2004 SUBARU FORESTER starter

EN(H4SO)-37
ENGINE (DIAGNOSTIC)
Inspection Mode
12.Inspection Mode
A: OPERATION
Perform the diagnosis on the “Diagnosis Trouble Codes (DTC) List” below.
Refer to the item of drive cycle when perform the diagnosis not on the “Diagnosis Trouble Codes (DTC) List”
below.
DTC Item
P0030 HO2S Heater Control Circuit (Bank 1 Sensor 1)
P0031 HO2S Heater Control Circuit Low (Bank 1 Sensor 1)
P0032 HO2S Heater Control Circuit High (Bank 1 Sensor 1)
P0037 HO2S Heater Control Circuit Low (Bank 1 Sensor 2)
P0038 HO2S Heater Control Circuit High (Bank 1 Sensor 2)
P0068 Manifold Pressure Sensor Range/Performance
P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input
P0112 Intake Air Temperature Circuit Low Input
P0113 Intake Air Temperature Circuit High Input
P0117 Engine Coolant Temperature Circuit Low Input
P0118 Engine Coolant Temperature Circuit High Input
P0122 Throttle/Pedal Position Sensor/Switch “A” Circuit Low Input
P0123 Throttle/Pedal Position Sensor/Switch “A” Circuit High Input
P0129 Barometric Pressure Too Low
P0131 O
2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
P0132 O
2 Sensor Circuit High Voltage (Bank 1 Sensor 1)
P0134 O
2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0137 O
2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)
P0138 O
2 Sensor Circuit High Voltage (Bank 1 Sensor 2)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0335 Crankshaft Position Sensor “A” Circuit
P0336 Crankshaft Position Sensor “A” Circuit Range/Performance
P0340 Camshaft Position Sensor “A” Circuit (Bank 1 or Single Sensor)
P0341 Camshaft Position Sensor “A” Circuit Range/Performance (Bank 1 or Single Sensor)
P0458 Evaporative Emission Control System Purge Control Valve Circuit Low
P0462 Fuel Level Sensor Circuit Low Input
P0463 Fuel Level Sensor Circuit High Input
P0502 Vehicle Speed Sensor Circuit Low Input
P0503 Vehicle Speed Sensor Intermittent/Erratic/High
P0512 Starter Request Circuit
P0513 Incorrect Immobilizer Key
P0519 Idle Control System Malfunction (Fail-Safe)
P0565 Cruise Control On Signal
P0604 Internal Control Module Random Access Memory (RAM) Error
P0703 Torque Converter/Brake Switch “B” Circuit
P0705 Transmission Range Sensor Circuit (PRNDL Input)
P0710 Transmission Fluid Temperature Sensor Circuit
P0716 Torque converter turbine speed sensor
P0720 AT Vehicle Speed Sensor Circuit Malfunction
P0726 Engine Speed Input Circuit Malfunction
P0731 Gear 1 Incorrect Ratio
P0732 Gear 2 Incorrect Ratio
P0733 Gear 3 Incorrect Ratio

EN(H4SO)-38
ENGINE (DIAGNOSTIC)
Inspection Mode
P0734 Gear 4 Incorrect Ratio
P0741 Torque Converter Clutch Circuit Performance or Stuck Off
P0743 Torque Converter Clutch Circuit Electrical
P0748 Pressure Control Solenoid “A” Electrical
P0753 Shift Solenoid “A” Electrical
P0758 Shift Solenoid “B” Electrical
P0771 Low clutch timing solenoid
P0778 Pressure Control Solenoid “B” Electrical
P0785 Shift/Timing Solenoid
P0851 Neutral Switch Input Circuit Low
P0852 Neutral Switch Input Circuit High
P0864 TCM Communication Circuit Range/Performance
P0865 TCM Communication Circuit Low
P0866 TCM Communication Circuit Low
P1110 Atmospheric Pressure Sensor Circuit Malfunction (Low Input)
P1111 Atmospheric Pressure Sensor Circuit Malfunction (High Input)
P1492 EGR Valve Signal #1 Circuit Malfunction (Low Input)
P1493 EGR Valve Signal #1 Circuit Malfunction (High Input)
P1494 EGR Valve Signal #2 Circuit Malfunction (Low Input)
P1495 EGR Valve Signal #2 Circuit Malfunction (High Input)
P1496 EGR Valve Signal #3 Circuit Malfunction (Low Input)
P1497 EGR Valve Signal #3 Circuit Malfunction (High Input)
P1498 EGR Valve Signal #4 Circuit Malfunction (Low Input)
P1499 EGR Valve Signal #4 Circuit Malfunction (High Input)
P1510 ISC Solenoid Valve Signal #1 Circuit Malfunction (Low Input)
P1511 ISC Solenoid Valve Signal #1 Circuit Malfunction (High Input)
P1512 ISC Solenoid Valve Signal #2 Circuit Malfunction (Low Input)
P1513 ISC Solenoid Valve Signal #2 Circuit Malfunction (High Input)
P1514 ISC Solenoid Valve Signal #3 Circuit Malfunction (Low Input)
P1515 ISC Solenoid Valve Signal #3 Circuit Malfunction (High Input)
P1516 ISC Solenoid Valve Signal #4 Circuit Malfunction (Low Input)
P1517 ISC Solenoid Valve Signal #4 Circuit Malfunction (High Input)
P1518 Starter Switch Circuit Low Input
P1560 Back-Up Voltage Circuit Malfunction
P1570 Antenna
P1571 Reference Code Incompatibility
P1572 EGI — Immobilizer Communication
P1574 Key — Communication Failure
P1576 EGI Control Module EEPROM
P1577 IMM Control Module EEPROM
P1698 Engine Torque Control Cut Signal Circuit Malfunction (Low Input)
P1699 Engine Torque Control Cut Signal Circuit Malfunction (High Input)
P1700 Throttle Position Sensor Circuit Malfunction For AT
P1711 Engine Torque Control Signal #1 Circuit Malfunction
P1712 Engine Torque Control Signal #2 Circuit MalfunctionDTC Item

EN(H4SO)-57
ENGINE (DIAGNOSTIC)
Diagnostics for Engine Starting Failure
17.Diagnostics for Engine Starting Failure
A: PROCEDURE
1. Check for fuel amount.
↓
2. Inspection of starter motor circuit. ure.>
↓
3. Inspection of ECM power supply and ground line. ENGINE CONTROL MODULE (ECM), Diagnostics for Engine Starting Failure.>
↓
4. Inspection of ignition control system. Failure.>
↓
5. Inspection of fuel pump circuit.
↓
6. Inspection of fuel injector circuit.

EN(H4SO)-58
ENGINE (DIAGNOSTIC)
Diagnostics for Engine Starting Failure
B: STARTER MOTOR CIRCUIT
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode ERATION, Clear Memory Mode.> and Inspection Mode tion Mode.>.
WIRING DIAGRAM:
EN-00261
12INHIBITOR SWITCH
STARTER
MOTOR
7P
RND321
SBF-4SBF-1
B14
B72
12
11
T7T3B12
13
IGNITION
SWITCH
1*2*
1*
2*
T7
123456789101112
B72
34
12
20
B136ECM
: AT MODEL
: MT MODEL1*
2*
BATTERY
B12
123456789101112
B136
5
2
84
3923 20 211011
221617
24
2512136
261915
14
1
7
18

EN(H4SO)-59
ENGINE (DIAGNOSTIC)
Diagnostics for Engine Starting Failure
Step Check Yes No
1 CHECK BATTERY.
Check the battery voltage.Is the voltage more than 12 V? Go to step 2.Charge or replace
the battery.
2 CHECK INPUT SIGNAL FOR STARTER MO-
TOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from starter
motor.
3) Turn the ignition switch to START.
4) Measure the power supply voltage between
starter motor connector terminal and engine
ground.
Connector & terminal
(B14) No. 1 (+) — Engine ground (
−):
N
OTE:
 For AT model, shift the select lever to “P” or
“N” range.
 For MT model, depress the clutch pedal.Is the voltage more than 10 V? Go to step 3.Go to step 4.
3 CHECK GROUND CIRCUIT OF STARTER
MOTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable terminal from
starter motor.
3) Measure the resistance of ground cable
between ground cable terminal and engine
ground.Is the resistance less than 5
Ω?Check the starter
motor. SC(H4SO)-6,
Starter.>Repair open circuit
of ground cable.
4 CHECK HARNESS BETWEEN BATTERY
AND IGNITION SWITCH CONNECTOR.
1) Disconnect the connector from ignition
switch.
2) Measure the power supply voltage between
ignition switch connector and chassis ground.
Connector & terminal
(B72) No. 1 (+) — Chassis ground (
−):Is the voltage more than 10 V? Go to step 5.Repair open circuit
in harness
between ignition
switch and bat-
tery, and check
fuse SBF No. 4
and SBF No. 1.
5 CHECK IGNITION SWITCH.
1) Disconnect the connector from ignition
switch.
2) Measure the resistance between ignition
switch terminals while turning the ignition
switch to START position.
Te r m i n a l s
No. 1 — No. 3:Is the resistance less than 5
Ω?Go to step 6.Replace the igni-
tion switch.
6 CHECK TRANSMISSION TYPE.Is the transmission type AT? Go to step 7.Temporary poor
contact occurs.
Check poor con-
tact in each con-
nectors.
7 CHECK INHIBITOR SWITCH INPUT VOLT-
AGE.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from inhibitor
switch.
3) Connect the connector to ignition switch.
4) Measure the input voltage between inhibitor
switch connector terminal and engine ground
while turning the ignition switch to START posi-
tion.
Connector & terminal
(B12) No. 12 (+) — Engine ground (
−):Is the voltage more than 10 V? Go to step 8.Repair open or
ground short cir-
cuit in harness
between inhibitor
switch and ignition
switch.
N
OTE:
Check security sys-
tem (if equipped).

EN(H4SO)-60
ENGINE (DIAGNOSTIC)
Diagnostics for Engine Starting Failure
8 CHECK INHIBITOR SWITCH.
1) Shift the select lever in the “P” or “N” range.
2) Measure the resistance between inhibitor
switch terminals.
Connector & terminal
(T3) No. 11 — No. 12:Is the resistance less than 1
Ω?Repair open or
ground short cir-
cuit in harness
between inhibitor
switch and starter
motor.Replace inhibitor
switch. 4AT-51, Inhibitor
Switch.> Step Check Yes No

EN(H4SO)-74
ENGINE (DIAGNOSTIC)
List of Diagnostic Trouble Code (DTC)
P0420 Catalyst System Efficiency Below
Threshold (Bank 1) BELOW THRESHOLD (BANK 1), Diagnostic Procedure with Diagnostic
Trouble Code (DTC).>
P0458 Evaporative Emission Control Sys-
tem Purge Control Valve Circuit Low TROL SYSTEM PURGE CONTROL VALVE CIRCUIT LOW, Diagnostic Pro-
cedure with Diagnostic Trouble Code (DTC).>
P0459 Evaporative Emission Control Sys-
tem Purge Control Valve Circuit High TROL SYSTEM PURGE CONTROL VALVE CIRCUIT HIGH, Diagnostic
Procedure with Diagnostic Trouble Code (DTC).>
P0461 Fuel Level Sensor Circuit Range/Per-
formance RANGE/PERFORMANCE, Diagnostic Procedure with Diagnostic Trouble
Code (DTC).>
P0462 Fuel Level Sensor Circuit Low Input INPUT, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0463 Fuel Level Sensor Circuit High Input HIGH INPUT, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0464 Fuel Level Sensor Circuit Intermittent INTERMITTENT, Diagnostic Procedure with Diagnostic Trouble Code
(DTC).>
P0483 Cooling Fan Rationality Check CHECK, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0502 Vehicle Speed Sensor Circuit Low
Input LOW INPUT, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0503 Vehicle Speed Sensor Intermittent/
Erratic/High HIGH INPUT, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0506 Idle Control System RPM Lower
Than Expected LOWER THAN EXPECTED, Diagnostic Procedure with Diagnostic Trouble
Code (DTC).>
P0507 Idle Control System RPM Higher
Than Expected HIGHER THAN EXPECTED, Diagnostic Procedure with Diagnostic Trouble
Code (DTC).>
P0512 Starter Request Circuit nostic Procedure with Diagnostic Trouble Code (DTC).>
P0513 Incorrect Immobilizer Key Procedure with Diagnostic Trouble Code (DTC).>
P0519 Idle Control System Malfunction
(Fail-Safe) TION (FAIL-SAFE), Diagnostic Procedure with Diagnostic Trouble Code
(DTC).>
P0565 Cruise Control On Signal Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0604 Internal Control Module Random
Access Memory (RAM) Error READ ACCESS MEMORY (RAM) ERROR, Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P0691 Cooling Fan 1 Control Circuit Low LOW, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0692 Cooling Fan 1 Control Circuit High HIGH, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P0703 Torque Converter/Brake Switch “B”
Circuit SWITCH “B” CIRCUIT, Diagnostic Procedure with Diagnostic Trouble Code
(DTC).>
P0705 Transmission Range Sensor Circuit
(PRNDL Input) dure without Diagnostic Trouble Code (DTC).>
P0710 Transmission Fluid Temperature
Sensor Circuit tic Procedure with Diagnostic Trouble Code (DTC).>
P0716 Torque converter turbine speed sen-
sor SENSOR, Diagnostic Procedure with Diagnostic Trouble Code (DTC).> DTC Item NOTE

EN(H4SO)-76
ENGINE (DIAGNOSTIC)
List of Diagnostic Trouble Code (DTC)
P1493 EGR Valve Signal #1 Circuit Malfunc-
tion (High Input) MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1494 EGR Valve Signal #2 Circuit Malfunc-
tion (Low Input) MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1495 EGR Valve Signal #2 Circuit Malfunc-
tion (High Input) MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1496 EGR Valve Signal #3 Circuit Malfunc-
tion (Low Input) MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1497 EGR Valve Signal #3 Circuit Malfunc-
tion (High Input) MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1498 EGR Valve Signal #4 Circuit Malfunc-
tion (Low Input) MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1499 EGR Valve Signal #4 Circuit Malfunc-
tion (High Input) MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diagnostic Trou-
ble Code (DTC).>
P1510 ISC Solenoid Valve Signal #1 Circuit
Malfunction (Low Input) CIRCUIT MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1511 ISC Solenoid Valve Signal #1 Circuit
Malfunction (High Input) CIRCUIT MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1512 ISC Solenoid Valve Signal #2 Circuit
Malfunction (Low Input) CIRCUIT MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1513 ISC Solenoid Valve Signal #2 Circuit
Malfunction (High Input) CIRCUIT MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1514 ISC Solenoid Valve Signal #3 Circuit
Malfunction (Low Input) CIRCUIT MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1515 ISC Solenoid Valve Signal #3 Circuit
Malfunction (High Input) CIRCUIT MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1516 ISC Solenoid Valve Signal #4 Circuit
Malfunction (Low Input) CIRCUIT MALFUNCTION (LOW INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1517 ISC Solenoid Valve Signal #4 Circuit
Malfunction (High Input) CIRCUIT MALFUNCTION (HIGH INPUT), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
P1518 Starter Switch Circuit Low Input INPUT, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P1560 Back-Up Voltage Circuit Malfunction FUNCTION, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
P1570 ANTENNA nostic Trouble Code (DTC).>
P1571 Reference Code Incompatibility nostics Procedure with Diagnostic Trouble Code (DTC).>
P1572 IMM Circuit Failure CIRCUIT), Diagnostics Procedure with Diagnostic Trouble Code (DTC).>
P1574 Key IMM Circuit Failure Procedure with Diagnostic Trouble Code (DTC).> DTC Item NOTE