPORATOR TEMPERATURE SENSOR -
INSTALLATION..................24-18,24-26
EVAPORATOR TEMPERATURE SENSOR -
OPERATION....................24-18,24-26
EVAPORATOR TEMPERATURE SENSOR -
REMOVAL.....................24-18,24-26
EXHAUST MANIFOLD - INSTALLATION.....9-59
EXHAUST MANIFOLD - REMOVAL.........9-59
EXHAUST PIPE - INSTALLATION..........11-3
EXHAUST PIPE - REMOVAL.............11-3
EXHAUST TUBE - INSTALLATION........24-73
EXHAUST TUBE - REMOVAL............24-73
EXPANSION VALVE - DESCRIPTION, A/C . . 24-55
EXPANSION VALVE - DIAGNOSIS AND
TESTING, A/C.......................24-56
EXPANSION VALVE - INSTALLATION, A/C . . 24-56
EXPANSION VALVE - INSTALLATION,
REAR..............................24-63
EXPANSION VALVE - OPERATION, A/C....24-55
EXPANSION VALVE - REMOVAL, A/C.....24-56
EXPANSION VALVE - REMOVAL, REAR....24-62
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-3
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING.....................8L-5
EXTERIOR HANDLE - INSTALLATION.....23-16,
23-33,23-36
EXTERIOR HANDLE - REMOVAL . . . 23-16,23-32,
23-36
FAN - INSTALLATION, RADIATOR.........7-13
FAN - REMOVAL, RADIATOR.............7-13
FAN DRIVE VISCOUS CLUTCH -
INSTALLATION........................7-16
FAN DRIVE VISCOUS CLUTCH -
REMOVAL...........................7-16
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, REAR..........13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, REAR..............13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-2
FASTENER USAGE - DESCRIPTION......Intro.-5
FILL - STANDARD PROCEDURE, DRAIN....3-11
FILL - STANDARD PROCEDURE,
TRANSMISSION.....................21-103
FILL AND BLEED PROCEDURE,
STANDARD PROCEDURE - POWER
STEERING PUMP
.....................19-14
FILL DOOR - INSTALLATION, FUEL
.......23-47
FILL DOOR - REMOVAL, FUEL
..........23-47
FILL/CHECK LOCATIONS - INSPECTION,
FLUID
...............................0-4
FILTER - DESCRIPTION, FLUID
.........21-101FILTER - DESCRIPTION, FUEL............14-5
FILTER - INSTALLATION, AIR......24-31,24-39
FILTER - INSTALLATION, FUEL...........14-6
FILTER - INSTALLATION, OIL............9-51
FILTER - OPERATION, FLUID...........21-101
FILTER - OPERATION, FUEL.............14-5
FILTER - REMOVAL, AIR..........24-31,24-39
FILTER - REMOVAL, FUEL...............14-5
FILTER - REMOVAL, OIL................9-51
FILTER - STANDARD PROCEDURES,
DRAINING WATER FROM FUEL...........14-2
FILTER CLOGGED INDICATOR -
DESCRIPTION, FUEL..................8J-15
FILTER CLOGGED INDICATOR -
OPERATION, FUEL....................8J-15
FINESSE SANDING/BUFFING & POLISH -
DESCRIPTION.......................23-75
FINISH - DESCRIPTION, BASECOAT/
CLEARCOAT.........................23-74
FITTING - STANDARD PROCEDURE,
PISTON RING........................9-46
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLOOR DISTRIBUTION DUCTS -
INSTALLATION.......................24-34
FLOOR DISTRIBUTION DUCTS -
REMOVAL..........................24-33
FLOOR MATS - INSTALLATION, CARPETS . 23-70
FLOOR MATS - REMOVAL, CARPETS.......23-69
FLOW (MAF) SENSOR - DESCRIPTION,
MANIFOLD AIR......................14-30
FLOW (MAF) SENSOR - INSTALLATION,
MANIFOLD AIR......................14-31
FLOW (MAF) SENSOR - OPERATION,
MANIFOLD AIR......................14-30
FLOW (MAF) SENSOR - REMOVAL,
MANIFOLD AIR......................14-31
FLUID - DESCRIPTION, BRAKE............0-3
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT..................21-102
FLUID - NAG1 - DESCRIPTION,
AUTOMATIC TRANSMISSION.............0-4
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID AND FILTER - DESCRIPTION.....21-101
FLUID AND FILTER - OPERATION.......21-101
FLUID CAPACITIES - SPECIFICATIONS......0-4
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING......................21-102
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID COOLER TUBE - INSTALLATION....19-14
FLUID COOLER TUBE - REMOVAL.......19-14
FLUID FILL/CHECK LOCATIONS -
INSPECTION..........................0-4
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-27
FLUID INDICATOR - OPERATION,
WASHER...........................8J-27
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT......21-102
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-8
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-14
FLUID/FILTER SERVICE - STANDARD
PROCEDURE.......................21-104
FLUSH - SPECIFICATIONS, GAP.........23-88
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-13
FLYWHEEL - REMOVAL.................9-39
FOG LAMP BULB - INSTALLATION.......8L-10
FOG LAMP BULB - REMOVAL...........8L-10
FOG LAMP RELAY - INSTALLATION......8L-11
FOG LAMP RELAY - REMOVAL..........8L-10
FOG LAMP SWITCH - INSTALLATION
.....8L-12
FOG LAMP SWITCH - REMOVAL
.........8L-11
FRAME DIMENSIONS - SPECIFICATIONS
. . . 13-4
FREEWHEELING CLUTCH - ASSEMBLY
. . . 21-107
FREEWHEELING CLUTCH - DESCRIPTION
. 21-105
6 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-2
MODULE - DESCRIPTION,
TRANSMISSION CONTROL..............8E-5
MODULE - DIAGNOSIS AND TESTING,
CENTRAL TIMER......................8E-2
MODULE - DIAGNOSIS AND TESTING,
CONTROL..........................24-24
MODULE - INSTALLATION, AIRBAG
CONTROL..........................8O-11
MODULE - INSTALLATION, CENTRAL
TIMER..............................8E-2
MODULE - INSTALLATION, CONTROL.....24-25
MODULE - INSTALLATION, ENGINE
CONTROL...........................8E-4
MODULE - INSTALLATION, FUEL TANK....14-14
MODULE - INSTALLATION, SECURITY
SYSTEM............................8Q-2
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-4
MODULE - OPERATION, AIRBAG
CONTROL...........................8O-9
MODULE - OPERATION, CENTRAL TIMER . . 8E-2
MODULE - OPERATION, CONTROL.......24-24
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - OPERATION, TRANSMISSION
CONTROL...........................8E-5
MODULE - REMOVAL, AIRBAG CONTROL . 8O-10
MODULE - REMOVAL, CENTRAL TIMER....8E-2
MODULE - REMOVAL, CONTROL........24-24
MODULE - REMOVAL, ENGINE CONTROL . . . 8E-4
MODULE - REMOVAL, FUEL TANK.......14-13
MODULE - REMOVAL, SECURITY
SYSTEM............................8Q-2
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-3
MOTOR - DESCRIPTION, WIPER........8R-19
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-29
MOTOR - DIESEL - SPECIFICATIONS,
STARTER ...........................8F-29
MOTOR - INSTALLATION, BLOWER . 24-33,24-40
MOTOR - INSTALLATION, DOOR LOCK....8N-1
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-16
MOTOR - INSTALLATION, STARTER......8F-31
MOTOR - INSTALLATION, WIPER........8R-19
MOTOR - OPERATION, WIPER..........8R-19
MOTOR - REMOVAL, BLOWER.....24-32,24-39
MOTOR - REMOVAL, DOOR LOCK........8N-1
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-15
MOTOR - REMOVAL, STARTER..........8F-30
MOTOR - REMOVAL, WINDOW...........8N-5
MOTOR - REMOVAL, WIPER...........8R-19
MOTOR RELAY - DESCRIPTION,
BLOWER...........................24-23
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-31
MOTOR RELAY - DIAGNOSIS AND
TESTING, BLOWER...................24-24
MOTOR RELAY - INSTALLATION,
BLOWER...........................24-24
MOTOR RELAY - INSTALLATION,
STARTER
...........................8F-32
MOTOR RELAY - OPERATION, BLOWER
. . . 24-23
MOTOR RELAY - REMOVAL, BLOWER
....24-24
MOTOR RELAY - REMOVAL, STARTER
....8F-31
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER
...............24-16
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER
...............24-16
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER
..............24-17
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER
...........................24-16
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER
...........................24-16
MOTOR SWITCH - DESCRIPTION,
BLOWER
......................24-17,24-22
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER
..............24-17,24-23
MOTOR SWITCH - INSTALLATION,
BLOWER
...........................24-23
MOTOR SWITCH - OPERATION, BLOWER
. 24-17,
24-22MOTOR SWITCH - REMOVAL, BLOWER . . 24-17,
24-23
MOUNT - INSTALLATION, LEFT...........9-49
MOUNT - INSTALLATION, RIGHT.........9-49
MOUNT - REMOVAL, LEFT..............9-49
MOUNT - REMOVAL, RIGHT.............9-49
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH...........8L-7
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH...............8L-7
MOUNTED STOP LAMP UN -
INSTALLATION, CENTER HIGH...........8L-8
MOUNTED STOP LAMP UN - REMOVAL,
CENTER HIGH........................8L-8
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-2
MULTI-FUNCTION INDICATOR -
DESCRIPTION.......................8J-20
MULTI-FUNCTION INDICATOR -
OPERATION.........................8J-21
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-20
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-19
NAG1 - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................21-2
NAG1 - DESCRIPTION, AUTOMATIC
TRANSMISSION FLUID..................0-4
NAG1 - OPERATION, AUTOMATIC
TRANSMISSION.......................21-4
NAG1 AUTOMATIC TRANSMISSION -
SPECIAL TOOLS.....................21-69
NAG1 AUTOMATIC TRANSMISSION -
SPECIFICATIONS.....................21-68
NOISE - DIAGNOSIS AND TESTING,
COMPRESSOR.......................24-49
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-8
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NOZZLE - DESCRIPTION, WASHER.......8R-9
NOZZLE - INSTALLATION, WASHER.......8R-9
NOZZLE - OPERATION, WASHER.........8R-9
NOZZLE - REMOVAL, WASHER...........8R-9
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-1
ODOMETER - DESCRIPTION............8J-21
ODOMETER - OPERATION..............8J-22
OIL - DESCRIPTION, REFRIGERANT......24-65
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-3
OIL - OPERATION, REFRIGERANT........24-65
OIL COOLER & LINES - INSTALLATION....9-50
OIL COOLER & LINES - REMOVAL........9-50
OIL FILTER - INSTALLATION.............9-51
OIL FILTER - REMOVAL.................9-51
OIL GALLERY PLUGS - STANDARD
PROCEDURE, REPLACING ENGINE
CORE...............................9-34
OIL JET - DESCRIPTION................9-51
OIL JET - INSTALLATION...............9-51
OIL JET - REMOVAL...................9-51
OIL LEVEL - STANDARD PROCEDURE,
CHECK............................21-102
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-65
OIL LEVEL INDICATOR - DESCRIPTION,
LOW...............................8J-18
OIL LEVEL INDICATOR - OPERATION,
LOW...............................8J-18
OIL PAN - INSTALLATION...............9-52
OIL PAN - REMOVAL...................9-52
OIL PUMP - ASSEMBLY..............21-121
OIL PUMP - DESCRIPTION............21-120
OIL PUMP - DISASSEMBLY............21-120
OIL PUMP - OPERATION..............21-120
OIL PUMP CHAIN - INSTALLATION........9-54
OIL PUMP CHAIN - REMOVAL
...........9-53
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT
........................9-38
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
........................9-38
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
........................9-37
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
........................9-37OIL SEPARATOR - INSTALLATION.........9-50
OIL SEPARATOR - REMOVAL............9-50
OIL TEMPERATURE SENSOR -
DESCRIPTION........................9-56
OIL TEMPERATURE SENSOR -
INSTALLATION........................9-57
OIL TEMPERATURE SENSOR -
OPERATION..........................9-56
OIL TEMPERATURE SENSOR - REMOVAL . . . 9-57
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-10
OPENING COVER - INSTALLATION,
STEERING COLUMN..................23-66
OPENING COVER - REMOVAL, STEERING
COLUMN...........................23-66
OPENING DIMENSIONS -
SPECIFICATIONS.....................23-90
OPENING SEALS - INSTALLATION, DOOR . . 23-87
OPENING SEALS - REMOVAL, DOOR.....23-87
OUTBOARD - INSTALLATION...........8O-31
OUTBOARD - REMOVAL...............8O-30
OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR...........23-87
OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR..............23-87
OUTER TIE ROD END - DIAGNOSIS AND
TESTING...........................19-10
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-1
OUTLET - DESCRIPTION, POWER......8W-97-3
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, POWER.....8W-97-4
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER.......8W-97-4
OUTLET - REMOVAL, CIGAR LIGHTER . . 8W-97-2
OUTLET - REMOVAL, POWER.........8W-97-4
OUTLET TEMPERATURE SENSOR -
DESCRIPTION, AIR...................24-14
OUTLET TEMPERATURE SENSOR -
INSTALLATION, AIR...................24-15
OUTLET TEMPERATURE SENSOR -
OPERATION, AIR.....................24-15
OUTLET TEMPERATURE SENSOR -
REMOVAL, AIR......................24-15
OUTLETS - INSTALLATION, AIR.........24-32
OUTLETS - REMOVAL, AIR.............24-31
OUTPUT SHAFT BEARING -
INSTALLATION......................21-122
OUTPUT SHAFT BEARING - REMOVAL . . . 21-122
OUTPUT SHAFT SEAL - INSTALLATION . . 21-125
OUTPUT SHAFT SEAL - REMOVAL......21-125
PADS - INSTALLATION, STEPWELL
SCUFF.............................23-73
PADS - REMOVAL, STEPWELL SCUFF....23-72
PAINT CODES - SPECIFICATIONS........23-74
PAINT TOUCH-UP - DESCRIPTION.......23-74
PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-75
PAN - INSTALLATION, OIL...............9-52
PAN - REMOVAL, OIL..................9-52
PANEL - INSTALLATION, BACKLITE -
BULKHEAD TRIM.....................23-81
PANEL - INSTALLATION, BULKHEAD
TRIM..............................23-69
PANEL - INSTALLATION, INSTRUMENT
. . . 8L-29
PANEL - INSTALLATION, QUARTER TRIM
. . 23-72
PANEL - INSTALLATION, TRIM
.....23-20,23-35,
23-46
PANEL - REMOVAL, BACKLITE -
BULKHEAD TRIM
.....................23-81
PANEL - REMOVAL, BULKHEAD TRIM
....23-69
PANEL - REMOVAL, INSTRUMENT
.......8L-28
PANEL - REMOVAL, QUARTER TRIM
.....23-71
PANEL - REMOVAL, TRIM
....23-19,23-35,23-46
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT
............8A-2
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT
........................8A-1
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT
.......................23-61
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT
.......................23-57
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT
.......................23-55
VAINDEX 11
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR -
INSTALLATION, FUEL.................14-29
TEMPERATURE SENSOR -
INSTALLATION, INLET AIR.............14-30
TEMPERATURE SENSOR -
INSTALLATION, OIL....................9-57
TEMPERATURE SENSOR - OPERATION....24-30
TEMPERATURE SENSOR - OPERATION,
AIR OUTLET........................24-15
TEMPERATURE SENSOR - OPERATION,
AMBIENT...........................24-15
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR..................24-18,24-26
TEMPERATURE SENSOR - OPERATION,
FUEL..............................14-29
TEMPERATURE SENSOR - OPERATION,
IN-CAR............................24-19
TEMPERATURE SENSOR - OPERATION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - OPERATION,
OIL ................................9-56
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.....................21-141
TEMPERATURE SENSOR - REMOVAL.....24-30
TEMPERATURE SENSOR - REMOVAL,
AIR OUTLET........................24-15
TEMPERATURE SENSOR - REMOVAL,
AMBIENT...........................24-15
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR..................24-18,24-26
TEMPERATURE SENSOR - REMOVAL,
FUEL..............................14-29
TEMPERATURE SENSOR - REMOVAL,
IN-CAR............................24-19
TEMPERATURE SENSOR - REMOVAL,
INLET AIR..........................14-30
TEMPERATURE SENSOR - REMOVAL,
OIL ................................9-57
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-31
TENSIONER - INSTALLATION, CABLE......5-23
TENSIONER - INSTALLATION, TIMING
CHAIN..............................9-71
TENSIONER - OPERATION, SEAT BELT....8O-32
TENSIONER - REMOVAL, CABLE..........5-23
TENSIONER - REMOVAL, TIMING CHAIN . . . 9-70
TENSIONERS - DESCRIPTION, BELT........7-5
TENSIONERS - OPERATION, BELT..........7-5
TENSIONING AND SLIDE RAIL -
INSTALLATION........................9-66
TENSIONING AND SLIDE RAILS -
REMOVAL...........................9-61
TENSIONING RAIL - INSTALLATION,
TIMING CHAIN.......................9-66
TENSIONING RAIL - REMOVAL, TIMING
CHAIN..............................9-63
TERMINAL - INSTALLATION.........8W-01-10
TERMINAL - REMOVAL..............8W-01-9
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-3
TEST - DIAGNOSIS AND TESTING,
FUNCTION...........................24-3
TEST - STANDARD PROCEDURE,
CYLINDER LEAK DOWN.................9-3
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-10
TEST - STANDARD PROCEDURE, LOW
PRESSURE FUEL PUMP................14-3
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-10
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-7
TESTER - STANDARD PROCEDURE,
USING MICRO 420 BATTERY............8F-11
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - DIAGNOSIS AND
TESTING, VEHICLE....................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THERMOSTAT - INSTALLATION, ENGINE
COOLANT
............................7-16
THERMOSTAT - REMOVAL, ENGINE
COOLANT
............................7-15
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM
..............21-27
THREADED HOLE REPAIR -
DESCRIPTION
......................Intro.-5
TIE ROD END - DIAGNOSIS AND
TESTING, OUTER
.....................19-10TIE ROD END - INSTALLATION..........19-11
TIE ROD END - REMOVAL..............19-11
TIME DELAY RELAY - INSTALLATION.....8L-33
TIME DELAY RELAY - REMOVAL.........8L-32
TIMER MODULE - DESCRIPTION,
CENTRAL............................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL....................8E-2
TIMER MODULE - INSTALLATION,
CENTRAL............................8E-2
TIMER MODULE - OPERATION, CENTRAL . . 8E-2
TIMER MODULE - REMOVAL, CENTRAL....8E-2
TIMING CHAIN - INSTALLATION..........9-67
TIMING CHAIN - REMOVAL..............9-63
TIMING CHAIN COVER - INSTALLATION....9-60
TIMING CHAIN COVER - REMOVAL.......9-59
TIMING CHAIN TENSIONER -
INSTALLATION........................9-71
TIMING CHAIN TENSIONER - REMOVAL....9-70
TIMING CHAIN TENSIONING RAIL -
INSTALLATION........................9-66
TIMING CHAIN TENSIONING RAIL -
REMOVAL...........................9-63
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-3
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE CARRIER - INSTALLATION, SPARE . . . 22-10
TIRE CARRIER - REMOVAL, SPARE......22-10
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-6
TIRE ROTATION - STANDARD
PROCEDURE.........................22-5
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRES, SPECIFICATIONS...............22-10
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TO COOLER TUBE - INSTALLATION,
RETURN HOSE FROM GEAR............19-15
TO COOLER TUBE - INSTALLATION,
RETURN LINE FROM PUMP............19-15
TO COOLER TUBE - REMOVAL, RETURN
HOSE FROM GEAR...................19-15
TO COOLER TUBE - REMOVAL, RETURN
LINE FROM PUMP....................19-15
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-8
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . . 8W-01-8
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE.........................2-19
TONE WHEEL - INSTALLATION...........5-31
TONE WHEEL - REMOVAL...............5-31
TOOLS - AUDIO, SPECIAL...............8A-1
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-6
TOOLS - BRAKES, SPECIAL..............5-7
TOOLS - FRONT SUSPENSION, SPECIAL . . 19-11
TOOLS - FRONT SUSPENSION, SPECIAL....2-2
TOOLS - FUEL SYSTEM, SPECIAL........14-5
TOOLS - PARK BRAKE, SPECIAL.........5-23
TOOLS, IGNITION CONTROL - SPECIAL....8I-1
TOOLS, INSTALLATION - SPECIAL........9-14
TOOLS, NAG1 AUTOMATIC
TRANSMISSION - SPECIAL.............21-69
TOOLS, PROPELLER SHAFT - SPECIAL.....3-5
TOOLS, REAR AXLE - SPECIAL...........3-14
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL.....................8F-6
TOOLS, SPECIFICATIONS - SPECIAL......8F-17
TOP COVER - CLUSTER - INSTALLATION . . 23-62
TOP COVER - CLUSTER - REMOVAL.....23-62
TOP COVER - INSTALLATION
...........23-65
TOP COVER - REMOVAL
...............23-64
TOP COVER - TRAY - INSTALLATION
.....23-64
TOP COVER - TRAY - REMOVAL
.........23-63
TOUCH-UP - DESCRIPTION, PAINT
.......23-74TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-75
TOWING - STANDARD PROCEDURE........0-6
TRACK - INSTALLATION, CENTER........23-39
TRACK - REMOVAL, CENTER...........23-38
TRACTION CONTROL INDICATOR -
DESCRIPTION.......................8J-24
TRACTION CONTROL INDICATOR -
OPERATION.........................8J-24
TRACTION CONTROL MALFUNCTION
INDICATOR - DESCRIPTION............8J-25
TRACTION CONTROL MALFUNCTION
INDICATOR - OPERATION..............8J-25
TRAILER HITCH - INSTALLATION........13-10
TRAILER HITCH - REMOVAL.............13-9
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-13
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-13
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-14
TRANSDUCER - INSTALLATION, VACUUM . . 11-8
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-13
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-14
TRANSDUCER - REMOVAL, VACUUM......11-7
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC............21-23,21-24
TRANSMISSION - INSTALLATION, REAR
CROSSMEMBER......................13-9
TRANSMISSION - NAG1 - DESCRIPTION,
AUTOMATIC..........................21-2
TRANSMISSION - NAG1 - OPERATION,
AUTOMATIC..........................21-4
TRANSMISSION - REMOVAL, REAR
CROSSMEMBER......................13-9
TRANSMISSION - SPECIAL TOOLS,
NAG1 AUTOMATIC....................21-69
TRANSMISSION - SPECIFICATIONS,
NAG1 AUTOMATIC....................21-68
TRANSMISSION CONTROL MODULE -
DESCRIPTION........................8E-5
TRANSMISSION CONTROL MODULE -
OPERATION..........................8E-5
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-103
TRANSMISSION FLUID - NAG1 -
DESCRIPTION, AUTOMATIC..............0-4
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-140
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-141
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY......................8N-2
TRANSPONDER KEY - DESCRIPTION......8Q-5
TRANSPONDER KEY - OPERATION........8Q-5
TRAY - DESCRIPTION, BATTERY.........8F-16
TRAY - INSTALLATION, BATTERY........8F-16
TRAY - INSTALLATION, TOP COVER......23-64
TRAY - OPERATION, BATTERY..........8F-16
TRAY - REMOVAL, BATTERY............8F-16
TRAY - REMOVAL, TOP COVER..........23-63
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, A-PILLAR........23-68
TRIM - INSTALLATION, B-PILLAR........23-69
TRIM - INSTALLATION, COWL..........23-70
TRIM - INSTALLATION, D-PILLAR........23-70
TRIM - REMOVAL, A-PILLAR...........23-67
TRIM - REMOVAL, B-PILLAR...........23-68
TRIM - REMOVAL, COWL..............23-70
TRIM - REMOVAL, D-PILLAR...........23-70
TRIM PANEL - INSTALLATION.....23-20,23-35,
23-46
TRIM PANEL - INSTALLATION, BACKLITE
- BULKHEAD........................23-81
TRIM PANEL - INSTALLATION,
BULKHEAD.........................23-69
TRIM PANEL - INSTALLATION, QUARTER . . 23-72
TRIM PANEL - REMOVAL
....23-19,23-35,23-46
TRIM PANEL - REMOVAL, BACKLITE -
BULKHEAD
.........................23-81
TRIM PANEL - REMOVAL, BULKHEAD
....23-69
TRIM PANEL - REMOVAL, QUARTER
.....23-71
TUBE - INSTALLATION, EXHAUST
........24-73
VAINDEX 17
Description Group-Page Description Group-Page Description Group-Page