2004 YAMAHA YZF-R1S Service Manual

8-40
SIGNALING SYSTEMELEC
YESNO
Replace the starting
circuit cut-off relay.
YESNO 4. Voltage

Connect the pocket tester (DC 20 V) to the
meter assembly coupler (wire harness side)
as shown.
The wiring circuit
from the main switch
to the meter assem-
bly coupler is faulty
and must be re-
paired. Positive tester probe
brown
Negative tester probe
ground
1

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of brown
at the meter assembly coupler (wire harness
side).

Is the voltage within specification?
This circuit is OK.

Are the tester readings correct?
YESNO 1. Oil level warning light (LEDs)

Check the oil level warning light for continu-
ity.
When the main switch is turn to “ON”, the oil
level warning light is come on.

Are the oil level warning light OK?
Replace the meter
assembly.
EAS00802
5. The oil level warning light fails to come on.
YESNO 2. Oil level switch

Drain the engine oil and remove the oil level
switch from the oil pan.

Connect the pocket tester (Ω
100) to the
oil level switch as shown.
Replace the oil level
switch. Positive tester probe

Connector (white)
Negative tester probe
Body ground
1
12

Measure the oil level switch resistance.
Oil level switch resistance
114  126 Ω at 20C (68F)
484  536 Ω at 20C (68F)
1
2

Is the oil level switch OK?
2
When you switch the positive and negative
tester probes, the readings in the above
chart will be reversed.
NOTE:
1
ProCarManuals.com

8-41
SIGNALING SYSTEMELEC
3. Voltage

Connect the pocket tester (DC 20 V) to the
meter assembly coupler (wire harness side)
as shown.
Positive tester probe
black / red
Negative tester probe
black / white
1
2

Turn the main switch to “ON”.

Measure the voltage (DC 12V) of black /
red and black / white at the meter as-
sembly coupler.

Is the voltage within specification?
12
YESNO
The wiring circuit
from the main switch
to the meter assem-
bly is faulty and must
be repaired.
This circuit is OK.
EAS00803
6. The fuel level warning light fails to come on.
1. Fuel sender

Drain the fuel from the fuel tank and remove
the fuel pump from the fuel tank.

Disconnect the fuel sender coupler from the
wire harness.

Connect the pocket tester (Ω
10) to the
fuel sender terminals as shown.
Positive tester probe
green / white
Negative tester probe
black
1
2
Fuel sender resistance
Full position of the float
20  26 Ω at 20C (68F)
Empty position of the float
134  140 Ω at 20C (68F)

Is the fuel sender OK? Measure the resistances when the float arm
is in contact with the full position and empty
position of the stopper.
NOTE:
Measure the fuel sender resistances.
YESNO
Replace the fuel
pump.
ProCarManuals.com

8-42
SIGNALING SYSTEMELEC
YESNO 2. Voltage

Connect the pocket tester (DC 20 V) to the
meter assembly coupler (wire harness side)
as shown.
The wiring circuit
from the main switch
to the meter assem-
bly coupler is faulty
and must be re-
paired. Positive tester probe
green / white
Negative tester probe
black / white
1
2

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of
green / white and black / white at the
meter assembly coupler.

Is the voltage within specification?
This circuit is OK.
12
Replace the multi-
function meter.
NO
1. Multi-function meter bulb socket

Check the multi-function meter bulb socket
for continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Is the multi-function meter bulb socket OK?
YES
EAS008067. The speedometer fails to come on.
2. Speed sensor

Connect the pocket tester (DC 20 V) to the
speed sensor coupler (wire harness side)
as shown.
Replace the speed
sensor.
NOYES
Positive tester probe
white / yellow
Negative tester probe
black / blue1
2

Set the main switch to “ON”.

Elevate the rear wheel and slowly rotate it.

Measure the voltage (DC 5 V) of white / yel-
low and blue. With each full rotation of the
rear wheel, the voltage reading should cycle
from 0.6 V to 4.8 V to 0.6 V to 4.8 V.

Does the voltage reading cycle correctly?
This circuit is OK.
ProCarManuals.com

8-43
COOLING SYSTEMELEC
EAS00807
COOLING SYSTEM
CIRCUIT DIAGRAM
ProCarManuals.com

8-44
1Main switch
4Fuse (main)
6Battery
14E.C.U.
28Coolant temperature sensor
73Fuse (ignition)
76Radiator fan motor relay
77Fuse (radiator fan motor left)
78Fuse (radiator fan motor right)
79Radiator fan motor 2
80Radiator fan motor 1
COOLING SYSTEMELEC
ProCarManuals.com

8-45
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?
YESNO
Replace the main
switch.
COOLING SYSTEMELEC
NOTE:
YESNO
1. Main, ignition and radiator fan motor fuses

Check the main, ignition and radiator fan
motor fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main, ignition and radiator fan motor
fuses OK?
Replace the fuse(s).
EAS00808
TROUBLESHOOTING

The radiator fan motor fails to turn.

The coolant temperature indicator light
fails to light when the engine is warm.
Check:
1. main, ignition, and radiator fan motor fuses
2. battery
3. main switch
4. radiator fan motor
5. radiator fan motor relay
6. coolant temperature sensor
7. wiring connections
(the entire cooling system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-46
YESNO
4. Radiator fan motor

Disconnect the radiator fan motor coupler
from the wire harness.

Connect the battery (DC 12 V) as shown.
The radiator fan mo-
tor is faulty and must
be replaced.
Positive battery lead
blue
Negative battery lead
black1
2

Does the radiator fan motor turn?
5. Radiator fan motor relay

Disconnect the radiator fan motor relay
form the wire harness.

Connect the pocket tester (Ω
1) and bat-
tery (12 V) to the radiator fan motor terminal
as shown.

Check the radiator fan motor for continuity.
Replace the radiator
fan motor relay.
NOYES
Battery positive terminal
red / white
Battery negative terminal

green / yellow 1
2

Does the radiator fan motor relay have conti-
nuity between red and brown / green?
Tester positive probe
red
Tester negative probe
brown / green3
4
COOLING SYSTEMELEC
EAS00809
ProCarManuals.com

8-47
COOLING SYSTEMELEC

Remove the coolant temperature sensor.

Connect the pocket tester (Ω
1k) to the
coolant temperature sensor as shown.

Immerse the coolant temperature sensor in
a container filled with coolant .
Make sure the coolant temperature sensor
terminals do not get wet.

Place a thermometer in the coolant.

Slowly heat the coolant, and then let it cool to
the specified temperature indicated in the
table.

Check the coolant temperature sensor for
continuity at the temperatures indicated in
the table.
EAS00812
1
Coolant temperature sensor
resistance
0C (32F): 5.21  6.37 kΩ
80C (176F): 0.29  0.35 kΩ
WARNING

Handle the coolant temperature sensor
with special care.

Never subject the coolant temperature
sensor to strong shocks. If the coolant
temperature sensor is dropped, replace
it.
6. Coolant temperature sensor
Replace the coolant
temperature sensor.
NOYES
Coolant temperature sensor
20 Nm (2.0 m
kg, 14 ft
lb)
Three bond sealock
10

Does the coolant temperature sensor oper-
ate properly?
7. Wiring

Check the entire cooling system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the cooling system’s wiring properly con-
nected and without defects?
Properly connect or
repair the cooling
system’s wiring.
NOYES
This circuit is OK.
EAS00813
2
NOTE:
3
ProCarManuals.com