2004 YAMAHA YZF-R1S Service Manual

5-91
CONNECTING RODS AND PISTONSENG
WARNING
CAUTION:

When the bolt is tightened more than the
specified angle, do not loosen the bolt and
then retighten it.
Replace the bolt with a new one and per-
form the procedure again.

If they are not flush with each other, remove
the connecting rod bolt and big end bear-
ing and restart from step “9”.
In this case, make sure to replace the con-
necting rod bolt.

Do not use a torque wrench to tighten the
bolt to the specified angle.

Tighten the bolt until it is at the specified
angles.
ProCarManuals.com

5-92
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7Removing the crankshaft
Crankcase
Connecting rod and connecting rod
caps
Crankshaft
Crankshaft journal lower bearing
Crankshaft journal upper bearing
Washer
Crankshaft drive gear
Pin
Pickup rotor1
5
5
1
1
1
1Remove the parts in the order listed.
Separate.
Refer to “CRANKCASE”.
Refer to “CONNECTING RODS AND
PISTONS”.
For installation, reverse the removal
procedure.
60 Nm (6.0 m
kg, 43 ft
lb)
CRANKSHAFTENG
EAS00381
CRANKSHAFT
ProCarManuals.com

5-93
CRANKSHAFTENG
CAUTION:
EAS00395
CHECKING THE CRANKSHAFT
1. Measure:

crankshaft runout
Out of specification
Replace the crank-
shaft.
Crankshaft runout
Less than 0.03 mm (0.0012 in)
2. Check:

crankshaft journal surfaces

crankshaft pin surfaces

bearing surfaces
Scratches / wear
Replace the crankshaft.
CHECKING THE CRANKSHAFT DRIVE
SPROCKET
1. Check:

crankshaft drive sprocket
1
Cracks / damage / wear
Replace the de-
fective part(s).
CHECKING THE CRANKSHAFT JOURNAL
BEARINGS
1. Measure:

crankshaft-journal-to-crankshaft-journal-
bearing clearance
Out of specification
Replace the crank-
shaft journal bearings.
Crankshaft-journal-to-crankshaft-
journal-bearing clearance
0.014
0.037 mm
(0.0006
0.0015 in)
: 0.10 mm (0.0039 in)
Do not interchange the crankshaft journal
bearings. To obtain the correct crankshaft-
journal-to-crankshaft-journal-bearing clear-
ance and prevent engine damage, the crank-
shaft journal bearings must be installed in
their original positions.
ProCarManuals.com

5-94
CRANKSHAFTENG
NOTE:
NOTE:
NOTE:
a. Clean the crankshaft journal bearings,
crankshaft journals, and bearing portions of
the crankcase.
b. Place the upper crankcase upside down on a
bench.
c. Install the crankshaft journal upper bearings
1 and the crankshaft into the upper crank-
case.
Align the projections
a on the crankshaft jour-
nal upper bearings with the notches
b in the up-
per crankcase.
d. Put a piece of Plastigauge
 2 on each
crankshaft journal.
Do not put the Plastigauge
 over the oil hole in
the crankshaft journal.
e. Install the crankshaft journal lower bearings
1 into the lower crankcase and assemble
the crankcase halves.

Align the projections
a of the crankshaft jour-
nal lower bearings with the notches
b in the
lower crankcase.

Do not move the crankshaft until the clearance
measurement has been completed.
f. Tighten the bolts to specification in the tight-
ening sequence cast on the crankcase.
Crankcase bolt
Bolt
1
10
1st: 20 Nm (2.0 m
kg, 14 ft
lb)
2nd: 20 Nm (2.0 m
kg, 14 ft
lb)
3rd: +60
Bolt
11
16
24 Nm (2.4 m
kg, 17 ft
lb)
Bolt
17
26
12 Nm (1.2 m
kg, 8.7 ft
lb)
M9  105 mm (4.1 in) bolts:
1
10
M8  60 mm (2.4 in) bolt: 11 LOCTITE
M8  60 mm (2.4 in) bolts: 12, 16
M6  70 mm (2.8 in) bolts: 19, 21, 23
M6  65 mm (2.5 in) bolts: 17, 18
M6  60 mm (2.4 in) bolts: 22, 24, 25
M6  50 mm (2.0 in) bolts: 20, 26
M8  50 mm (2.0 in) bolts: 13
15
ProCarManuals.com

5-95
CRANKSHAFTENG
NOTE:
NOTE:
* Following the tightening order, loosen the bolt
one by one and then retighten it to the specific
torque.
Lubricate the crankcase bolt threads with en-
gine oil.
Refer to “CRANKCASE”.
g. Remove the lower crankcase and the crank-
shaft journal lower bearings.
h. Measure the compressed Plastigauge

width c on each crankshaft journal.
If the crankshaft-journal-to-crankshaft-jour-
nal-bearing clearance is out of specification,
select replacement crankshaft journal bear-
ings.
2. Select:

crankshaft journal bearings (J1
J5)

The numbers
A stamped into the crankshaft
web and the numbers
1 stamped into the low-
er crankcase are used to determine the re-
placement crankshaft journal bearing sizes.

“J1
J5” refer to the bearings shown in the
crankshaft illustration.

If “J1
J5” are the same, use the same size
for all of the bearings.

If the size is the same for all “J
1 to J5” one digit
for that size is indicated. (Crankcase side only)
For example, if the crankcase “J
1” and crank-
shaft web “J
1” numbers are “6” and “2” respec-
tively, then the bearing size for “J1” is:
“J
1” (crankcase) – “J1”
(crankshaft web) – 1 =
6 – 2 – 1 = 3 (brown)
CRANKSHAFT JOURNAL BEARING
COLOR CODE
0White
1Blue
2Black
3Brown
4Green
ProCarManuals.com

5-96
CRANKSHAFTENG
NOTE:
60 Nm (6.0 m
kg, 43 ft
lb)
EAS00407
INSTALLING THE CRANKSHAFT
1. Install:

crankshaft journal upper bearings
1
(into the upper crankcase)
2. Lubricate:

crankshaft journal upper bearings
(with the recommended lubricant)
Recommended lubricant
Engine oil

Align the projections
a on the crankshaft jour-
nal upper bearings with the notches
b in the
upper crankcase.

Be sure to install each crankshaft journal up-
per bearing in its original place.
3. Install:

crankshaft
4. Install:

crankcase (lower)
Refer to “CRANKCASE”.
5. Install:

pin

pickup rotor
1

drive sprocket 2
ProCarManuals.com

5-97
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9
10
11
12Removing the transmission, shift
drum assembly, and shift forks
Crankcase lower
Drive axle assembly
Circlip
Oil seal
Bearing
Washer
Shift drum retainer
Spring
Shift fork guide bar
Shift fork “L”
Shift fork “R”
Shift drum assembly
Shift fork “C”1
1
1
1
1
2
2
2
1
1
1
1Remove the part in the order listed.
Separate.
Refer to “CRANKCASE”.
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
TRANSMISSIONENG
EAS00419
TRANSMISSION
TRANSMISSION, SHIFT DRUM ASSEMBLY AND SHIFT FORKS
ProCarManuals.com

5-98
TRANSMISSIONENG
Order Job / Part Q’ty Remarks
13
14
15
16
17Main axle retainer
Main axle assembly
Oil pipe
O-ring
Oil baffle plate1
1
1
2
1
For installation, reverse the removal
procedure.
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
ProCarManuals.com